Drains around your home Installed, Edmond, Norman, Oklahoma City, Moore

Posted: November 1, 2019 in Drainage System, french drain, French Drain Repair
Tags: , , ,

If you have ever had standing water in the wrong place, a drainage system may be for you.  We install all kinds of drains including French Drains, Surface Drains, and Channel Drains.  Give us a call at 405 203 9419

Oklahoma Drainage and Sprinkler Repair, servicing all of Central and Western Oklahoma.

405 203 9419

French Drain Installation—   French Drains are designed to do a lot of things.  If you have an area that has unwanted water standing in it or running across it, a French Drain can be the answer. 

A French Drain is a trench that runs across the Drainage Problem Area. A French Drainpipe is placed in the bottom of the trench.  The French Drainpipe is perforated with thousands of small holes.  In most cases the Drainpipe has a nylon soc around the pipe to act as a filter for the French Drain

The French Drain trench is then filled with some type of small rock or stone. We typically use crushed 1 inch Limestone to cover the French Drainpipe.  The dirt that was dug out of the trench is taken away or spread out around the French Drain.  The Limestone replaces the dirt and fills the French Drain Trench all the way to the surface.

French Drain running to a curb outlet at the street

  Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out. Thousands of Sprinkler Heads have been adjusted. Countless Sprinkler Controllers have been Reprogramed or Replaced. We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many. I wonder how many?  A lot!!!! Oklahoma Drainage and Sprinkler Repair provides Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

French Drains Can

1.  Keep water away from foundations

A French Drain is best because it can move Surface Water and Sub-Surface Water (water moving underground) away from the foundation.  Many times, less experienced companies install Surface Drains to keep water away from foundations.  This can be a big mistake.  A Surface Drain can’t move or drain Sub-Surface Water.

Surface Drains Can’t Remove Ground Water

A Surface Drain often can’t move enough water fast enough and easily becomes overwhelmed during a heavy rain.  A Surface Drain also can’t cover or protect a broad enough area. Surface Drains should be designed in a Drainage System to be located in smaller Drainage Areas moving moderate amounts of water.  Surface Drains look better than French Drains. If, “appearance” is more important than Drainage Capacity, Go with the Surface Drain.  Just know what you are getting into and what your expectations should be. One side of a foundation alone, can be over 100 feet.  A 4 inch or 6-inch French Drain is best when protecting a large area such as a foundation.

Surface Drains Work Well in Smaller Areas

Keep water away from small or enclosed areas.  This might be a low area just through a gate on the side of a house, or the low area between a flowerbed and the wall of a house or standing water on or near a sidewalk or driveway. These types of Drainage Problems are best served with Surface Drains.
 
A Surface Drain can move water away from a low area that is relatively small.  This can occur in yards, flowerbeds, sidewalks and driveways. A Surface Drain is designed to move Surface Water away from a problem area to a predetermined exit point. Surface Drains are available in many sizes.  How quickly they remove standing water is usually determined by the size of the Drainpipe that is connected to the Drain.
Surface Drain Installation in Norman

French Drain Installation in Oklahoma City, Norman, Yukon, Mustang, Edmond, Lawton

Oklahoma Drainage and Sprinkler Repair 405 203 9419 — We provide:

    French Drain Installation, Surface Drain Installation, Drainage System Installation

    Sprinkler Repair for all aspects of Residential Sprinkler Systems

    Emergency Sprinkler Repair Service, AFTER HOURS AND WEEKENDS.

 

French Drain Installation, Oklahoma City, Duncan, Blanchard, New Castle, El Reno, Yukon, Mustang

Oklahoma Drainage – We install French Drains, Channel Drains, Surface Drains, Sump Pumps and Sod.

If You live in Oklahoma City and water damaging your foundation, we can install a French Drain for you.

 Or if you live in Norman and have water standing on your driveway, we can install a Channel Drain for you.

If you live in Edmond and have water flooding your basement, we can install a Sump Pump for you.

Or If you live in Moore and have water washing out your flower bed mulch, we can install a Surface Drain for you.

If you live in Yukon and need grass to grow, we can install Sod too!

Servicing all of Central and Western Oklahoma since 1993.

When Installing a French Drain as part of a Drainage System, there are many things to consider. What is the primary source of water coming into the problem drainage area. Are there secondary sources of water entering the area. What are they and how many. How fast does water enter the area and how often. What are the potential exit points for the water, Where do we want to take the water too.  Is there more than one potential exit point to increase drainage capacity. Does the customer want a Drainage System or a Flood Prevention System and does he understand the difference.

