Oklahoma Drainage and Sprinkler Repair – 405 203 9419

Lawn Sprinkler Leaks.

Lawn Sprinklers can have pipes that leak.   PVC Pipe is the most common Sprinkler System Pipe and leaks definitely are possible.

Sprinkler Pipe Repair

Leaking Sprinkler Pipes

Leaks can occur near Sprinkler Valves.  Water travels through Sprinkler Valves and can leak going in or coming out.

Many Cities require a back-flow valve to protect the City’s water supply.  It can also leak as water passes through the valve.

Leaks can also occur due to tree roots stressing Sprinkler Pipes.  The pipes can be twisted by roots and crack or break.

Water inside Sprinkler Pipes can freeze and break or crack the PVC Pipe.

Move sprinkler heads, Norman, Oklahoma City, Edmond

There are many reasons for moving Sprinkler Heads.

If you put in a new pool, most of the sprinkler heads will need to be moved.

Sprinkler Heads need to be moved if you have new landscaping installed.

Sometimes Sprinkler Heads weren’t in a good place to begin with.  They need to be moved!

Oklahoma Drainage and Sprinkler Repair can help.  We have been moving Sprinkler Heads since 1993.

In 32 years, we have moved a lot of Heads for Customers in Central and Western Oklahoma.

Oklahoma Drainage and Sprinkler Repair provide Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

Emergency Sprinkler Repair is also available.

405 203 9419

Moving Sprinkler Head

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Rainbird Sprinkler Controller

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,   Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

We started with the Valves

The Sprinkler Valves were located in the back yard near the pool.  Six valves were located in one place.  They were very tightly connected in one Manifold.  None of the Sprinkler Valves had worked in a long time.  They were Toro Valves that were over 20 years old.  They all had to be replaced.

Surprisingly there was no shut-off valve for the Sprinkler Water.  The water had to be shut off at the Meter so we could install a Manual Shut off valve.  Once installed, the water was turned back on that ran to the house.   The water that ran to the Sprinkler System was shut off with our New Shut Off Valve.

Rainbird Sprinkler Valve

The Sprinkler Valves Were Removed

Now, the 6 valves had to replaced.  The valves that were used were made by Rain Bird.  Before we began, I had to talk to the Customer.  The previous valve design was a bad idea to repeat.

The original Sprinkler Valves were crammed into one large valve box in one very tight manifold.  This is bad because the valves were too close to the fittings.  Simply put, if one valve had to be replaced or worked on in the future, all 6 valves had to be taken out and replaced.   If one valve was bad and 5 worked fine, they all still had to be replaced.

That’s Stupid!

I recommended that an additional Valve Box be installed putting 3 valves in each Valve Box.  This would allow plenty of space between the valve fittings.  If one Sprinkler Valve had to be adjusted or replaced in the future, the other 5 valves need not be disturbed.  Simple Enough!

Check For Leaks

Once the valves were replaced and working, it was time to turn on each Sprinkler Zone, one at a time.  Water was shooting up from the ground in several places in zone 1.  Two broken Sprinkler Pipes and 5 bad Sprinkler Heads in zone 1 had to be fixed and replaced.  We went through each of the 6 zones in similar fashion fixing lots of leaks and replacing bad sprinkler heads.

The Sprinkler Repair Cost About Half of the Cost of Completely New System.

Rotor and Pop-Up Sprinkler Heads

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

Sprinkler Head Adjustment is a service provided by Oklahoma Drainage and Sprinkler Repair.  We have adjusted sprinkler heads since 1993.

Many times, Sprinkler heads get, “Out of Wack.”  Lawn mowers and weed eaters are notorious for this.  Sprinkler heads start spraying water in the wrong place.  It is frustrating to water concrete while plants and grass go without moisture.

Pop-Up Sprinkler Heads

Pop-Up Sprinkler Heads can be adjusted several ways.  How far water goes to the left or right can be increased or decreased.  The distance the water goes can also be increased or decreased.  Finally, how high a sprinkler head pops up can be increased or decreased by installing a taller or shorter head.

Sometimes sprinkler heads spray a reduced distance and don’t perform very well due to water scale.  Minerals in the water can completely clog a Pop-Up.  Usually, the sprinkler nozzle on top of the sprinkler head, need only be replaced without replacing the entire head.

Rotor Sprinkler Heads also can be adjusted to the left or right.  Spray Distance can be increased or decreased as well.

Needs Change

What’s going on in your yard can change.  This calls for Sprinkler Head Adjustment.  Adding or removing a swimming pool changes everything concerning sprinkler heads.  Any number of things can change the necessary sprinkler head coverage.

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes – Sprinkler Head Adjustment – Sprinkler Valve Replacement

We provide Service for Folks in: Norman, Oklahoma City, Edmond, and Moore.

Central and Western Oklahoma is our Service Area since 1993.  

                                                           (405) 203-9419

Check out Sprinkler System Check-Up

Emergency Sprinkler Repair

Sometimes things go wrong with sprinkler systems.

IF YOU NEED HELP IN THE MIDDLE OF THE NIGHT OR ON A WEEKEND WITH YOUR SPRINKLER SYSTEM, GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR.  405 203 9419

IT MAY TAKE A FEW HOURS FOR US TO GET THERE BUT WE WILL COME TO HELP.

One Common problem is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

Sprinkler Valve Box

Inside the valve box is a plastic handle that can turn off the water to the sprinkler system.  It can be blue or red or grey in color.

Many times, the valve box will be full of dirt, and you can’t turn or even see the handle until some of the dirt has been dug out by hand.

Water might be shooting up in the air somewhere on your property.  This can be caused by a broken sprinkler pipe or sprinkler valve.

