Oklahoma Drainage and Sprinkler Repair – 405 203 9419

Sump Pump Service

Oklahoma Drainage 405 203 9419 — We provide:

    French Drain Installation, Surface Drain Installation, Drainage System Installation

Oklahoma Drainage Installs Surface Drains and French Drains.  Sometimes it is up hill in all directions from the Problem Drainage Area.  This problem can be solved by installing a Sump Pump.  When the cavity fills, the water is pumped away to the point where the water exits the drain which can be a curb outlet or a pop-up emitter.

Two Sizes of Sump Pumps

Pump Size refers to how powerful it is not how physically large it is.  For Home or Small Business use a 1/3 Horse or a 1/2 Horse Works Best.  Larger Pumps such as a 1 Horse Pump must be ordered by a supplier and must be Hard Wired to 220 voltage by an electrician.

 

French Drain Running Through Low Areas

WHAT SIZE DRAINPIPE FOR FRENCH DRAINS?

French Drains can utilize several types and sizes of French Drainpipe.  An older type that is not commonly used any more is 4 inch PVC Pipe with large half inch holes drilled in the Pipe.  This doesn’t work very well,   Because the holes are too large and the number of holes in the French Drainpipe are too few.

 Also there is no filter or “Soc” around this particular French Drainpipe.  If it is used in sandy or loose soil the holes will clog and the pipe will fill up with sand.  PVC French Drainpipe should be avoided.

ADS French Drainpipe 

is much better, the holes are smaller and much more numerous.  It also comes inside a soc that acts as a filter and helps keep sand and debris out of the French Drainpipe.  It works very well.

For Small business and Residential French Drains, four-inch ADS Perf/Soc French Drainpipe is adequate and the most common.  It is used for the majority of all French Drains installed.  French Drains can be installed using 3 inch ADS Perf/Soc but many times it is too small and can be overwhelmed by a heavy rain or from a bad design.  (Too many gutter down spouts connected directly into the French Drain, For Example) Three Inch French Drainpipe should be avoided if possible.

Six inch  ADS Perf/Soc French Drainpipe is usually a good idea when possible.  It carries a much larger volume of water.  Six Inch French Drains are rarely overwhelmed.

Driveway Channel Drain

Sump Pump Service

Sump Pumps are used when water can’t be drained away by gravity.  You might have water standing in an area and it is up hill in all directions.  A gravity flow French Drain or Surface Drain System will not work so you must pump the water to the Exit Point.  The Same holds true if you have water standing in a basement.  Pumping out the water is the only way.

Most Sump Pumps work automatically.  When the Sump Pump is under water a float rises up on the side of the pump and turns on the pump.   Once the water is pumped away, the float falls back down and turns off the pump.  When water is flowing constantly on to the pump, it turns itself on and off over and over.  This could go on for hours or even days.

Two Sizes of Sump Pumps

Pump Size refers to how powerful it is not how physically large it is.  For Home or Small Business use a 1/3 Horse or a 1/2 Horse Works Best.  Larger Pumps such as a 1 Horse Pump must be ordered by a supplier and must be Hard Wired to 220 voltage by an electrician.

 

A Sump Pump Cavity

looks like a trash can.  When water drains into the sump cavity it raises the float and turns on the pump. Once empty it falls down and turns off the Pump.

The larger the sump cavity the less often the sump turns on and off.   A small sump cavity wears out the sump pump faster because it turns on and off more making it less efficient.

 

 

Large volume

custom sump cavities collect a large volume of water before the sump pump turns on.   Once on the Sump pump works for several minutes before turning off.  Once empty the larger sump cavity takes a longer time to refill again.  Which gives the pump a longer time to cool off and rest.

A sump pump in a large cavity will last much longer than one in a small cavity.

WHERE WE HAVE WORKED!

In 1993 we had no website.  I stuck little signs on the side of the road as advertisement.  I got my first Drain Installation work in March of 1993 in Norman.  It was in Brookhaven North of Robinson Street on the West side of I 35.

Over the years Oklahoma Drainage and Sprinkler Repair has installed all types of Drainage Systems in almost Every town in Central and Western Oklahoma.

The majority of our customers live in Oklahoma City, Norman, Edmond, Yukon, Mustang, Moore, Midwest City, Del City, Blanchard, New Castle, Yukon and Choctaw.