New French Drain

French Drain along stem wall.

 

new curb outlet

Curb outlet with more than 6 inches of fall

Oklahoma Drainage 405 203 9419 — We provide:

    French Drain Installation, Surface Drain Installation, Drainage System Installation

 

Drainage Systems, French Drains, Surface Drains, Channel Drains, Sump Pumps, with 30 years of experience. 

French Drain walkway

French Drain Installation under walkway

 

walk way french drain

Completed French Drain under walkway

Just what is a “French Drain?” Many times, people incorrectly use the phrase, “French Drain,” when they mean “Surface Drain” or “Channel Drain.”

A basic French Drain

consists of a Perforated Drainpipe in the bottom of a trench. The French Drain Trench runs through a Problem Drainage Area that needs to be drained.   The French Drainpipe is perforated (Full of Small Holes) and has Neo-Prene Soc around the pipe.  This soc helps prevent debris from clogging the French Drainpipe. The dirt that was taken out to make the trench is hauled away. It is replaced by some type of small stone or gravel depending on what is desired or available. I prefer crushed 1 inch lime stone. It is the most economical option in my area. Pea Gravel or some other type of small stone can work just as well. The limestone or gravel is placed in the trench on top of the perforated Drainpipe and filled all the way to the surface (ground level).

 

Oklahoma Drainage recently diagnosed a Drainage Problem in South Oklahoma City.  The Homeowner had a Deep French Drain down along the Stem wall of the house.  The French Drainpipe was cheap and had collapsed.  We brought in a Mini Excavator.

 They had a Sump Pump

in their basement that was fed from a French Drain outside the Basement Wall.  The French Drain was 14 feet down.  We used and Excavator and dug up the pipe and replaced it with Durable ADS 4 inch perf/soc French Drainpipe.  In the end, we were able to dig up the pipe and replace it.

Connecting Gutter into French Drain

New Trench for French Drain

Next, we installed a new exit for the water by installing a curb fitting. No more flooding in the customers basement.  A few weeks later our customer was able to lay carpet in the basement with no problems.

French Drain Installed Along Stem Wall

Oklahoma Drainage — Installing – French DrainsSurface DrainsChannel DrainsSump Pumps

 

Servicing all of Central and Western Oklahoma since 1993.

 

 

 

 

 

 

Oklahoma Drainage has been diagnosing and solving Drainage Problems since 1993. As a result, we have gained a tremendous amount of experience.

Water has the ability to get into places around your home where you really don’t want it to be. This is never a good thing! Some drainage problems are easy to solve.  Typically, water enters the problem drainage area one way from one source. The really tricky drainage problems occur when water enters the problem drainage area from multiple directions and from multiple sources.  Sometimes a secondary water source can’t be seen or identified until the primary water problem source is eliminated.

Think About

You have to think about all the possible ways water can get into the problem area.  Sometimes it is obvious.  Sometimes its hard to determine all the possible water sources.

French Drain walk way French Drain Installed along and under walkway to pool.

A drainage system is installed with a surface drain as the “intake” with drainage pipe running to an exit point.  Initially the water drains away and everything looks great.  The next day water is back and is all around the surface drain, but below the edge and it hasn’t rained at all, so no additional water ran over the surface of the ground to flood the area. The primary water source was solved, ( The surface water run off ) but the secondary water source was not.  Which was sub-surface water, (ground water) running into the area.  A surface drain can’t drain “ground water.”  A French Drain should have initially been installed instead of a Surface Drain.  A French Drain can drain both Surface Water and Ground Water.

A French Drain Can Handle Standing Water

Oklahoma Drainage Services all of Central Oklahoma including Norman, Moore, Edmond, Yukon, Mustang, Oklahoma City, Midwest City, Del City, Blanchard, Newcastle, Purcell and Chickasha.

Now we are expanding our service area to include

: Lawton, Altus, Duncan, Chickasha, Elk City, and all of Western Oklahoma.

