Oklahoma Drainage and Sprinkler Repair – 405 203 9419

Sump Pump Installation

Oklahoma Drainage and Sprinkler Repair – 405 203 9419

Servicing Central and Western Oklahoma Sinch 1993.

Sump Pumps are used when water can’t be drained away by gravity.  You might have water standing in an area and it is up hill in all directions.

French Drains, Surface Drains, Channel Drains and Gutters can all be connected to a Sump Pump.  They can be connected exclusively or as a group.

A gravity flow French Drain or Surface Drain System will not work so you must pump the water to the Exit Point.  The Same holds true if you have water standing in a basement.  Pumping out the water is the only way.

Most Sump Pumps work automatically.

When the Sump Pump is under water a float rises up on the side of the pump and turns on the pump.  When the water is pumped away, the float falls back down and turns off the pump.  When water is flowing constantly on to the pump, it turns itself on and off over and over.  This could go on for hours or even days.

A Sump Pump Cavity looks like a trash can.  When water drains into the sump cavity it raises the float and turns on the pump. Once empty it falls down and turns off the Pump.

The larger the sump cavity the less often the sump turns on and off.   A small sump cavity wears out the sump pump faster because it turns on and off more making it less efficient.

 

 

Large volume custom sump cavities collect a large volume of water before the sump pump turns on.   Once on the Sump pump works for several minutes before turning off.  Once empty the larger sump cavity takes a longer time to refill again.  Which gives the pump a longer time to cool off and rest.

A sump pump in a large cavity will last much longer than one in a small cavity.

When you have a low-lying area that needs a French Drain, but it is up-hill in all directions and there is no way for the French Drain to move water to the Exit Point, a Sump Pump can be used.

Sump Pumps can also be used to pump water out of Basements or other enclosed low-lying areas.  Most Residential applications require a sump pump that has a power rating of 1 horse to 2 horse.  (Horse being horsepower)

Clean Water

A “Clean” pump must pump water that is relatively clean, or it will clog up after a while.

A” Dirty” Pump can handle water that is not so clean that has small pieces of Debris in it.

It will also clog if the debris is too thick or large.

There are several techniques that Oklahoma Drainage uses to keep a sump pump “Clog Free” and running well.

One technique

is to place the sump pump on top of a cement block inside the pump cavity.  Debris and unwanted solids fall the bottom of the sump cavity and never goes through the sump.  The sump cavity must then be cleaned out on a regular basis depending on the usual amount of debris.

Once a Year is typical.  Also putting a sump pump under a tree is a bad idea.  Leaves will clog up a sump faster than anything.  Pine needles are the worst.

Below is a Sump Pump connected to a Channel Drain.  The Sump Cavity is buried in the in the area where the dirt is disturbed.  As seen in the following picture.

The Homeowner had a sump Pump in their basement that was fed from a French Drain outside the Basement Wall.  The French Drain was 14 feet down along the Stem wall of the house.  The French Drainpipe was cheap and had collapsed.  We brought in a Mini Excavator and dug up the pipe and replaced it with Durable ADS 4 inch perf/soc French Drainpipe.  In the end, we were able to dig up the pipe and replace it.

Next, we installed a new exit for the water by installing a curb fitting.

No more flooding in the customers basement.  A few weeks later our customer was able to lay carpet in the basement with no problems.

Sump Pump Installation is necessary when water from a Drainage System can’t flow properly.  This means it is uphill in every direction from the Drain Intake.