Leaking Pipe Repair Norman

Oklahoma Drainage and Sprinkler Repair 405 203 9419

Leaking Sprinkler Pipes.

 

Sprinkler pipes may leak for many reasons.  Pipes that are too shallow can freeze and break during the cold of winter.  Repair of PVC Sprinkler pipe in cold temperatures can be difficult.  Frozen Ground is difficult to dig up to get to the damaged pipe.  PVC Glue and Primer don’t bond very well in temperatures that are low.  Even using “Hot Glue,” which is designed to be used in cold temperatures doesn’t always produce the best results.

I use a Heat Gun to warm the new PVC Pipe Fitting so the Hot Glue will bond correctly.  This stops the leak and ensures that the Sprinkler Pipe Repair Will Last.

Fixing a Sprinkler Pipe Leak in cold temperatures can be very difficult.  It takes a person who is willing to get wet when the temperature is below 32 degrees.

Digging in Frozen Ground isn’t easy either.

Oklahoma Drainage and Sprinkler Repair can provide the necessary expertise to handle difficult sprinkler repairs.

Oklahoma Drainage and Sprinkler Repair provides Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

Emergency Sprinkler Repair

Sometimes things go wrong with sprinkler systems.

 

 

One Common problem

is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

 

Inside the valve box is a plastic handle that can turn off the water to the sprinkler system.  It can be blue or red or grey in color.

Many times, the valve box will be full of dirt, and you can’t turn or even see the handle until some of the dirt has been dug out by hand.

 

Water might be shooting up in the air somewhere on your property.  This can be caused by a broken sprinkler pipe or sprinkler valve.

SHUT OFF THE SPRINKLER WATER IF YOU CAN AND GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR. SERVICING ALL OF CENTRAL AND WESTERN OKLAHOMA.

405 203 9419

Servicing Oklahoma City, Norman, Edmond and all of Central and Western Oklahoma

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,     Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

We started with the Valves

The Sprinkler Valves were located in the back yard near the pool.  Six valves were located in one place.  They were very tightly connected in one Manifold.  None of the Sprinkler Valves had worked in a long time.  They were Toro Valves that were over 20 years old.  They all had to be replaced.

Surprisingly there was no shut-off valve for the Sprinkler Water.  The water had to be shut off at the Meter so we could install a Manual Shut off valve.  Once installed, the water was turned back on that ran to the house.   The water that ran to the Sprinkler System was shut off with our New Shut Off Valve.

The Sprinkler Valves Were Removed

Now, the 6 valves had to replaced.  The valves that were used were made by Rain Bird.  Before we began, I had to talk to the Customer.  The previous valve design was a bad idea to repeat.

The original Sprinkler Valves were crammed into one large valve box in one very tight manifold.  This is bad because the valves were too close to the fittings.  Simply put, if one valve had to be replaced or worked on in the future, all 6 valves had to be taken out and replaced.   If one valve was bad and 5 worked fine, they all still had to be replaced.

That’s Stupid!

I recommended that an additional Valve Box be installed putting 3 valves in each Valve Box.  This would allow plenty of space between the valve fittings.  If one Sprinkler Valve had to be adjusted or replaced in the future, the other 5 valves need not be disturbed.  Simple Enough!

Check For Leaks

Once the valves were replaced and working, it was time to turn on each Sprinkler Zone, one at a time.  Water was shooting up from the ground in several places in zone 1.  Two broken Sprinkler Pipes and 5 bad Sprinkler Heads in zone 1 had to be fixed and replaced.  We went through each of the 6 zones in similar fashion fixing lots of leaks and replacing bad sprinkler heads.  After that the sprinkler system worked like new.

The Sprinkler Repair Cost About Half of the Cost of Completely New System.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Spraying Rotor Sprinkler Repair

Spraying Rotor Sprinkler Head

Countless Sprinkler Controllers have been Reprogramed or Replaced.

Sprinkler Head Adjustment is a service provided by Oklahoma Drainage and Sprinkler Repair.  We have adjusted sprinkler heads since 1993.

Many times, Sprinkler heads get, “Out of Wack.”  Lawn mowers and weed eaters are notorious for this.  Sprinkler heads start spraying water in the wrong place.  It is frustrating to water concrete while plants and grass go without moisture.

Pop-Up Sprinkler Heads

Pop-Up Sprinkler Heads can be adjusted several ways.  How far water goes to the left or right can be increased or decreased.  The distance the water goes can also be increased or decreased.  Finally, how high a sprinkler head pops up can be increased or decreased by installing a taller or shorter head.

Sometimes sprinkler heads spray a reduced distance and don’t perform very well due to water scale.  Minerals in the water can completely clog a Pop-Up.  Usually, the sprinkler nozzle on top of the sprinkler head, need only be replaced without replacing the entire head.

Rotor Sprinkler Heads also can be adjusted to the left or right.  Spray Distance can be increased or decreased as well.

Needs Change

What’s going on in your yard can change.  This calls for Sprinkler Head Adjustment.  Adding or removing a swimming pool changes everything concerning sprinkler heads.  Any number of things can change the necessary sprinkler head coverage.

 

 

Oklahoma Drainage and Sprinkler Repair — Installing – French DrainsSurface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler RepairBroken Sprinkler Pipes Sprinkler Head AdjustmentSprinkler Valve Replacement

We provide Service for Folks in: Norman, Oklahoma City, Edmond, and Moore.

Central and Western Oklahoma is our Service Area since 1993.  

                                                           (405) 203-9419

Check out Sprinkler System Check-Up

 

Gutter Connection to French Drain.  Oklahoma Drainage Recommends connection of Gutter Downspouts to French Drains where possible.

Water coming from the Gutter Downspout is moving faster than the water already in the French Drain.  It causes suction in the French Drain Behind the Gutter.  The additional suction causes the French Drain to work even better than normal, moving more water faster.  This is called the ” Bernoulli Principle.”

French Drains are Designed to protect foundations.

What is a French Drain? Click if you arent sure.

This puts the French Drain in close proximity to Gutter Down Spouts.  Rather than have water come off the roof and out the Down Spout and on to the ground below, many times it is much better to tie a Gutter Down Spout Directly into a French Drain or nearby Drainpipe depending on the Drainage System Design.

Connecting The Down Spouts

Directly into a French Drain is much more efficient and causes suction to occur in the French Drain.  Connection of Gutter Down Spouts to a French Drain makes the Drainage System work better.

Connecting Gutter into French Drain System

Oklahoma Drainage– We install French Drains, Channel Drains, Surface Drains, Sump Pumps and Sod.

If You live in Oklahoma City and water damaging your foundation, we can install a French Drain for you.  Quotes are Free.

If you live in Norman and have water standing on your driveway, we can install a Channel Drain for you.  Quotes are Free.

If you live in Edmond and have water flooding your basement, we can install a Sump Pump for you.  Quotes are Free.

