Sprinkler Service Oklahoma City. Oklahoma Drainage and Sprinkler Repair has provided Expert Sprinkler Repair and Service in Oklahoma City Since 1993.
Recently we fixed a broken Sprinkler Pipe under a driveway in Norman. It was leaking out onto the street every time the sprinkler system ran. The pipe had to be removed and a new PVC pipe put in its place.
It was located on the west side of Norman in Brookhaven.
Oklahoma Drainage and Sprinkler Repair provide Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties. We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.
Sprinkler Controller Repair is a service provided by Oklahoma Drainage. A Sprinkler Controller is the “Brain,” of a Sprinkler System. They can wear out or stop working. Power surges in the home can cause damage to a controller.
Programming can be difficult for homeowners. We can help with programming or replace a Sprinkler Module if it is defective.
Start Time Programming
“Start Time” programing many times is confusing for homeowners. The definition of a Start Time is a time that is chosen for the sprinkler system to start watering. It causes zone 1 to start running. When zone 1 is finished it automatically stops and zone 2 begins. When Zone 2 is complete it stops and zone 3 begins. Simple enough Right! This continues until the last zone programed available runs.
The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on. This is not the case. They follow zone 1 which has the only Start Time programmed into the controller.
Be Careful with Multiple Start Times, just use One at first.
Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available. These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.
For Example, the first Start Time is set at 9Am. Zone 1 begins to run at 9am. When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on. By 10 am let’s say all the zones have run. Let’s say 8 hours later you have a second start time at 6 Pm. Zone 1 comes on and runs and by 7pm all the zones have run again. So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.
Here is the big problem! Some Homeowners believe the second start time is to start zone 2 running. They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4. No!!
So, this is how they program the controller. At 9am they have a start time and zone 1 starts. The homeowner programs a second start time at 9:10 am to mistakenly start zone 2. Nope! It starts zone 1 all over again. At 9:2o they have a 3rd start time for zone 3. Nope! It starts zone 1 for a third time. Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.
If Sprinkler Controller Programming is confusing? Make sure you only have One Start Time!
“Run Time,” is completed Next. It determines how long each zone runs. Zone One 10 Minutes, Zone Two, 15 Minutes, Zone Three 8 Minutes. You can set how long you want each zone to run.
French Drain Repair and Installation is a Central Focus for Oklahoma Drainage. We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.
We started with the Valves
The Sprinkler Valves were located in the back yard near the pool. Six valves were located in one place. They were very tightly connected in one Manifold. None of the Sprinkler Valves had worked in a long time. They were Toro Valves that were over 20 years old. They all had to be replaced.
Surprisingly there was no shut-off valve for the Sprinkler Water. The water had to be shut off at the Meter so we could install a Manual Shut off valve. Once installed, the water was turned back on that ran to the house. The water that ran to the Sprinkler System was shut off with our New Shut Off Valve.
Rainbird Sprinkler Valve
The Sprinkler Valves Were Removed
Now, the 6 valves had to replaced. The valves that were used were made by Rain Bird. Before we began, I had to talk to the Customer. The previous valve design was a bad idea to repeat.
The original Sprinkler Valves were crammed into one large valve box in one very tight manifold. This is bad because the valves were too close to the fittings. Simply put, if one valve had to be replaced or worked on in the future, all 6 valves had to be taken out and replaced. If one valve was bad and 5 worked fine, they all still had to be replaced.
That’s Stupid!
I recommended that an additional Valve Box be installed putting 3 valves in each Valve Box. This would allow plenty of space between the valve fittings. If one Sprinkler Valve had to be adjusted or replaced in the future, the other 5 valves need not be disturbed. Simple Enough!
Check For Leaks
Once the valves were replaced and working, it was time to turn on each Sprinkler Zone, one at a time. Water was shooting up from the ground in several places in zone 1. Two broken Sprinkler Pipes and 5 bad Sprinkler Heads in zone 1 had to be fixed and replaced. We went through each of the 6 zones in similar fashion fixing lots of leaks and replacing bad sprinkler heads.
The Sprinkler Repair Cost About Half of the Cost of Completely New System.
Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair
Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.
Thousands of Sprinkler Heads have been adjusted.
Countless Sprinkler Controllers have been Reprogramed or Replaced.
