Lawn Sprinkler Service Choctaw

This week Oklahoma Drainage and Sprinkler Repair overhauled a flowerbed Sprinkler Zone in a Sprinkler System in East Choctaw.  The homeowner had an existing Sprinkler System that was in good shape for the most part but had problems with the flowerbed Sprinkler Zone.

It had a Drip Sprinkler Zone installed.  The Drip Sprinkler System was installed correctly but was not practical for the flower bed.  The flowerbed was very sandy and could not retain water very well even with good mulch.  Plus, the surrounding brick walls increased the amount of heat the plants had to endure in the summer.  The Drip Sprinkler Zone could not provide enough water fast enough for the plants.

We provide:

1.  Sprinkler Valve Problems

2.  Sprinkler Wiring Problems

3.  Sprinkler Controller Problems / Sprinkler Clock Problems

4.  Sprinkler Head Problems

5.  Sprinkler Pipe Problems

6.  Sprinkler Coverage Problems

7.  Sprinkler Redesign Problems for new fences or swimming pools.

Oklahoma Drainage Installs Drainage Systems,  and provides Expert Sprinkler System Repair.

Our Drainage Systems utilize French Drains, Surface Drains, Channel Drains, and Sump Pumps.  

We Service all of Central Oklahoma including: Norman, Moore, Edmond, Yukon, Mustang, Oklahoma City, Midwest City, Del City, Blanchard, Newcastle, Purcell and Chickasha.

Sprinkler Leak Repair

Back-Flow-Valve Service, Sprinkler Repair

Oklahoma Drainage and Sprinkler Repair Provides Service for Back-Flow-Valves and all types of Lawn Sprinkler Repair and Service.  We have provided Expert Service for all of Central and Western Oklahoma Since 1993.

Back-Flow-Valves

There are two types of Back-Flow-Valves.

Above Ground

Above Ground Back-Flow-Valve.

Below Ground Back-Flow-Valve.

Below Ground Back-Flow-Valve

What is a Back-Flow-Valve?

A Back-Flow-Valve is a part of a Lawn Sprinkler System.  Water passes through it from the water source which can be a Water Meter or a Well Pump.  It forces water to travel in only one direction from the source to the sprinkler system.  It can’t travel backward back to the water source which again is a water meter or well pump.

A Back-Flow-Valve provides protection to the water source from back pressure and chemical contamination from lawn fertilizer.

Most Cities require a Back-Flow-Valve as “Code” for Sprinkler Installation.

Emergency Shut off

Back-Flow-Valves usually have an Emergency Shutoff valve on them that can shut off the water to the lawn sprinkler system but keep the water turned on to the home. Most Back-Flow-Valves have two Emergency Shut off Handles.  Either one will work.  Many times, they are hard to turn, however.

If there is a leak or water is shooting up in the air just turn the valve handle and give us a call.

Blue Emergency Shutoff handles for a Back-Flow-Valve.

Norman Sprinkler Checkup is a Central Focus for Oklahoma Drainage.  We Performed or first Sprinkler Repair in Norman in 1993.  It was in Brookhaven on the West side of Norman.

Recently we had a customer in Oklahoma City who wanted to move his Sprinkler Valves.  They were in a bad place in his flower bed.  He wanted to plant a tree where the valves were located.

We moved 4 Sprinkler Valves about feet out into the yard.  All the Sprinkler Pipes had to be redesigned and installed matching the new location and maintaining full functionality.

If you have water running down the street in the middle of the night because your sprinkler system is leaking or won’t shut off, give Oklahoma Drainage and Sprinkler Repair a call.  405 203 9419

Norman Sprinkler Repair, Edmond, Oklahoma City

Recently we fixed a broken Sprinkler Pipe under a driveway in Norman.  It was leaking out onto the street every time the sprinkler system ran.   The pipe had to be removed and a new PVC pipe put in its place.

It was located on the west side of Norman in Brookhaven.

Oklahoma Drainage and Sprinkler Repair provide Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Rainbird Sprinkler Controller

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,   Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

We started with the Valves

The Sprinkler Valves were located in the back yard near the pool.  Six valves were located in one place.  They were very tightly connected in one Manifold.  None of the Sprinkler Valves had worked in a long time.  They were Toro Valves that were over 20 years old.  They all had to be replaced.

Surprisingly there was no shut-off valve for the Sprinkler Water.  The water had to be shut off at the Meter so we could install a Manual Shut off valve.  Once installed, the water was turned back on that ran to the house.   The water that ran to the Sprinkler System was shut off with our New Shut Off Valve.

Rainbird Sprinkler Valve

The Sprinkler Valves Were Removed

Now, the 6 valves had to replaced.  The valves that were used were made by Rain Bird.  Before we began, I had to talk to the Customer.  The previous valve design was a bad idea to repeat.

