Oklahoma Drainage and Sprinkler Repair – 405 203 9419

Irrigation System Service.  Oklahoma Drainage and Sprinkler Repair can service your Irrigation System.

Lots of things can be done to make sure your Sprinkler System is ready to go.  All the Sprinkler Zones should be checked one by one.  The sprinkler heads and valves need to be checked to see if anything needs to be adjusted or replaced.

Sprinkler System Checkup is a Service Provided by Oklahoma Drainage since 1993.

Today we did a sprinkler repair in Norman.  The sprinkler system needed a checkup.

We went through each sprinkler zone and identified several different problems.

Zone 2 had a cracked sprinkler pipe in a flower bed.

A broken Rotor Sprinkler head was found immediately.

Next, zone five look good with no problems.

Zone 6 and 7 each had a couple of pop-up spray heads that were worn out and would not pop-up.  The diagnosis and the repair took less than two hours.  Now their sprinkler system is running great!

Now is a good time to have a Sprinkler System Checkup provided by Oklahoma Drainage.

Sprinkler Systems need to be checked before winter to prevent pipes from freezing.  Sprinkler Design determines whether sprinkler lines need to be bled.  Emergency shut off valves also need to be checked and turned off for the winter.

In the Spring, all the water needs to be turned back on and all sprinkler zones and heads need to be tested.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provide Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

Sprinkler Valves

Sprinkler Valve Replacement is a service that Oklahoma Drainage has provided Since 1993.  Recently we removed 3 Rainbird Sprinkler Valves and replaced them with new ones.  The valves had been crushed accidentally when a landscaper drove his truck across the yard.

Sprinkler System Check-Up in Edmond, Oklahoma City, Norman, and Moore.

 

 

Sprinkler System Check-Up process is very straightforward.  We run through all the Sprinkler Zones one-at-a- time from the controller. 

Sprinkler Controller

Sprinkler controllers can be a problem source.   Many times, the wires in the controller are loose or have a “Short” in one of the wires.  Sprinkler Programming can be a source of frustration.  We can help with Programming your controller.

We check all the sprinkler heads in that zone and the valves as well.

Once the Sprinkler System Checkup is Complete, we provide a Quote for what it will cost to make the needed repairs.

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes – Sprinkler Head Adjustment – Sprinkler Valve Replacement

Servicing all of Central and Western Oklahoma since 1993.  405 203 9419

Sprinkler Valve Replacement is a service that Oklahoma Drainage has provided Since 1993.  Recently we removed 3 Rainbird Sprinkler Valves and replaced them with new ones.  The valves had been crushed accidentally when a landscaper drove his truck across the yard.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provide Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

First Step

First, we dug up a good working area surrounding the broken Sprinkler Valves.  Next, we cut out the broken valves and crushed PVC pipes.  Finally, PVC pipe was cut and glued with new Sprinkler Valves following the original design and configuration.  In this case the three original sprinkler valves were connected to each other inside one Valve Box.

We aren’t done yet though; two sprinkler wires must be connected to each Valve.  One sprinkler wire is the “Common Ground.”  The other wire is the power wire.  All the sprinkler wiring is connected with water-proof wire connections.

The Common Ground wire and the Individual Power Wires all come from the Sprinkler Controller.  Each Sprinkler Valve has its own power wire coming from the Controller.  All the Sprinkler Valves are Connected to the Same Common Ground Wire.

Before We Finish

Before dirt can be put back around the new valves, testing must be done.  Each valve must be turned on, “one-at-a-time,” at the Controller to ensure good wire connection and functionality.  Also, the Sprinkler Valves must be checked for leaks in the PVC Pipe.

Oklahoma Drainage and Sprinkler Repair provides Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

Blanchard Sprinkler Repair has been provided by Oklahoma Drainage and Sprinkler Repair since 1993.

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,     Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

Oklahoma Drainage — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps

Servicing all of Central and Western Oklahoma since 1993.

 

 

A little bit North of Downtown Oklahoma City, We installed a 6-inch French Drain between two businesses which were less than three feet apart.  The French Drain went between a Law Firm and a Tire shop.  Water was leaking through the walls of both businesses.  Gutters between the two establishments were dumping a huge amount of water.  We installed a 6-inch French Drain between the house and the street.

It took a long time to get the dirt out of the trench for the French Drain.  It was a very tight fit.  We had to use a little red wagon to haul out the dirt for the French Drain and haul back in the crushed limestone for the French Drain.  It looked a little silly, but it was the only thing we could find that was narrow enough to fit between the buildings.  A French Drain that normally would take 1 day to install took three.

The French Drain had a Double Exit Point.  This means that once water entered the French Drain Pipe, it could run South to the street or it could run North to the alley.  To exit points greatly increases the water capacity for any French Drain.

Along the course of the French Drain, we connected two large gutters directly into the Drainpipe.

Once in place, the French Drain eliminated all the water that was leaking into the two buildings.

Drainage Problem Solved!