Sprinkler Head Adjustment is a service provided by Oklahoma Drainage and Sprinkler Repair. We have adjusted sprinkler heads since 1993.
Many times, Sprinkler heads get, “Out of Wack.” Lawn mowers and weed eaters are notorious for this. Sprinkler heads start spraying water in the wrong place. It is frustrating to water concrete while plants and grass go without moisture.
Pop-Up Sprinkler Heads
Pop-Up Sprinkler Heads can be adjusted several ways. How far water goes to the left or right can be increased or decreased. The distance the water goes can also be increased or decreased. Finally, how high a sprinkler head pops up can be increased or decreased by installing a taller or shorter head.
Sometimes sprinkler heads spray a reduced distance and don’t perform very well due to water scale. Minerals in the water can completely clog a Pop-Up. Usually, the sprinkler nozzle on top of the sprinkler head, need only be replaced without replacing the entire head.
Rotor Sprinkler Heads also can be adjusted to the left or right. Spray Distance can be increased or decreased as well.
Needs Change
What’s going on in your yard can change. This calls for Sprinkler Head Adjustment. Adding or removing a swimming pool changes everything concerning sprinkler heads. Any number of things can change the necessary sprinkler head coverage.
Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps.
Providing Expert Sprinkler Repair – Broken Sprinkler Pipes – Sprinkler Head Adjustment – Sprinkler Valve Replacement
We provide Service for Folks in: Norman, Oklahoma City, Edmond, and Moore.
Central and Western Oklahoma is our Service Area since 1993.
(405) 203-9419
Check out Sprinkler System Check-Up
Sometimes things go wrong with sprinkler systems.
IF YOU NEED HELP IN THE MIDDLE OF THE NIGHT OR ON A WEEKEND WITH YOUR SPRINKLER SYSTEM, GIVE US A CALL.
OKLAHOMA DRAINAGE AND SPRINKLER REPAIR. 405 203 9419
IT MAY TAKE A FEW HOURS FOR US TO GET THERE BUT WE WILL COME TO HELP.
One Common problem is that they continue to run and won’t shut off. In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.
This can be temporarily solved by shutting of the Emergency Shutoff Valve. The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.
It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.
Many sprinkler systems in Oklahoma have them. (50 % ?) Under the plastic rock is a back-flow valve with two shut off handles. Usually, they have blue or green or tan handles. Turn one of the handles and it should shut off the water to your sprinkler system.
Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter. The valve box will have a green lid. Sometimes they are difficult to open. Many times, I had to pry them open with a flat head screwdriver.
Sprinkler Repair Facts
Oklahoma Drainage and Sprinkler Repair provides Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties. We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.
Sprinkler Controller Repair is a service provided by Oklahoma Drainage. A Sprinkler Controller is the “Brain,” of a Sprinkler System. They can wear out or stop working. Power surges in the home can cause damage to a controller.
Programming can be difficult for homeowners. We can help with programming or replace a Sprinkler Module if it is defective.
Start Time Programming
“Start Time” programing many times is confusing for homeowners. The definition of a Start Time is a time that is chosen for the sprinkler system to start watering. It causes zone 1 to start running. When zone 1 is finished it automatically stops and zone 2 begins. When Zone 2 is complete it stops and zone 3 begins. Simple enough Right! This continues until the last zone programed available runs.
The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on. This is not the case. They follow zone 1 which has the only Start Time programmed into the controller.
Be Careful with Multiple Start Times, just use One at first.
Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available. These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.
For Example, the first Start Time is set at 9Am. Zone 1 begins to run at 9am. When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on. By 10 am let’s say all the zones have run. Let’s say 8 hours later you have a second start time at 6 Pm. Zone 1 comes on and runs and by 7pm all the zones have run again. So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.
Here is the big problem! Some Homeowners believe the second start time is to start zone 2 running. They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4. No!!
So, this is how they program the controller. At 9am they have a start time and zone 1 starts. The homeowner programs a second start time at 9:10 am to mistakenly start zone 2. Nope! It starts zone 1 all over again. At 9:2o they have a 3rd start time for zone 3. Nope! It starts zone 1 for a third time. Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.
If Sprinkler Controller Programming is confusing? Make sure you only have One Start Time!