Oklahoma Drainage and Sprinkler Repair hasn’t been limited to those areas, however.  We have also installed French Drains, Surface Drains, Channel Drains, and Sump Pumps in many other cities.

When you have a low-lying area that needs a French Drain, but it is up-hill in all directions and there is no way for the French Drain to move water to the Exit Point, a Sump Pump can be used.

Sump Pumps can also be used to pump water out of Basements or other enclosed low-lying areas.  Most Residential applications require a sump pump that has a power rating of 1 horse to 2 horse.  (Horse being horsepower

Sump Pumps are used when water can’t be drained away by gravity.  You might have water standing in an area and it is up hill in all directions.

French Drains, Surface Drains, Channel Drains and Gutters can all be connected to a Sump Pump.

They can be connected exclusively or as a group.

 

A Sump Pump Cavity looks like a trash can.  When water drains into the sump cavity it raises the float and turns on the pump. Once empty it falls down and turns off the Pump.

The larger the sump cavity the less often the sump turns on and off.   A small sump cavity wears out the sump pump faster because it turns on and off more making it less efficient.

 

 

Clean Water

A “Clean” pump must pump water that is relatively clean, or it will clog up after a while.

A” Dirty” Pump can handle water that is not so clean that has small pieces of Debris in it.

It will also clog if the debris is too thick or large.

There are several techniques that Oklahoma Drainage uses to keep a sump pump “Clog Free” and running well.

One technique is to place the sump pump on top of a cement block inside the pump cavity.  Debris and unwanted solids fall the bottom of the sump cavity and never goes through the sump.  The sump cavity must then be cleaned out on a regular basis depending on the usual amount of debris.

Once a Year is typical.  Also putting a sump pump under a tree is a bad idea.  Leaves will clog up a sump faster than anything.  Pine needles are the worst.

Below is a Sump Pump connected to a Channel Drain.  The Sump Cavity is buried in the in the area where the dirt is disturbed.  As seen in the following picture.

The Homeowner had a Sump Pump

in their basement that was fed from a French Drain outside the Basement Wall.  The French Drain was 14 feet down along the Stem wall of the house.  The French Drainpipe was cheap and had collapsed.  We brought in a Mini Excavator and dug up the pipe and replaced it with Durable ADS 4 inch perf/soc French Drain pipe.  In the end, we were able to dig up the pipe and replace it.

Next, we installed a new exit for the water by installing a curb fitting.

No more flooding in the customers basement.  A few weeks later our customer was able to lay carpet in the basement with no problems.

Sump Pump Installation is necessary when water from a Drainage System can’t flow properly.  This means it is uphill in every direction from the Drain Intake.

 

 

Moore Oklahoma French Drain Installation, French Drain Repair

French Drain Installation Oklahoma City, Mustang, Lawton, Yukon, Edmond

Oklahoma Drainage 405 203 9419 — We provide:

    French Drain Installation, Surface Drain Installation, Drainage System Installation

Servicing all of Central and Western Oklahoma

 

FRENCH DRAIN CONNECTED TO GUTTERS

Many different types of Drains can be hooked together by one Drainpipe.  The Drainpipe then running to an Exit Point makes up a Drainage System.

One common type of Drain used in a Drainage System is A “French Drain.”  Many times a French Drain is installed close to a building foundation or in a low area next to a home or business.  This puts the French Drain in close proximity to Gutter Down Spouts.  Rather than have water come off the roof and out the Down Spout and on to the ground below, many times it is much better to tie a Gutter Down Spout Directly into a French Drain or near by Drainpipe depending on the Drainage System Design.

Connecting The Down Spouts Directly

into a French Drain is much  more efficient and causes suction to occur in the French Drain.  Connection of Gutter Down Spouts to a French Drain makes the Drainage System work better.

 

One Problem

with connecting Gutter Down Spouts into a French Drain is overwhelming the Drainage System with too much water.  Three Gutter Down Spouts is usually OK to connect into a French Drain.  More than 3 Down Spouts can be too many.  The Drainage System Design should also take into account the size of the French Drain and the Gutters.  If you have a large, long French Drain or over-sized gutters, the number of Gutter Down Spouts connected into the French Drain Should be reduced.

This problem can usually be solved by increasing the size of the French Drainpipe.  This usually means moving up from a 4 inch French Drainpipe to a 6 inch French Drainpipe.  Four inch is the most common size of French Drainpipe.  If you have more than 3 gutter Down Spouts to connect, you should move up to a 6 inch French Drainpipe.