SHUT OFF THE SPRINKLER WATER IF YOU CAN AND GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR. SERVICING ALL OF CENTRAL AND WESTERN OKLAHOMA.

405 203 9419

Servicing Oklahoma City, Norman, Edmond and all of Central and Western Oklahoma

Oklahoma Drainage –

Hey Oklahoma, we are expanding to service all of Western Oklahoma as well as Central Oklahoma.  If you live in Elk City, and need a French Drain, we can help.  If water is standing on your driveway in Clinton, Give us a call.  Duncan, Lawton, and Altus are all new areas of service for us.

Since 1993 Oklahoma Drainage and Sprinkler Repair has solved all types of standing water and drainage issues.  We install Drainage Systems that utilize French Drains, Surface, Drains, Channel Drains, and Sump Pumps depending on the customers needs.

If you have water in a place where you don’t want it, we can help.

Running Gutter Drainpipe Across Driveway

French Drains as part of a Drainage System – 

Many times, people use the term ” French Drain” as general name for a Drain used in or around your home.  French Drains are designed to move a lot of water over a large, flooded area.  They are also designed to take water in on the surface of the ground or below the surface of the ground.  This is very important if the water coming into the flooded area is moving through the ground or coming up from underneath.  ” Sub Surface Water Movement.”  The picture below is not a French Drain!

Surface Drain

A French Drain looks like this

A French Drain Can Handle Standing Water

A French Drain can take in water in a broad area.  It can move a much larger volume of water compared to a Surface Drain.  Also, it can move sub surface water moving into the area where a Surface Drain won’t move any water at all.

Surface Drains

are designed to move surface water only on a smaller scale in confined areas.

Each solves specific drainage problems.  A Drainage System may use one or both together or even several using many types of drains.

Do you have standing water in a large area in your yard?  Typically, this calls for a French Drain.  A French Drain is a great way to control standing water in a large grassy area.  It can also protect areas from flooding to a certain degree.  As long as the French Drains capacity to move water is not exceeded.  If the French Drains capacity is exceeded then water will stand in the drainage area until the rain stops and the drain has time to catch up.  A good way to prevent this is to install a bigger French Drain with a larger pipe.  The difference between a 3 inch French Drain and a 6 inch French Drain is huge.

Another way to beef up a French Drain is to connect gutter down spouts in front of the French Drain.  The water coming off the roof causes suction in the French Drain Behind it.  This greatly increases the French Drains ability to move water without increasing the size of the French Drainpipe.

Gutter Downspout Connected to 6 Inch French Drain

Recently we installed a French Drain inside the courtyard of a rest home in Norman.  We had several interesting challenges to overcome that were not typical for a French Drain Installation.  The court yard was in the center of the home and was a secure area for the patrons.  We had to put down painters’ tarps to run our wheelbarrows over.  We took out 44 loads of dirt and brought in 52 loads of Crushed one inch limestone for the French Drain.

French Drain in the Rest Home

Each trip was over a hundred yards from the trailer in the parking lot, in the front door, down the hall, making two turns along the way.  Each time we had to be escorted by security.  Needless to say, the installation of this particular drainage system took a while. In the above picture, the French Drain runs along the low area crossing all the areas where water would stand each time it rained.

French Drain in Rest Home Courtyard

When a French Drain is installed, a big mistake that is made by many people is to cover up the gravel with dirt.  This is a big mistake.  Basically, it is ” Putting the cork back in the bottle.”  If the French Drain is in full sun and has a type of grass surrounding it that spreads on its own such a ” Tift” or “Bermuda”, Grass will grow over it and the French Drain will eventually disappear.  Grass covering a French Drain is a good thing if it grows across the drain without adding dirt.  The Grass thatch acts a water filter preventing clogging and extending the life of the Drainage System.

Full Shade

When a French Drain is in Full Shade, or the surrounding grass will not spread on its own, such as with Fescue, other steps must be taken.  One option is to just leave it alone.  If you don’t mind how it looks, it will drain a large amount of water for many years.  Many times a French Drain can be a landscaping focal point.  They can be dressed up with all kinds of Rocks and Stones and Plants.

Just what is a “French Drain?”  Many times, people incorrectly

use the phrase, “French Drain,” to apply to many different types of Drains that could be used in a Drainage System.  The term is widely used and many times incorrectly connected to “Surface Drains,” or “Channel Drains.”

A Surface Drain

has a grate that sits on top of a basin.  The basin is underground.  A Drainpipe is connected underground to an outlet on the Drain Basin.  Stormwater Drains through the grate into the Drain Basin.  Once in the Drain Basin, water travels out of the basin through a Drainpipe.  The Stormwater continues downhill in an underground Drainpipe to an exit point.

THIS IS NOT A FRENCH DRAIN!

A Surface Drain may come in many different shapes or sizes.  The Drain Grate may be round or square.  Here is a picture of a common Surface Drain.

A Channel Drain is a type of Surface Drain, and many times is installed in concrete across sidewalks or driveways.

A French Drain is completely different from a Surface Drain.  A basic French Drain consists of a Perforated Drainpipe in the bottom of a trench.  The Drainpipe should have a neoprene sock around the Perforated Drainpipe.   This is to ensure that the Drainpipe does not become clogged.

Haul away the Dirt

The dirt that was taken out to make the trench is hauled away.  It is replaced by some type of small stone or gravel depending on what is desired or available.  I prefer crushed 1 inch limestone.  It is the most economical option in my area.  Pea Gravel or some other type of small stone can work just as well.

The limestone or gravel is placed in the trench on top of the perforated Drainpipe and filled all the way to the surface (ground level).   In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drainpipe or the Gravel are installed.  This helps maintain the integrity of the trench over time.  It also increases the cost of the French Drain and the amount of time to install it.  I install a trench liner in a French Drain.

The main downfall of a French Drain