“Run Time,” is completed Next. It determines how long each zone runs. Zone One 10 Minutes, Zone Two, 15 Minutes, Zone Three 8 Minutes. You can set how long you want each zone to run.
French Drain Repair and Installation is a Central Focus for Oklahoma Drainage. We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.
We started with the Valves
The Sprinkler Valves were located in the back yard near the pool. Six valves were located in one place. They were very tightly connected in one Manifold. None of the Sprinkler Valves had worked in a long time. They were Toro Valves that were over 20 years old. They all had to be replaced.
Surprisingly there was no shut-off valve for the Sprinkler Water. The water had to be shut off at the Meter so we could install a Manual Shut off valve. Once installed, the water was turned back on that ran to the house. The water that ran to the Sprinkler System was shut off with our New Shut Off Valve.
The Sprinkler Valves Were Removed
Now, the 6 valves had to replaced. The valves that were used were made by Rain Bird. Before we began, I had to talk to the Customer. The previous valve design was a bad idea to repeat.
The original Sprinkler Valves were crammed into one large valve box in one very tight manifold. This is bad because the valves were too close to the fittings. Simply put, if one valve had to be replaced or worked on in the future, all 6 valves had to be taken out and replaced. If one valve was bad and 5 worked fine, they all still had to be replaced.
That’s Stupid!
I recommended that an additional Valve Box be installed putting 3 valves in each Valve Box. This would allow plenty of space between the valve fittings. If one Sprinkler Valve had to be adjusted or replaced in the future, the other 5 valves need not be disturbed. Simple Enough!
Check For Leaks
Once the valves were replaced and working, it was time to turn on each Sprinkler Zone, one at a time. Water was shooting up from the ground in several places in zone 1. Two broken Sprinkler Pipes and 5 bad Sprinkler Heads in zone 1 had to be fixed and replaced. We went through each of the 6 zones in similar fashion fixing lots of leaks and replacing bad sprinkler heads.
The Sprinkler Repair Cost About Half of the Cost of Completely New System.
Oklahoma Drainage Installs Drainage Systems, and provides Expert Sprinkler System Repair.
Our Drainage Systems utilize French Drains, Surface Drains, Channel Drains, and Sump Pumps.
We Service all of Central Oklahoma including: Norman, Moore, Edmond, Yukon, Mustang, Oklahoma City, Midwest City, Del City, Blanchard, Newcastle, Purcell and Chickasha.
Back-Flow-Valve Service, Sprinkler Repair
Oklahoma Drainage and Sprinkler Repair Provides Service for Back-Flow-Valves and all types of Lawn Sprinkler Repair and Service. We have provided Expert Service for all of Central and Western Oklahoma Since 1993.
Back-Flow-Valves
There are two types of Back-Flow-Valves.
Above Ground
Above Ground Back-Flow-Valve.
Below Ground Back-Flow-Valve.
Below Ground Back-Flow-Valve
What is a Back-Flow-Valve?
A Back-Flow-Valve is a part of a Lawn Sprinkler System. Water passes through it from the water source which can be a Water Meter or a Well Pump. It forces water to travel in only one direction from the source to the sprinkler system. It can’t travel backward back to the water source which again is a water meter or well pump.
A Back-Flow-Valve provides protection to the water source from back pressure and chemical contamination from lawn fertilizer.
Most Cities require a Back-Flow-Valve as “Code” for Sprinkler Installation.
Emergency Shut off
Back-Flow-Valves usually have an Emergency Shutoff valve on them that can shut off the water to the lawn sprinkler system but keep the water turned on to the home. Most Back-Flow-Valves have two Emergency Shut off Handles. Either one will work. Many times, they are hard to turn, however.
If there is a leak or water is shooting up in the air just turn the valve handle and give us a call.
Blue Emergency Shutoff handles for a Back-Flow-Valve.
Norman Sprinkler Checkup is a Central Focus for Oklahoma Drainage. We Performed or first Sprinkler Repair in Norman in 1993. It was in Brookhaven on the West side of Norman.
Recently we had a customer in Oklahoma City who wanted to move his Sprinkler Valves. They were in a bad place in his flower bed. He wanted to plant a tree where the valves were located.
We moved 4 Sprinkler Valves about feet out into the yard. All the Sprinkler Pipes had to be redesigned and installed matching the new location and maintaining full functionality.