The original Sprinkler Valves were crammed into one large valve box in one very tight manifold.  This is bad because the valves were too close to the fittings.  Simply put, if one valve had to be replaced or worked on in the future, all 6 valves had to be taken out and replaced.   If one valve was bad and 5 worked fine, they all still had to be replaced.

That’s Stupid!

I recommended that an additional Valve Box be installed putting 3 valves in each Valve Box.  This would allow plenty of space between the valve fittings.  If one Sprinkler Valve had to be adjusted or replaced in the future, the other 5 valves need not be disturbed.  Simple Enough!

Check For Leaks

Once the valves were replaced and working, it was time to turn on each Sprinkler Zone, one at a time.  Water was shooting up from the ground in several places in zone 1.  Two broken Sprinkler Pipes and 5 bad Sprinkler Heads in zone 1 had to be fixed and replaced.  We went through each of the 6 zones in similar fashion fixing lots of leaks and replacing bad sprinkler heads.

The Sprinkler Repair Cost About Half of the Cost of Completely New System.

Rotor and Pop-Up Sprinkler Heads

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

Sprinkler Head Adjustment is a service provided by Oklahoma Drainage and Sprinkler Repair.  We have adjusted sprinkler heads since 1993.

Many times, Sprinkler heads get, “Out of Wack.”  Lawn mowers and weed eaters are notorious for this.  Sprinkler heads start spraying water in the wrong place.  It is frustrating to water concrete while plants and grass go without moisture.

Pop-Up Sprinkler Heads

Pop-Up Sprinkler Heads can be adjusted several ways.  How far water goes to the left or right can be increased or decreased.  The distance the water goes can also be increased or decreased.  Finally, how high a sprinkler head pops up can be increased or decreased by installing a taller or shorter head.

Sometimes sprinkler heads spray a reduced distance and don’t perform very well due to water scale.  Minerals in the water can completely clog a Pop-Up.  Usually, the sprinkler nozzle on top of the sprinkler head, need only be replaced without replacing the entire head.

Rotor Sprinkler Heads also can be adjusted to the left or right.  Spray Distance can be increased or decreased as well.

Needs Change

What’s going on in your yard can change.  This calls for Sprinkler Head Adjustment.  Adding or removing a swimming pool changes everything concerning sprinkler heads.  Any number of things can change the necessary sprinkler head coverage.

Norman sprinkler repair

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains –

French Drain Installation in Oklahoma City

Oklahoma Drainage –  We install French Drains, Channel Drains, Surface Drains, Sump Pumps and Sod.

If You live in Oklahoma City and water damaging your foundation, We can install a French Drain for you.

If you live in Norman and have water standing on your driveway, We can install a Channel Drain for you.

If you live in Edmond and have water flooding your basement, We can install a Sump Pump for you.

If you live in Moore and have water washing out your flower bed mulch, We can install a Surface Drain for you.

If you live in Yukon and need grass to grow we can install Sod too!

Oklahoma Drainage  –  In business since 1993 – Servicing Central and Western Oklahoma

405 203 9419

Installing Curb Outlet for French Drain Exit

French Drain

Just what is a “French Drain?”  Many times people incorrectly use the phrase, “French Drain,” to apply to many different types of Drains that could be used in a Drainage System.  The term is widely used and many times incorrectly connected to “Surface Drains,” or “Channel Drains.”

A Surface Drain has a grate that sits on top of a basin.  The basin is underground.  A Drainpipe is connected underground to an outlet on the Drain Basin.  Storm-Water Drains through the grate into the Drain Basin.  Once in the Drain Basin, water travels out of the basin through a Drainpipe.  The Stormwater continues downhill in an underground Drainpipe to an exit point.

THIS IS NOT A FRENCH DRAIN!

A Surface Drain may come in many different shapes or sizes.  The Drain Grate may be round or square.  Here is a picture of a common Surface Drain.

A Channel Drain is a type of Surface Drain, and many times is installed in concrete across sidewalks or driveways.

A French Drain is completely different from a Surface Drain.  A basic French Drain consists of a Perforated Drainpipe in the bottom of a trench.  The Drain Pipe should have a neoprene sock around the Perforated Drainpipe.   This is to ensure that the Drainpipe does not become clogged.

The dirt that was taken out to make the trench is hauled away.  It is replaced by some type of small stone or gravel depending on what is desired or available.  I prefer crushed 1 inch lime stone.  It is the most economical option in my area.  Pea Gravel or some other type of small stone can work just as well.    The lime-stone or gravel is placed in the trench on top of the perforated Drainpipe and filled all the way to the surface (ground level).   In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drainpipe or the Gravel are installed.  This helps maintain the integrity of the trench over time.  It also increases the cost of the French Drain and the amount of time to install it.  I install a trench liner in a French Drain about 20% of the time.  Most of the time a liner in not needed.

DECORATIVE STONE CAN BE USED TO COVER A FRENCH DRAIN AND THEY LOOK GREAT AND LAST A LIFETIME.

French Drain with colored river rock along foundation