If you live in Moore and have water washing out your flower bed mulch, we can install a Surface Drain for you.  Quotes are still free.

If you live in Yukon and need grass to grow, we can install Sod too!

Servicing All of Central and Western Oklahoma Since 1993.

FRENCH DRAIN CONNECTED TO GUTTERS

Many different types of Drains can be hooked together by one Drainpipe.  The Drainpipe then running to an Exit Point makes up a Drainage System.

One common type of Drain used in a Drainage System is A “French Drain.”

Sometimes, a French Drain is installed close to a building foundation or in a low area next to a home or business.  This puts the French Drain in close proximity to Gutter Down Spouts.

Rather than have water come off the roof and out the Down Spout and on to the ground below, many times it is much better to tie a Gutter Down Spout Directly into a French Drain or nearby Drainpipe depending on the Drainage System Design.

Gutter Downspouts

Connecting The Down Spouts Directly into a French Drain is much more efficient and causes suction to occur in the French Drain.  Connection of Gutter Down Spouts to a French Drain makes the Drainage System work better.

French Drain Installation

Gutter connected to French Drain.

 

Oklahoma City Sump Pump Contractor

Sump Pumps are used when water can’t be drained away by gravity.  You might have water standing in an area and it is up hill in all directions.  A gravity flow French Drain or Surface Drain System will not work so you must pump the water to the Exit Point.  The Same holds true if you have water standing in a basement.  Pumping out the water is the only way.

Most Sump Pumps work automatically.  When the Sump Pump is under water a float rises up on the side of the pump and turns on the pump.   Once the water is pumped away, the float falls back down and turns off the pump.  When water is flowing constantly on to the pump, it turns itself on and off over and over.  This could go on for hours or even days.

Sump Pump Inside Sump Cavity

Sump Pump Inside Sump Pump Cavity

Two Sizes of Sump Pumps

Pump Size refers to how powerful it is not how physically large it is.  For Home or Small Business use a 1/3 Horse or a 1/2 Horse Works Best.  Larger Pumps such as a 1 Horse Pump must be ordered by a supplier and must be Hard Wired to 220 voltage by an electrician.

A Sump Pump Cavity

looks like a trash can.  When water drains into the sump cavity it raises the float and turns on the pump. Once empty it falls down and turns off the Pump.

The larger the sump cavity the less often the sump turns on and off.   A small sump cavity wears out the sump pump faster because it turns on and off more making it less efficient.

 

 

Large volume

custom sump cavities collect a large volume of water before the sump pump turns on.   Once on the Sump pump works for several minutes before turning off.  Once empty the larger sump cavity takes a longer time to refill again.  Which gives the pump a longer time to cool off and rest.

A sump pump in a large cavity will last much longer than one in a small cavity.

Installing Sump Pump

Oklahoma Drainage recently diagnosed a Drainage Problem in South Oklahoma City.

The Homeowner had a sump Pump in their basement that was fed from a French Drain outside the Basement Wall.  The French Drain was 14 feet down along the Stem wall of the house.  The French Drainpipe was cheap and had collapsed.  We brought in a Mini Excavator and dug up the pipe and replaced it with Durable ADS 4 inch perf/soc French Drainpipe.  In the end, we were able to dig up the pipe and replace it.

Next, we installed a new exit for the water by installing a curb fitting.

No more flooding in the customers basement.  A few weeks later our customer was able to lay carpet in the basement with no problems.

Sump Pump Installation is necessary when water from a Drainage System can’t flow properly.  This means it is uphill in every direction from the Drain Intake.

 

 

Norman French Drain Specialist.  Oklahoma Drainage and Sprinkler Repair provide French Drain Installation, and French Drain Service for Central and Western Oklahoma.

We install French Drains to protect Foundations.  If you need a French Drain along your driveway, we do that too.  A French Drain might be needed in a yard or flowerbed.  French Drains solve standing water problems and provide limited protection for flooding.

Oklahoma Drainage and Sprinkler Repair 405 203 9419 — We provide:

    French Drain Installation, Surface Drain Installation, Drainage System Installation

    Sprinkler Repair for all aspects of Residential Sprinkler Systems

French Drain Running Through Low Areas

French Drain with stepping stones

WHAT SIZE DRAINPIPE FOR FRENCH DRAINS?

French Drains can be decorated with many types of stone

French Drains can be decorated with many types of stone

French Drains

can utilize several types and sizes of French Drainpipe.  An older type that is not commonly used any more is 4-inch PVC Pipe with large half inch holes drilled in the Pipe.

This doesn’t work very well, Because the holes are too large and the number of holes in the French Drainpipe are too few.  Also there is no filter or “Soc” around this particular French Drainpipe.  If it is used in sandy or loose soil the holes will clog and the pipe will fill up with sand.  PVC French Drainpipe should be avoided.

ADS French Drainpipe is much better; the holes are smaller and much more numerous.  It also comes inside a soc that acts as a filter and helps keep sand and debris out of the French Drainpipe.  It works very well.

For Small business and Residential French Drains, four inch ADS Perf/Soc French Drainpipe is adequate and the most common.  It is used for the majority of all French Drains installed.  French Drains can be installed using 3 inch ADS Perf/Soc but many times it is too small and can be overwhelmed by a heavy rain or from a bad design.  (Too many gutter down spouts connected directly into the French Drain, For Example) Three Inch French Drainpipe should be avoided if possible.

Information on French Drains

Edmond is one of the communities in Central Oklahoma that Oklahoma Drainage services.  We have installed almost a thousand French Drains in the Edmond community in the past 31 years.

Edmond has many hills and valleys.  Neighborhoods are built on hillsides.  This causes many Drainage Problems.  We have installed French Drains by themselves and as a part of Drainage Systems to protect Driveways, Sidewalks, Foundations all over Edmond.

French Drains may be installed in Flower Beds or grassy areas too. A  French Drain  when installed correctly can provide many years of property protection and Piece of Mind.

WHERE WE HAVE WORKED!

In 1993 we had no website.  I stuck little signs on the side of the road as advertisement.  I got my first Drain Installation work in March of 1993 in Norman.  It was in Brookhaven North of Robinson Street on the West side of I 35.

Over the years Oklahoma Drainage and Sprinkler Repair has installed all types of Drainage Systems in almost Every town in Central and Western Oklahoma.

The majority of our customers live in Oklahoma City, Norman, Edmond, Yukon, Mustang, Moore, Midwest City, Del City, Blanchard, New Castle, Yukon and Choctaw.

Oklahoma Drainage and Sprinkler Repair hasn’t been limited to those areas, however.  We have also installed French Drains, Surface Drains, Channel Drains, and Sump Pumps in many other cities.

Working Drainage Systems Installed by Oklahoma Drainage also reside in: Lawton, Duncan, Ardmore, Chickasha, Shawnee, Enid, Weatherford, Elk City, El reno and many other places.