 

 
Comments
  1. […] cases the Drain Pipe has a nylon soc around the pipe to act as a filter for the French Drain.  The French Drain trench is then filled with some type of small rock or stone.  We typically use crushed 1 inch Lime […]

  2. […] cases the Drain Pipe has a nylon soc around the pipe to act as a filter for the French Drain.  The French Drain trench is then filled with some type of small rock or stone.  We typically use crushed 1 inch Lime […]

  3. […] cases the Drain Pipe has a nylon soc around the pipe to act as a filter for the French Drain.  The French Drain trench is then filled with some type of small rock or stone.  We typically use crushed 1 inch Lime […]

  4. […] cases the Drain Pipe has a nylon soc around the pipe to act as a filter for the French Drain.  The French Drain trench is then filled with some type of small rock or stone.  We typically use crushed 1 inch Lime […]

  5. […] One Problem with connecting Gutter Down Spouts into a French Drain is overwhelming the Drainage System with too much water.  Three Gutter Down Spouts is usually OK to connect into a French Drain.  More than 3 Down Spouts can be too many.  The Drainage System Design should also take into account the size of the French Drain and the Gutters.  If you have a large long French Drain or over-sized gutters,  the number of Gutter Down Spouts connected into the French Drain Should be reduced.  This problem can usually be solved by increasing the size of the French DrainPipe.  This usually means moving up from a 4 inch French Drain Pipe to a 6 inch French Drain Pipe.  Four inch is the most common size of French Drain Pipe.  If you have more than 3 gutter Down Spouts to connect, you should move up to a 6 inch French Drain Pipe. […]

  6. […] One Problem with connecting Gutter Down Spouts into a French Drain is overwhelming the Drainage System with too much water.  Three Gutter Down Spouts is usually OK to connect into a French Drain.  More than 3 Down Spouts can be too many.  The Drainage System Design should also take into account the size of the French Drain and the Gutters.  If you have a large long French Drain or over-sized gutters,  the number of Gutter Down Spouts connected into the French Drain Should be reduced.  This problem can usually be solved by increasing the size of the French DrainPipe.  This usually means moving up from a 4 inch French Drain Pipe to a 6 inch French Drain Pipe.  Four inch is the most common size of French Drain Pipe.  If you have more than 3 gutter Down Spouts to connect, you should move up to a 6 inch French Drain Pipe. […]

  7. […] One Problem with connecting Gutter Down Spouts into a French Drain is overwhelming the Drainage System with too much water.  Three Gutter Down Spouts is usually OK to connect into a French Drain.  More than 3 Down Spouts can be too many.  The Drainage System Design should also take into account the size of the French Drain and the Gutters.  If you have a large long French Drain or over-sized gutters,  the number of Gutter Down Spouts connected into the French Drain Should be reduced.  This problem can usually be solved by increasing the size of the French Drain Pipe.  This usually means moving up from a 4 inch French Drain Pipe to a 6 inch French Drain Pipe.  Four inch is the most common size of French Drain Pipe.  If you have more than 3 gutter Down Spouts to connect, you should move up to a 6 inch French Drain Pipe. […]

  8. […] can:                                         A.  Leave the French Drain as-is, it will work well and look as it did for many […]

  9. […] can:                                         A.  Leave the French Drain as-is, it will work well and look as it did for many […]

  10. […] and can be used in many situations.  It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Down-Spouts connected to it. The main downfall of a French Drain is […]

  11. […] cases the Drain Pipe has a nylon soc around the pipe to act as a filter for the French Drain.  The French Drain trench is then filled with some type of small rock or stone.  We typically use crushed 1 inch Lime […]

  12. […] cases the Drain Pipe has a nylon soc around the pipe to act as a filter for the French Drain.  The French Drain trench is then filled with some type of small rock or stone.  We typically use crushed 1 inch Lime […]

  13. […] One Problem with connecting Gutter Down Spouts into a French Drain is overwhelming the Drainage System with too much water.  Three Gutter Down Spouts is usually OK to connect into a French Drain.  More than 3 Down Spouts can be too many.  The Drainage System Design should also take into account the size of the French Drain and the Gutters.  If you have a large long French Drain or over-sized gutters,  the number of Gutter Down Spouts connected into the French Drain Should be reduced.  This problem can usually be solved by increasing the size of the French Drain Pipe.  This usually means moving up from a 4 inch French Drain Pipe to a 6 inch French Drain Pipe.  Four inch is the most common size of French Drain Pipe.  If you have more than 3 gutter Down Spouts to connect, you should move up to a 6 inch French Drain Pipe. […]

  14. […] the Drain Pipe has a nylon soc around the pipe to act as a filter for the French Drain.  The French Drain trench is then filled with some type of small rock or stone.  We typically use crushed 1 inch […]

  15. […] French Drain Installed in Lawton […]

Leave a Reply