Oklahoma Drainage and Sprinkler Repair – 405 203 9419

Sprinkler Service Oklahoma City.  Oklahoma Drainage and Sprinkler Repair has provided Expert Sprinkler Repair and Service in Oklahoma City Since 1993.

 

Recently we fixed a broken Sprinkler Pipe under a driveway in Norman.  It was leaking out onto the street every time the sprinkler system ran.   The pipe had to be removed and a new PVC pipe put in its place.

It was located on the west side of Norman in Brookhaven.

Oklahoma Drainage and Sprinkler Repair provide Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

 

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,   Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

We started with the Valves

The Sprinkler Valves were located in the back yard near the pool.  Six valves were located in one place.  They were very tightly connected in one Manifold.  None of the Sprinkler Valves had worked in a long time.  They were Toro Valves that were over 20 years old.  They all had to be replaced.

Surprisingly there was no shut-off valve for the Sprinkler Water.  The water had to be shut off at the Meter so we could install a Manual Shut off valve.  Once installed, the water was turned back on that ran to the house.   The water that ran to the Sprinkler System was shut off with our New Shut Off Valve.

The Sprinkler Valves Were Removed

Now, the 6 valves had to replaced.  The valves that were used were made by Rain Bird.  Before we began, I had to talk to the Customer.  The previous valve design was a bad idea to repeat.

The original Sprinkler Valves were crammed into one large valve box in one very tight manifold.  This is bad because the valves were too close to the fittings.  Simply put, if one valve had to be replaced or worked on in the future, all 6 valves had to be taken out and replaced.   If one valve was bad and 5 worked fine, they all still had to be replaced.

That’s Stupid!

I recommended that an additional Valve Box be installed putting 3 valves in each Valve Box.  This would allow plenty of space between the valve fittings.  If one Sprinkler Valve had to be adjusted or replaced in the future, the other 5 valves need not be disturbed.  Simple Enough!

Check For Leaks

Once the valves were replaced and working, it was time to turn on each Sprinkler Zone, one at a time.  Water was shooting up from the ground in several places in zone 1.  Two broken Sprinkler Pipes and 5 bad Sprinkler Heads in zone 1 had to be fixed and replaced.  We went through each of the 6 zones in similar fashion fixing lots of leaks and replacing bad sprinkler heads.

The Sprinkler Repair Cost About Half of the Cost of Completely New System.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

Sprinkler Head Adjustment is a service provided by Oklahoma Drainage and Sprinkler Repair.  We have adjusted sprinkler heads since 1993.

Many times, Sprinkler heads get, “Out of Wack.”  Lawn mowers and weed eaters are notorious for this.  Sprinkler heads start spraying water in the wrong place.  It is frustrating to water concrete while plants and grass go without moisture.

Pop-Up Sprinkler Heads

Pop-Up Sprinkler Heads can be adjusted several ways.  How far water goes to the left or right can be increased or decreased.  The distance the water goes can also be increased or decreased.  Finally, how high a sprinkler head pops up can be increased or decreased by installing a taller or shorter head.

Sometimes sprinkler heads spray a reduced distance and don’t perform very well due to water scale.  Minerals in the water can completely clog a Pop-Up.  Usually, the sprinkler nozzle on top of the sprinkler head, need only be replaced without replacing the entire head.

Rotor Sprinkler Heads also can be adjusted to the left or right.  Spray Distance can be increased or decreased as well.

Needs Change

What’s going on in your yard can change.  This calls for Sprinkler Head Adjustment.  Adding or removing a swimming pool changes everything concerning sprinkler heads.  Any number of things can change the necessary sprinkler head coverage.

 

 

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes – Sprinkler Head Adjustment – Sprinkler Valve Replacement

We provide Service for Folks in: Norman, Oklahoma City, Edmond, and Moore.

Central and Western Oklahoma is our Service Area since 1993.  

                                                           (405) 203-9419

Check out Sprinkler System Check-Up

Emergency Sprinkler Repair

Sometimes things go wrong with sprinkler systems.

 

IF YOU NEED HELP IN THE MIDDLE OF THE NIGHT OR ON A WEEKEND WITH YOUR SPRINKLER SYSTEM, GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR.  405 203 9419

IT MAY TAKE A FEW HOURS FOR US TO GET THERE BUT WE WILL COME TO HELP.

 

One Common problem is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

 

Sprinkler Repair Facts

 

Oklahoma Drainage and Sprinkler Repair provides Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

 

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,   Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

We started with the Valves

The Sprinkler Valves were located in the back yard near the pool.  Six valves were located in one place.  They were very tightly connected in one Manifold.  None of the Sprinkler Valves had worked in a long time.  They were Toro Valves that were over 20 years old.  They all had to be replaced.

Surprisingly there was no shut-off valve for the Sprinkler Water.  The water had to be shut off at the Meter so we could install a Manual Shut off valve.  Once installed, the water was turned back on that ran to the house.   The water that ran to the Sprinkler System was shut off with our New Shut Off Valve.

The Sprinkler Valves Were Removed

Now, the 6 valves had to replaced.  The valves that were used were made by Rain Bird.  Before we began, I had to talk to the Customer.  The previous valve design was a bad idea to repeat.