If you live in any of these Cities or towns, we have installed a French Drain, Surface Drain, Channel Drain, or Sump Pump within 5 miles of your home.

French Drain and Surface Drain

French Drain and Surface Drain

Here is a description of other recent work.

A little bit North of Downtown Oklahoma City, Oklahoma Drainage installed a 6-inch French Drain between two businesses which were less than three feet apart.  The French Drain went between a Law Firm and a Tire shop.  Water was leaking through the walls of both businesses.  Gutters between the two establishments were dumping a huge amount of water.  We installed a 6-inch French Drain between the gutters.

It took a long time to get the dirt out of the trench for the French Drain.  It was a very tight fit.  We had to use a little red wagon to haul out the dirt for the French Drain and haul back in the crushed limestone for the French Drain.  It looked a little silly, but it was the only thing we could find that was narrow enough to fit between the buildings.  A French Drain that normally would take 1 day to install took three.

Double Exit Point

The French Drain had a Double Exit Point.  This means that once water entered the French Drainpipe, it could run South to the street, or it could run North to the alley.  To exit points greatly increases the water capacity for any French Drain.

Along the course of the French Drain, we connected two large gutters directly into the Drainpipe.

Once in place, the French Drain eliminated all the water that was leaking into the two buildings.

Drainage Problem Solved!

 

French Drain Answers are a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

Oklahoma Drainage and Sprinkler Repair — Installing – French DrainsSurface DrainsChannel DrainsSump Pumps.

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes Sprinkler Head AdjustmentSprinkler Valve Replacement

We provide Service for Folks in: Norman, Oklahoma City, Edmond, and Moore.

Central and Western Oklahoma is our Service Area since 1993.  

                                                           (405) 203-9419

 

French Drain Installation —

French Drains are designed to do a lot of things.  If you have an area that has unwanted water standing in it or running across it, a French Drain can be the answer.  A French Drain is a trench that runs across the Drainage Problem Area.  A French Drainpipe is placed in the bottom of the trench.

 

The French Drainpipe

is perforated with thousands of small holes.  In most cases the Drain Pipe has a nylon soc around the pipe to act as a filter for the French Drain.  The French Drain trench is then filled with some type of small rock or stone.  We  typically uses crushed 1 inch Lime Stone to cover the French Drain Pipe.  The dirt that was dug out of the trench is taken away or spread out around the French Drain.  The Lime Stone replaces the dirt and fills the French Drain Trench all the way to the surface.

 

When water come in contact with the French Drain, it seeps down through the stones and into the French Drainpipe.  It then flows through the Drainpipe to the exit point.  Typically, a French Drain will have two possible exit points.   The First is called a “Pop-Up Emitter.”  It is a Green Lid on top of a release basin for the French Drain.

 

Oklahoma Drainage  — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps

Servicing all of Central and Western Oklahoma since 1993.

When Installing a French Drain as part of a Drainage System, there are many things to consider.

What is the primary source of water coming into the problem drainage area.

Are there secondary sources of water entering the area.

What are they and how many.

How fast does water enter the area and how often.

What are the potential exit points for the water,  Where do we want to take the water too.  Is there more than one potential exit point to increase drainage capacity.

Does the customer want a Drainage System or a Flood Prevention System and does he understand the difference.

 

Oklahoma Drainage

recently diagnosed a Drainage Problem in  South Oklahoma City.  The Home owner had a sump Pump in their basement that was fed from a French Drain outside the Basement Wall.  The French Drain was 14 feet down along the Stem wall of the house.  The French Drain Pipe was cheap and had collapsed.  We brought in a Mini Excavator and dug up the pipe and replaced it with Durable ADS 4 inch perf/soc French Drain pipe.  In the end, we were able to dig up the pipe and Replace it.

New Trench for French Drain

Next we installed a new exit for the water by installing a curb fitting.

No more flooding in the customers basement.  A few weeks later our customer was able to lay carpet in the basement with no problems.

French Drain Installed Along Stem Wall

Oklahoma Drainage — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps

Servicing all of Central and Western Oklahoma since 1993.

French Drain Installation

Oklahoma Drainage and Sprinkler Repair has been diagnosing and solving Drainage Problems since 1993.  Water has the ability to get into places around your home where you really don’t want it to be.  Some drainage problems are easy to solve.  Typically water enters the problem drainage area one way from one source.  The really tricky drainage problems occur when water enters the problem drainage area from multiple directions and from multiple sources.  Sometimes a secondary water source can’t be seen or identified until the primary water problem source is eliminated.

An example of this occurs when water is running into a problem area in an obvious way over the ground where you can see it.

Simple enough.

A drainage system is installed with a surface drain as the “intake” with drainage pipe running to an exit point.  Initially the water drains away and everything looks great.  The next day water is back and is all around the surface drain, but below the edge and it hasn’t rained at all, so no additional water ran over the surface of the ground to flood the area.

The primary water source was solved, ( The surface water run off ) but the secondary water source was not.  Which was sub-surface water, (ground water) running into the area.  A surface drain can’t drain “ground water.”  A French Drain should have initially been installed instead of a Surface Drain.  A French Drain can drain both Surface Water and Ground Water.

 

Six inch ADS Perf/Soc French Drainpipe is usually a good idea when possible.  It carries a much larger volume of water.  Six Inch French Drains are rarely overwhelmed.

The Drawbacks to 6-inch French Drain installation are:

 
 1.  The Materials Cost is higher for six-inch French Drain Compared to Four Inch Pipe.
                                                                                                                   
2.  Many times 6 Inch French Drainpipe is too large for many applications, Such as going under a fence or sidewalk.  
                                                                                                                   
3.  The trench for a 6 inch French Drain must be much larger than a 4 Inch
                                                                                                                 
 4.  The amount of gravel or limestone or River Rock used to Cover the 6 inch French Drain is Much larger
 
All things being considered, the performance and longevity of a 6-inch French Drain is well worth it if you are trying to protect something of value to you!  If the higher cost and the additional labor and materials are not a problem and 6-inch French Drainpipe is not too big for what you want to do then a 6-inch French Drain would be the best.  
 
 
 
 

Oklahoma City Channel Drain Installation, Oklahoma City French Drain

French Drain Installation, Drainage Systems, Surface Drain, Sump pumps, –

Driveway Drain, Channel Drain, Sidewalk Drain Installation, Oklahoma City, Edmond, Norman, Moore

DRAINS INSTALLED IN CONCRETE

Standing Water on a Driveway or Sidewalk can be a real pain.  Stepping out of your car into standing water is no fun.  Many times, a channel drain can solve this kind of problem.

Channel Drains are usually set in concrete.   Many times standing water requires that a new drain be set in  concrete.  This requires that the concrete be cut and removed and a drain installed in its place with new concrete around the edges.

