Edmond Back-Flow Valve Repair. Oklahoma Drainage and Sprinkler Repair has Serviced Back-Flow Valves in Edmond Since 1993.
Oklahoma Drainage Installs Drainage Systems, and provides Expert Sprinkler System Repair.
Our Drainage Systems utilize French Drains, Surface Drains, Channel Drains, and Sump Pumps.
We Service all of Central Oklahoma including: Norman, Moore, Edmond, Yukon, Mustang, Oklahoma City, Midwest City, Del City, Blanchard, Newcastle, Purcell and Chickasha.
Back-Flow-Valve Service, Sprinkler Repair
Oklahoma Drainage and Sprinkler Repair Provides Service for Back-Flow-Valves and all types of Lawn Sprinkler Repair and Service. We have provided Expert Service for all of Central and Western Oklahoma Since 1993.
Back-Flow-Valves
There are two types of Back-Flow-Valves.
Above Ground
Below Ground Back-Flow-Valve.
What is a Back-Flow-Valve?
A Back-Flow-Valve is a part of a Lawn Sprinkler System. Water passes through it from the water source which can be a Water Meter or a Well Pump. It forces water to travel in only one direction from the source to the sprinkler system. It can’t travel backward back to the water source which again is a water meter or well pump.
A Back-Flow-Valve provides protection to the water source from back pressure and chemical contamination from lawn fertilizer.
Most Cities require a Back-Flow-Valve as “Code” for Sprinkler Installation.
Emergency Shut off
Back-Flow-Valves usually have an Emergency Shutoff valve on them that can shut off the water to the lawn sprinkler system but keep the water turned on to the home. Most Back-Flow-Valves have two Emergency Shut off Handles. Either one will work. Many times, they are hard to turn, however.
If there is a leak or water is shooting up in the air just turn the valve handle and give us a call.

Blue Emergency Shutoff handles for a Back-Flow-Valve.
Norman Sprinkler Checkup is a Central Focus for Oklahoma Drainage. We Performed or first Sprinkler Repair in Norman in 1993. It was in Brookhaven on the West side of Norman.
Recently we had a customer in Oklahoma City who wanted to move his Sprinkler Valves. They were in a bad place in his flower bed. He wanted to plant a tree where the valves were located.
We moved 4 Sprinkler Valves about feet out into the yard. All the Sprinkler Pipes had to be redesigned and installed matching the new location and maintaining full functionality.
What Is a Sprinkler Valve?
Think of a Sprinkler Valve as an “Off or on” Switch. The Sprinkler Controller turns the valves on or off.
It Sends a signal through a wire which is underground to the sprinkler valve somewhere in your yard.
Once turned on, the valve lets water pass through a sprinkler pipe to a specific group of sprinkler heads called a Sprinkler Zone. The controller allows water to reach the sprinkler heads for a certain amount of time running through the sprinkler valve. Once the time is up, it shuts off the sprinkler valve and moves on to the next valve in sequence.
Think of it as walking into every room in your house one at a time. As you enter you turn on the light. As you leave you turn off the light and move to the next room. You are the controller. The light switch represents the sprinkler valve.


Gutter Downspout Connected to 6 Inch French Drain
We Installed a Double Six inch French Drain in Edmond this week. A Double Six-Inch French Drain is two six inch French Drains laid side by side in one very wide and deep trench. It is designed to move a huge amount of water away from a home.
Lots of Drainage Problems
The customer had several different drainage problems in their back yard. After a thunderstorm, water would run under their back fence and into their garage. The back yard was on a steep hillside and the water would run very fast down the hill and into the garage.
Oklahoma Drainage installed 2 large six-inch French Drains across the water’s path. This allowed the water to be diverted into the French Drain which then ran through drainpipe to a curb outlet at the street. Three Gutter Down Spouts were connected into the French Drain.
The French Drain created a protective barrier for the garage. A 12-inch Surface Drain was also included in the Drainage System.
It was placed up against the driveway and connected with 4-inch Solid drainpipe to the 6 inch French Drain. Water was completely rerouted away from the home. A French Drain and Surface Drain combination in this case was the best solution to this particular drainage problem.

Installing a Curb Outlet for a French Drain in Edmond
























[…] Drainage System. The two most common exit points for a Drainage System are a Pop-Up Emitter or a Curb Fitting. A Pop-Up Emitter is a Fitting on the end of a Drain Pipe that has a lid that pops up and releases […]
[…] Drainage System. The two most common exit points for a Drainage System are a Pop-Up Emitter or a Curb Fitting. A Pop-Up Emitter is a Fitting on the end of a Drain Pipe that has a lid that pops up and releases […]