The original Sprinkler Valves were crammed into one large valve box in one very tight manifold.  This is bad because the valves were too close to the fittings.  Simply put, if one valve had to be replaced or worked on in the future, all 6 valves had to be taken out and replaced.   If one valve was bad and 5 worked fine, they all still had to be replaced.

That’s Stupid!

I recommended that an additional Valve Box be installed putting 3 valves in each Valve Box.  This would allow plenty of space between the valve fittings.  If one Sprinkler Valve had to be adjusted or replaced in the future, the other 5 valves need not be disturbed.  Simple Enough!

Check For Leaks

Once the valves were replaced and working, it was time to turn on each Sprinkler Zone, one at a time.  Water was shooting up from the ground in several places in zone 1.  Two broken Sprinkler Pipes and 5 bad Sprinkler Heads in zone 1 had to be fixed and replaced.  We went through each of the 6 zones in similar fashion fixing lots of leaks and replacing bad sprinkler heads.

The Sprinkler Repair Cost About Half of the Cost of Completely New System.

 

Oklahoma Drainage –  We install French Drains, Channel Drains, Surface Drains, Sump Pumps and Sod.

If You live in Oklahoma City and water damaging your foundation, We can install a French Drain for you.

If you live in Norman and have water standing on your driveway, We can install a Channel Drain for you.

If you live in Edmond and have water flooding your basement, We can install a Sump Pump for you.

If you live in Moore and have water washing out your flower bed mulch, We can install a Surface Drain for you.

If you live in Yukon and need grass to grow, we can install Sod too!

Servicing all of Central and Western Oklahoma since 1993.

 

If you have water standing in your flowerbed we can install a French Drain For you.  If water is standing on your driveway or sidewalk a Surface Drain or Channel Drain set in concrete might be what you need.  If water is standing in your basement a Sump Pump installation is a good idea.

We Installed a Double Six-inch French Drain in Edmond this week.  A Double Six-Inch French Drain is two six inch French Drains laid side by side in one very wide and deep trench.  It is designed to move a huge amount of water away from a home.   Our customer had several different drainage problems in their back yard.  After a thunderstorm, water would run under their back fence and into their garage.  The back yard was on a steep hillside, and the water would run very fast down the hill and into the garage.

6-Inch French Drain

Oklahoma Drainage and Sprinkler Repair installed 2 large six-inch French Drains across the water’s path.  This allowed the water to be diverted into the French Drain which then ran through drainpipe to a curb outlet at the street.  Three Gutter Down Spouts were connected into the French Drain.  The French Drain created a protective barrier for the garage.  A 12 inch Surface Drain was also included in the Drainage System.  It was placed up against the driveway and connected with 4 inch Solid drain pipe to the 6 inch French Drain.  Water was completely rerouted away from the home.  A French Drain and Surface Drain combination in this case was the best solution to this particular drainage problem.

Installing a Curb Outlet for a French Drain in Edmond

 

Oklahoma Drainage installed

a 4-inch French Drain in East Norman this week.  The customer had water standing on the side of his house that was causing foundation damage.  He contracted a Structural Engineer to come out and look at the Drainage Problem and to give him some advice.

Installing Surface Drains in Norman

The Structural Engineer recommended a French Drain to protect and draw water away from the foundation.  He said that “he had recommended French Drain Installation to solve similar problems for homeowners many times in the past.  The Structural Engineer was confident that it would solve the Drainage Problem.

 

Next,

our customer went online and found us by searching under, “ Norman Oklahoma French Drain.”
The Gentleman gave us a call to set up an appointment.  We arrived on the agreed time and provided a (Free- No Obligation- Drainage Diagnostic and Quote) We came out and looked at his Drainage Problem and designed a Drainage System to solve his, Standing-Water Problem.”  We also recommended a surface drain in a corner where water was coming off a steep part of the roof and overwhelming the gutter.

 

Installing a Curb Outlet for a French Drain in Edmond

The customer let us know that he was ready to move forward.  We scheduled the Drainage System Installation for the following week.

When the scheduled day arrived,

we installed the Drainage System.  The Drain was made up of a 6 inch French Drain running 30 feet along the East side of the house.  It curved around the corner of the house.  At that point a 12-inch Surface Drain was connected to the French Drain with 4 inch pipe.  The 6 inch French Drain at that point changed to 6-inch Solid Drainpipe and continued underground 65 feet to a pop-up emitter at the curb in the front yard near the street.

Edmond Oklahoma has been the location for many French Drain Installations for us in the past several years.  Recently we ripped out an old Surface Drain that was under a deck.  The Surface Drain was too small for the job and did not Protect the Foundation from Standing Water. 

 The First step

was to take out part of the deck along the wall.  Next, we took out the Surface Drain and the Three-Inch Pipe which was too small.  Digging a trench along the foundation came next.  We had to ensure the, “Fall” to make sure the water would run from left to right. 

 Next a French Drain Liner needed to be installed.  This was necessary to maintain the integrity of the trench and to keep the French Drainpipe from filling up with sand and getting clogged over the next few years.  Oklahoma Drainage then installed 4-inch ADS Perf/Soc French Drainpipe along the course of the French Drain.  Next, we connected the end of the French Drainpipe to Solid 4 Inch ADS Drainpipe to continue along the trench to the Pop-Up Emitter at the Exit Point.