Obliviously Skill, Expertise, and Experience is required to make a big cut across a driveway or sidewalk.

Oklahoma Drainage

Before

After

channel drain driveway

If a channel drain is installed correctly, it is very strong.  A car can be driven over it.

Channel drains are of two kinds, Metal or Composite.

Metal Channel drains can be Crome, Cast Iron, or Stainless Steel.

A Composite Channel Drain is made up of very tough plastic combinations.

Composite Channel Drains seem to be the most durable and easiest to service.

Oklahoma City Channel Drain

Oklahoma Drainage and Sprinkler Repair

Channel Drain Installation is a primary focus for Oklahoma Drainage and Sprinkler Repair.  We have been installing Channel Drains as part of Drainage Systems since 1993.   We also install Surface Drains, French Drains, and Sump Pumps to fit our customer’s needs.

NDS Grey Composite Channel Drain Running Across Driveway Connected to 4 Inch ADS Solid Drain Pipe

NDS Grey Channel Drain Running Across Driveway
in Edmond

Channel Drain Installation Is a Central Focus for Oklahoma Drainage.  We have been Installing Channel Drains set in Concrete since 1993.

Channel Drain Set in Concrete

Channel Drains can look great and be very functional and durable.

However, A Channel Drain is not an easy thing to install!  It takes a great deal of precision, Experience, and Attention to Detail.  This is Definitely Not something to allow your Landscape Company to attempt, or your Brother-In-Law!

Just because someone is skilled at pushing a mower around, doesn’t mean you should let them cut across your driveway with a concrete saw.

I get a lot of business fixing and replacing Drains of all types that were installed incorrectly by landscape companies and armatures.  Typically, they stick to messing up French Drains, but I have fixed Channel Drains that were an absolute “Train Wreck!” as well.

 

Oklahoma Drainage 405 203 9419

French Drain Installation, Channel Drain Installation Surface Drain Installation, Drainage System Installation, 

 

 

 

A Drainage System is made up of three parts.  An Intake, a transition, and Exit.

An intake is a Drain or a group of Drains that brings water into the Drainage System.  It can be a French Drain, Surface Drains, Channel Drain, or Sump Pump.

A Drainage System can have one intake or several.  If more than one, it can be any combination of French Drains, Surface Drains, Etc.

For Example: You might have a Surface Drain set in your sidewalk and a Channel Drain next to your driveway and a French Drain in your yard.  They all connect to each other through drainpipe and feed water into the Drainage System.

The Transition

The Transition is the Drainpipe that takes the water to the exit point.  It can be a large pipe or small depending on how much water needs to be moved and how fast it needs to drain.  More than one Drainage Exit Point.  This increases the amount of water that the Drainage System can move.

Back-Flow-Valve Service, Sprinkler Repair

Oklahoma Drainage and Sprinkler Repair Provides Service for Back-Flow-Valves and all types of Lawn Sprinkler Repair and Service.  We have provided Expert Service for all of Central and Western Oklahoma Since 1993.

Back-Flow-Valves

There are two types of Back-Flow-Valves.

Above Ground

Above Ground Back-Flow-Valve

Above Ground Back-Flow-Valve.

 

Below Ground Back-Flow-Valve.

Below Ground Back-Flow-Valve

Below Ground Back-Flow-Valve

What is a Back-Flow-Valve?

A Back-Flow-Valve is a part of a Lawn Sprinkler System.  Water passes through it from the water source which can be a Water Meter or a Well Pump.  It forces water to travel in only one direction from the source to the sprinkler system.  It can’t travel backward back to the water source which again is a water meter or well pump.

A Back-Flow-Valve provides protection to the water source from back pressure and chemical contamination from lawn fertilizer.

Most Cities require a Back-Flow-Valve as “Code” for Sprinkler Installation.

Emergency Shut off

Back-Flow-Valves usually have an Emergency Shutoff valve on them that can shut off the water to the lawn sprinkler system but keep the water turned on to the home. Most Back-Flow-Valves have two Emergency Shut off Handles.  Either one will work.  Many times, they are hard to turn, however.

If there is a leak or water is shooting up in the air just turn the valve handle and give us a call.

In ground Back-Flow-Valve

Blue Emergency Shutoff handles for a Back-Flow-Valve.

Norman Sprinkler Checkup is a Central Focus for Oklahoma Drainage.  We Performed or first Sprinkler Repair in Norman in 1993.  It was in Brookhaven on the West side of Norman.

Recently we had a customer in Oklahoma City who wanted to move his Sprinkler Valves.  They were in a bad place in his flower bed.  He wanted to plant a tree where the valves were located.

We moved 4 Sprinkler Valves about feet out into the yard.  All the Sprinkler Pipes had to be redesigned and installed matching the new location and maintaining full functionality.

 

What Is a Sprinkler Valve?

Think of a Sprinkler Valve as an “Off or on” Switch.    The Sprinkler Controller   turns the valves on or off.

It Sends a signal through a wire which is underground to the sprinkler valve somewhere in your yard.

Once turned on, the valve lets water pass through a sprinkler pipe to a specific group of sprinkler heads called a Sprinkler Zone.  The controller allows water to reach the sprinkler heads for a certain amount of time running through the sprinkler valve.  Once the time is up, it shuts off the sprinkler valve and moves on to the next valve in sequence.

Think of it as walking into every room in your house one at a time.  As you enter you turn on the light.  As you leave you turn off the light and move to the next room. You are the controller.  The light switch represents the sprinkler valve.

Rainbird Sprinkler Valve

Rainbird Sprinkler Valve

The Sprinkler Valve in the picture above was taken out of the ground after the pipe froze and broke on the right side.  You can see the crack in the PVC pipe.  Of course, I had to clean all the mud off the valve before I took the picture.

What causes a Sprinkler Valve to stop working?

Like anything else, a sprinkler valve can wear out.   Sprinkler valves fail in closed position.  It won’t run continuously if it breaks.

Sprinkler Valves get stuck while running sometimes.   The water supply must be then turned off to stop the Sprinkler from running.

Sprinkler Valves can freeze and break in the winter if the sprinkler system has not been properly drained for winter’s cold.

(winterized)

Tree roots can twist or break sprinkler pipes running into sprinkler valves.  Magnolia Trees are really bad about this.  Oak trees can cause damage too.

Driving something heavy across your yard can crush sprinkler valves.  Usually riding lawnmowers don’t cause damage but any truck or car will if you drive over a valve.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provides Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

Emergency Sprinkler Repair

Sometimes things go wrong with sprinkler systems.

 

IF YOU NEED HELP IN THE MIDDLE OF THE NIGHT OR ON A WEEKEND WITH YOUR SPRINKLER SYSTEM, GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR.  405 203 9419

IT MAY TAKE A FEW HOURS FOR US TO GET THERE BUT WE WILL COME TO HELP.

 

One Common problem is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

Grass Growing Over a French Drain can be a good thing.  Let Oklahoma Drainage and Sprinkler Repair tell you why!

French Drain Installation in sun or shade.  Oklahoma Drainage and Sprinkler Repair can show you the difference.

Oklahoma Drainage– We install French Drains, Channel Drains, Surface Drains, Sump Pumps and Sod.

If You live in Oklahoma City and water damaging your foundation, we can install a French Drain for you.

 Or If you live in Norman and have water standing on your driveway, we can install a Channel Drain for you.

If you live in Edmond and have water flooding your basement, we can install a Sump Pump for you.

 Or If you live in Moore and have water washing out your flower bed mulch, we can install a Surface Drain for you.

If you live in Yukon and need grass to grow, we can install Sod too!

Servicing All of Central and Western Oklahoma Since 1993.

 

FRENCH DRAIN INSTALLATION IN SUN OR SHADE?

French Drain Running Through Low Areas

Rest Home French Drain Running Through Low Areas

 

French Drains are designed to cover large areas and move lots of water.  During a hard rain, water will seep down through the gravel and into the Perforated French Drainpipe that is buried under the gravel.  The water fills into the pipe and moves downhill to the desired Exit Point.  French Drains like the one in the picture above that are in the sun most of the day will have grass that overgrows the limestone.  The gravel will disappear over time.

Grass will Grow Over the Gravel

The French Drain will continue to work even after the grass has grown over it.  A “Thatch Filter ” is made up of the grass that covers the French Drain.  The French Drain then has two filters.

First is the Neo-Prene Soc that comes around the Perforated French Drainpipe.  Later when the grass grows over it, the French Drain then has a second Thatch Filter.  This ensures that the French Drainpipe won’t clog over time with dirt, sand, or debris.  This only works with grass that does well in the sun like Bermuda or Tift.

Shade Grasses won’t grow up and through French Drain gravel.

YOU DON’T WANT TO COVER THE FRENCH DRAIN WITH DIRT.  IT WILL GREATLY REDUCE THE DRAINAGE PERFORMANCE OF THE FRENCH DRAIN.  IT DEFEATS THE ENTIRE REASON FOR THE FRENCH DRAIN.  IF YOU DON’T LIKE THE WAY IT LOOKS AND CAN’T BE PATIENT ENOUGH TO WAIT UNTIL THE GRASS GROWS THROUGH IT IF IT IS IN THE SUN, THEN DON’T INSTALL IT AT ALL.

IF THE FRENCH DRAIN IS INSTALLED IN THE SHADE, YOU CAN USE DECORATIVE ROCK TO MAKE A FOOT PATH OR ROCK GARDEN ON TOP OF IT.  YOU ARE ONLY LIMITED BY YOUR IMAGINATION.

 

Lawn Sprinklers can have pipes that leak.   PVC Pipe is the most common Sprinkler System Pipe and leaks definitely are possible.

Leaking Sprinkler Pipes

Leaks can occur near Sprinkler Valves.  Water travels through Sprinkler Valves and can leak going in or coming out.

Many Cities require a back-flow valve to protect the City’s water supply.  It can also leak as water passes through the valve.

Leaks can also occur due to tree roots stressing Sprinkler Pipes.  The pipes can be twisted by roots and crack or break.

Water inside Sprinkler Pipes can freeze and break or crack the PVC Pipe.

Move sprinkler heads, Norman, Oklahoma City, Edmond

There are many reasons for moving Sprinkler Heads.

If you put in a new pool, most of the sprinkler heads will need to be moved.

Sprinkler Heads need to be moved if you have new landscaping installed.

Sometimes Sprinkler Heads weren’t in a good place to begin with.  They need to be moved!

Oklahoma Drainage and Sprinkler Repair can help.  We have been moving Sprinkler Heads since 1993.

In 32 years, we have moved a lot of Heads for Customers in Central and Western Oklahoma.

 

Oklahoma Drainage and Sprinkler Repair provide Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

Sprinkler Head Installation

Moving Sprinkler Head

Spraying Rotor Sprinkler Repair

Spraying Rotor Sprinkler Head

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,   Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

We started with the Valves

The Sprinkler Valves were located in the back yard near the pool.  Six valves were located in one place.  They were very tightly connected in one Manifold.  None of the Sprinkler Valves had worked in a long time.  They were Toro Valves that were over 20 years old.  They all had to be replaced.

Surprisingly there was no shut-off valve for the Sprinkler Water.  The water had to be shut off at the Meter so we could install a Manual Shut off valve.  Once installed, the water was turned back on that ran to the house.   The water that ran to the Sprinkler System was shut off with our New Shut Off Valve.

Rainbird Sprinkler Valve

Rainbird Sprinkler Valve

The Sprinkler Valves Were Removed

Now, the 6 valves had to replaced.  The valves that were used were made by Rain Bird.  Before we began, I had to talk to the Customer.  The previous valve design was a bad idea to repeat.

The original Sprinkler Valves were crammed into one large valve box in one very tight manifold.  This is bad because the valves were too close to the fittings.  Simply put, if one valve had to be replaced or worked on in the future, all 6 valves had to be taken out and replaced.   If one valve was bad and 5 worked fine, they all still had to be replaced.

That’s Stupid!

I recommended that an additional Valve Box be installed putting 3 valves in each Valve Box.  This would allow plenty of space between the valve fittings.  If one Sprinkler Valve had to be adjusted or replaced in the future, the other 5 valves need not be disturbed.  Simple Enough!

Check For Leaks

Once the valves were replaced and working, it was time to turn on each Sprinkler Zone, one at a time.  Water was shooting up from the ground in several places in zone 1.  Two broken Sprinkler Pipes and 5 bad Sprinkler Heads in zone 1 had to be fixed and replaced.  We went through each of the 6 zones in similar fashion fixing lots of leaks and replacing bad sprinkler heads.

The Sprinkler Repair Cost About Half of the Cost of Completely New System.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

Sprinkler Head Adjustment is a service provided by Oklahoma Drainage and Sprinkler Repair.  We have adjusted sprinkler heads since 1993.

Many times, Sprinkler heads get, “Out of Wack.”  Lawn mowers and weed eaters are notorious for this.  Sprinkler heads start spraying water in the wrong place.  It is frustrating to water concrete while plants and grass go without moisture.

Pop-Up Sprinkler Heads

Pop-Up Sprinkler Heads can be adjusted several ways.  How far water goes to the left or right can be increased or decreased.  The distance the water goes can also be increased or decreased.  Finally, how high a sprinkler head pops up can be increased or decreased by installing a taller or shorter head.

Sometimes sprinkler heads spray a reduced distance and don’t perform very well due to water scale.  Minerals in the water can completely clog a Pop-Up.  Usually, the sprinkler nozzle on top of the sprinkler head, need only be replaced without replacing the entire head.

Rotor Sprinkler Heads also can be adjusted to the left or right.  Spray Distance can be increased or decreased as well.

Needs Change

What’s going on in your yard can change.  This calls for Sprinkler Head Adjustment.  Adding or removing a swimming pool changes everything concerning sprinkler heads.  Any number of things can change the necessary sprinkler head coverage.

 

 

Oklahoma Drainage and Sprinkler Repair — Installing – French DrainsSurface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler RepairBroken Sprinkler Pipes Sprinkler Head AdjustmentSprinkler Valve Replacement

We provide Service for Folks in: Norman, Oklahoma City, Edmond, and Moore.

Central and Western Oklahoma is our Service Area since 1993.  

                                                           (405) 203-9419

Check out Sprinkler System Check-Up

 

 

IF YOU NEED HELP IN THE MIDDLE OF THE NIGHT OR ON A WEEKEND WITH YOUR SPRINKLER SYSTEM, GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR.  405 203 9419

IT MAY TAKE A FEW HOURS FOR US TO GET THERE BUT WE WILL COME TO HELP.

 

One Common problem is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

 

Inside the valve box is a plastic handle that can turn off the water to the sprinkler system.  It can be blue or red or grey in color.

Many times, the valve box will be full of dirt, and you can’t turn or even see the handle until some of the dirt has been dug out by hand.

 

Water might be shooting up in the air somewhere on your property.  This can be caused by a broken sprinkler pipe or sprinkler valve.

SHUT OFF THE SPRINKLER WATER IF YOU CAN AND GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR. SERVICING ALL OF CENTRAL AND WESTERN OKLAHOMA.

405 203 9419

Servicing Oklahoma City, Norman, Edmond and all of Central and Western Oklahoma

 

 

Cell phone Sprinkler Controller.  Oklahoma Drainage and Sprinkler Repair can Install a new Sprinkler Controller that can be run by an App on your phone.

If you are a long way from home and need to turn your Sprinkler System on or off just pick up your Cell Phone.  There are different brands including Rainbird that have this capability.

Sprinkler Controller

Installing New Sprinkler Controller with Cell Phone connection.

If you look in the picture above on the left side, you can see the Cell Pone Hardware connected into the Accessory Port.

Oklahoma Drainage and Sprinkler Repair 405 203 9419 — We provide:

    French Drain Installation, Surface Drain Installation, Drainage System Installation

    Sprinkler Repair for all aspects of Residential Sprinkler Systems

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR, Provides Expert Sprinkler Repair for:  Sprinkler Valves, Sprinkler Heads, Sprinkler Controllers, and the most common problem, Sprinkler Pipes or Sprinkler Leaks.

Sprinkler Repair Service is provided for: Oklahoma City, Norman, Edmond, Yukon, Mustang, Moore, Midwest City, Blanchard, New Castle, and all surrounding areas.

Sprinkler Repair is also very popular this time of year.  Folks in Oklahoma are turning on their Sprinkler Systems and discovering problems. It has been busy.

We fixed several leaks in a Sprinkler System in Edmond.  The Sprinkler pipes were leaking in several places.  Each leak had to be cut out and replaced.  The Sprinkler System was fairly new.  It was installed last summer by a Pool Company that also installs cheap sprinkler systems.

All the joints in the sprinkler pipes were glued together with clear PVC Cement.  That part is OK, but they cut some corners and didn’t use PVC Primer with the glue.  As a result, the joints didn’t bond very well and many of them blew apart this spring when the sprinkler systems were turned on.  (Thus, all the leaks) I suspect we will have to go back several times to fix additional leaks.  We can only warranty the PVC joints that we have replaced.   Cheaper isn’t always better.

Sprinkler Controller

Sprinkler Controller

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR

Servicing Central and Western Oklahoma since 1993.

Sprinkler RepairFrench Drain InstallationDrainage System Installation

This week Oklahoma Drainage and Sprinkler Repair overhauled a flowerbed Sprinkler Zone in a Sprinkler System in East Norman.

The homeowner had an existing Sprinkler System that was in good shape for the most part but had problems with the flowerbed Sprinkler Zone.

It had a Drip Sprinkler Zone installed.  The Drip Sprinkler System was installed correctly but was not practical for the flower bed.

The flowerbed was very sandy and could not retain water very well even with good mulch.  Plus, the surrounding brick walls increased the amount of heat the plants had to endure in the summer.  The Drip Sprinkler Zone could not provide enough water fast enough for the plants.

We provide:

1.  Sprinkler Valve Problems

2.  Sprinkler Wiring Problems

3.  Sprinkler Controller Problems / Sprinkler Clock Problems

4.  Sprinkler Head Problems

5.  Sprinkler Pipe Problems

6.  Sprinkler Coverage Problems

7.  Sprinkler Redesign Problems for new fences or swimming pools.

If you have water running down the street in the middle of the night because your sprinkler system is leaking or won’t shut off, give Oklahoma Drainage and Sprinkler Repair a call.  405 203 9419

Sprinkler Repair

is a central focus for Oklahoma Drainage and Sprinkler Repair.  Just like any car or home, a lawn sprinkler system must be updated and maintained.  Typically, people wait till spring to get the kinks worked out of their sprinkler system.

Sprinkler Repair is an ongoing issue for any sprinkler system.  Folks in Central Oklahoma are turning on their Sprinkler Systems and discovering problems.

We fixed several leaks in a Sprinkler System in Edmond.

The sprinkler pipes were leaking in several places.  Each leak had to be cut out and replaced.

The Sprinkler System was fairly new.  It was installed last summer by a Pool Company that also installs cheap sprinkler systems.

All the joints in the sprinkler pipes

were glued together with clear PVC Cement.  That part is OK, but they cut some corners and didn’t use PVC Primer with the glue.  As a result, the joints didn’t bond very well and many of them blew apart this spring when the sprinkler systems were turned on.  (Thus, all the leaks) I suspect we will have to go back several times to fix additional leaks.

We can only warranty the PVC joints that we have replaced.   Cheaper isn’t always better.

Today we did a sprinkler repair in Norman.  The sprinkler system needed a checkup.  We went through each sprinkler zone and identified several different problems.  Zone 2 had a cracked sprinkler pipe in a flower bed.

Next, Zone 4 had a broken sprinkler rotor on the edge of the driveway that had been driven over and broken.  Zone 6 and 7 each had a couple of pop-up spray heads that were worn out and would not pop-up.  The diagnosis and the repair took less than two hours.  Now their sprinkler system is running great!

Don’t Wait!

I can tell you this, DON’T WAIT TILL MARCH TO GET YOUR SPRINKLER SYSTEM IN SHAPE.  BY APRIL THERE WILL BE A FLOOD OF PEOPLE TRYING TO GET BROKEN SPRINKLER HEADS FIXED OR NEW SPRINKLER CONTROLLERS INSTALLED OR LEAKING BACK-FLOW VALVES REPLACED.

CONSIDER GETTING YOUR SPRINKLER REPAIR WORK DONE ANY TIME OTHER THAN THE SPRING.  FOR THOSE OF YOU WHO HAVE NO CHOICE AND MUST HAVE WORK DONE IN THE SPRING, SCHEDULE AS EARLY AS YOU CAN.

OUR SPRINKLER REPAIR WORK IS TOP QUALITY AND OUR PRICES ARE FAIR.  IT IS OUR GOAL TO GET TO CUSTOMERS QUICKLY IN MARCH AND APRIL, WHILE MAINTAINING OUR QUALITY OF WORK.

 

Oklahoma Drainage and Sprinkler Repair

can help if you need to re-design your Sprinkler System.  If for example you are adding a swimming pool in your back yard, we can move the Sprinkler Heads and Sprinkler Pipes to fit the new dimensions of your yard.  We can redesign or add-on to sprinkler systems where the homeowners need change.

Maybe you don’t need a large part of your sprinkler system redesigned.  You May just want a few heads moved to new locations.

Whatever your Sprinkler needs may be, Oklahoma Drainage and Sprinkler Repair can help.  Give us a call at : 405 203 9419

 

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provides Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

Sprinkler Repair for us is very clear.  We have been doing it a long time and have become very good at it.  Many times, we get called in to handle tough problems that the initial Sprinkler

Back-Flow-Valve Service, Sprinkler Repair

Oklahoma Drainage and Sprinkler Repair Provides Service for Back-Flow-Valves and all types of Lawn Sprinkler Repair and Service.  We have provided Expert Service for all of Central and Western Oklahoma Since 1993.

Back-Flow-Valves

There are two types of Back-Flow-Valves.

Above Ground

 

Below Ground Back-Flow-Valve.

Below Ground Back-Flow-Valve

Below Ground Back-Flow-Valve

What is a Back-Flow-Valve?

A Back-Flow-Valve is a part of a Lawn Sprinkler System.  Water passes through it from the water source which can be a Water Meter or a Well Pump.  It forces water to travel in only one direction from the source to the sprinkler system.  It can’t travel backward back to the water source which again is a water meter or well pump.

A Back-Flow-Valve provides protection to the water source from back pressure and chemical contamination from lawn fertilizer.

Most Cities require a Back-Flow-Valve as “Code” for Sprinkler Installation.

Emergency Shut off

Back-Flow-Valves usually have an Emergency Shutoff valve on them that can shut off the water to the lawn sprinkler system but keep the water turned on to the home. Most Back-Flow-Valves have two Emergency Shut off Handles.  Either one will work.  Many times, they are hard to turn, however.

If there is a leak or water is shooting up in the air just turn the valve handle and give us a call.

In ground Back-Flow-Valve

Blue Emergency Shutoff handles for a Back-Flow-Valve.

Norman Sprinkler Checkup is a Central Focus for Oklahoma Drainage.  We Performed or first Sprinkler Repair in Norman in 1993.  It was in Brookhaven on the West side of Norman.

Recently we had a customer in Oklahoma City who wanted to move his Sprinkler Valves.  They were in a bad place in his flower bed.  He wanted to plant a tree where the valves were located.

We moved 4 Sprinkler Valves about feet out into the yard.  All the Sprinkler Pipes had to be redesigned and installed matching the new location and maintaining full functionality.

 

What Is a Sprinkler Valve?

Think of a Sprinkler Valve as an “Off or on” Switch.    The Sprinkler Controller   turns the valves on or off.

It Sends a signal through a wire which is underground to the sprinkler valve somewhere in your yard.

Once turned on, the valve lets water pass through a sprinkler pipe to a specific group of sprinkler heads called a Sprinkler Zone.  The controller allows water to reach the sprinkler heads for a certain amount of time running through the sprinkler valve.  Once the time is up, it shuts off the sprinkler valve and moves on to the next valve in sequence.

Think of it as walking into every room in your house one at a time.  As you enter you turn on the light.  As you leave you turn off the light and move to the next room. You are the controller.  The light switch represents the sprinkler valve.

Rainbird Sprinkler Valve

Rainbird Sprinkler Valve

The Sprinkler Valve in the picture above was taken out of the ground after the pipe froze and broke on the right side.  You can see the crack in the PVC pipe.  Of course, I had to clean all the mud off the valve before I took the picture.

What causes a Sprinkler Valve to stop working?

Like anything else, a sprinkler valve can wear out.   Sprinkler valves fail in closed position.  It won’t run continuously if it breaks.

Sprinkler Valves get stuck while running sometimes.   The water supply must be then turned off to stop the Sprinkler from running.

Sprinkler Valves can freeze and break in the winter if the sprinkler system has not been properly drained for winter’s cold.

(winterized)

Tree roots can twist or break sprinkler pipes running into sprinkler valves.  Magnolia Trees are really bad about this.  Oak trees can cause damage too.

Driving something heavy across your yard can crush sprinkler valves.  Usually riding lawnmowers don’t cause damage but any truck or car will if you drive over a valve.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

rotor sprinkler Head

Rotor Sprinkler Head

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provides Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

Emergency Sprinkler Repair

Sometimes things go wrong with sprinkler systems.

 

 GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR.  405 203 9419

One Common problem is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

Curb Outlet Installation, French Drain, Surface Drain, Sprinkler Repair Service.

Curb Outlet Installation. Oklahoma Drainage and Sprinkler Repair has installed Curb Outlets for French Drains and Surface Drains Since 1993.

If you want to tackle this yourself, the following Information will be helpful.

Curb Outlet installation is usually too much “Specialization,” for a “Week-End-Warrior” or your Brother-In-Law to do.

However!

Any Determined Person with Basic Skills can do it.

 

Before you ever build a Drainage System, you need to decide where you are going to take the problem water too.   Most residential Drainage Systems release water farther on down the hill or release it out into the street.  Street release is either over the curb or through the curb.

Curb outlet for French drain

Curb Outlet for French Drain

It is a good idea to do a little research on the effects and liabilities of releasing water at your home.  What does the city think if you release water through the curb vs over the curb?  What does your downhill neighbor think if you are releasing water into his yard?

Some Drainage System Locations have many options for ” Exits.”  Others have very few.

Don’t Start a Drainage System if you don’t have a good place for the water to exit!

This is even more important, if your Drainage System needs to be a “Flood Prevention System.”  We talked about this in the previous blogs on Drainage.

A Flood Prevention System may need more than one exit to increase the Drainage Systems Capacity.

OK, So you have a good Water Exit Strategy and have identified where the water is going to go.

Let’s go back and talk about Pop Up Emitters and Curb Outlets.

A Pop Up emitter is used to release water down a hill or over a curb and into the street.

Pop up emitter next to sidewalk

Popup Emitter to release water from a French Drain in Yukon

 

new curb outlet

Curb outlet with more than 6 inches of fall

 

Pop up emitter and ADS

Pop-Up Emitter before Installation

Water hits the Emitter and fills it until the water pressure lifts the lid and the water drains out.

Good “Fall” or ” Slope

is necessary for a pop up emitter to work properly.  Many times, a Drainage Pipe does not run downhill enough for a Drainage System to work well. You need “Slope” for your drain to work.   Water may move very slowly and never lift the lid and it just sits there.

We will talk about having the correct amount of “Fall” or “Slope” in a Drainage System in the next blog.

Curb fittings or outlets is the other way to release water.

 

cement curb outlet

Curb Outlet as an Exit Point for a French Drain in Edmond

First off,  For your average DIY Guy.  Installing a Curb outlet may be beyond your skill set or capacity.  If that is the case just place a Pop-Up Emitter up against the curb and go on about your business.

That being said, you may still want or need a Curb Outlet set in concrete.

If you are good with concrete and a concrete saw, this option poses no problem.  If this option seems too much for you, it probably is!  Consider sub-contracting the curb outlet.  In higher populated areas, finding someone to do “Light” concrete work is relatively easy.  You still can save money by installing the rest of the Drainage System yourself.

If you are still going to install the “Curb Outlet,” here are the steps for a “First Timer.”

Installing a Curb fitting Yourself Isn’t Easy

In 34 years of service, Oklahoma Drainage and Sprinkler Repair has installed over 2000 curb outlets.

If you are comfortable with your Skills using a Concrete Saw and working with a small amount of concrete, you can install your own curb fitting.

Step 1 Find a Curb outlet fitting.  They are round on one side where the drainpipe connects and rectangular on the other to fit in the cut-out area for the Curb outlet.

Curb outlet fitting

Curb outlet fitting

They are sold in many Drainage Supply Businesses.  You may not find them at “Lowes” or ” Home Depot”.  It varies.  If a Specialized Drain Supply business is not available then use a “Heat and Air” Floor vent as your curb outlet.  They are made of metal in most cases but still will work very well.  I have done this many times.  The floor vent is typically wider and thinner than a standard Curb Outlet Fitting.  Just cut a wider hole in the curb.

Step 2 Watch an instructional safety video on using a concrete saw.

Step 3 Rent or buy a concrete saw.  A used one can be found in pawn shops for about 300$ to 600$.  A New one will run around a Thousand Dollars.

a Rental will run about 50$ to 150$ depending on your area.

 

Find a Curb Outlet Fitting

Step 4 Find a Curb outlet that matches the size of your Pipe.  If you have a 4 inch Drain pipe then install a 4 inch curb outlet.   Sometimes a Six inch Curb outlet is too big to install in many roadside curbs.  It is too tall in many cases.  In most situations if you want a curb outlet and have a Six inch Drain Pipe, you must install two 4 inch outlets side by side.

If you have the need for a six inch Drainpipe, that means you have a lot of water to move.  You don’t want to create a bottle neck at the curb by installing a 4 inch curb fitting as your exit on a Six-Inch Drainpipe.

What you need to do is dig a large hole at the curb so you have room to work.  Next you attach a 6 inch “Y” fitting onto your drain pipe above the curb several feet.  You then install Two Reducer Bushings in both outlets of the “Y” fitting.  Next you attach 4 Inch ADS Drainpipe to the outlets and run two 4 inch ADS Drainpipes to the Curb.  Now you install two 4 inch curb fittings side by side.

It is very important

to use ADS Pipe coming out of the 6 Inch “Y” fitting.  It is Flexible and can be easily bent to fit your application.   PVC Pipe is rigid and won’t bend.  Very few people can do this process using PVC.  In 33 Years of installing Drains, I have only done it 3 times using PVC.  It is very Difficult and Frustrating.

Step 5 Watch a Video on Light Concrete Work if available.

Step 6 Connect the curb fitting to the drainpipe and install cement around it.  I have had the most success using a ” Quick Set” concrete that comes in a small bucket and has an “Acrylic” Additive or Base.

I don’t recommend cutting the curb yourself and installing a curb outlet if you are only going to do this once in your life.  If you are or will become a drainage contractor, then this is a skill that you definitely need.

 

 

Sprinkler System Checkup Edmond, Service, Repair

Lots of things can be done to make sure your Sprinkler System is ready to go.  All the Sprinkler Zones should be checked one by one.  The sprinkler heads and valves need to be checked to see if anything needs to be adjusted or replaced.

Sprinkler System Checkup is a Service Provided by Oklahoma Drainage since 1993.

Today we did a sprinkler repair in Norman.  The sprinkler system needed a checkup.

We went through each sprinkler zone and identified several different problems.

Zone 2 had a cracked sprinkler pipe in a flower bed.

A broken Rotor Sprinkler head was found immediately.

Next, zone five look good with no problems.

Zone 6 and 7 each had a couple of pop-up spray heads that were worn out and would not pop-up.  The diagnosis and the repair took less than two hours.  Now their sprinkler system is running great!

Now is a good time to have a Sprinkler System Checkup provided by Oklahoma Drainage.

Sprinkler Systems need to be checked before winter to prevent pipes from freezing.  Sprinkler Design determines whether sprinkler lines need to be bled.  Emergency shut off valves also need to be checked and turned off for the winter.

In the Spring, all the water needs to be turned back on and all sprinkler zones and heads need to be tested.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provide Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

Sprinkler Valves

Sprinkler Valve Replacement is a service that Oklahoma Drainage has provided Since 1993.  Recently we removed 3 Rainbird Sprinkler Valves and replaced them with new ones.  The valves had been crushed accidentally when a landscaper drove his truck across the yard.

Sprinkler System Check-Up in Edmond, Oklahoma City, Norman, and Moore.

 

 

Sprinkler System Check-Up process is very straightforward.  We run through all the Sprinkler Zones one-at-a- time from the controller. 

Sprinkler Controller

Sprinkler controllers can be a problem source.   Many times, the wires in the controller are loose or have a “Short” in one of the wires.  Sprinkler Programming can be a source of frustration.  We can help with Programming your controller.

We check all the sprinkler heads in that zone and the valves as well.

Once the Sprinkler System Checkup is Complete, we provide a Quote for what it will cost to make the needed repairs.

Oklahoma Drainage and Sprinkler Repair — Installing – French DrainsSurface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler RepairBroken Sprinkler Pipes Sprinkler Head AdjustmentSprinkler Valve Replacement

Servicing all of Central and Western Oklahoma since 1993.  405 203 9419

Sprinkler Valve Replacement is a service that Oklahoma Drainage has provided Since 1993.  Recently we removed 3

 

Sprinkler Leaks Edmond.

Oklahoma Drainage and Sprinkler Repair has fixed Sprinkler Leaks in Edmond since 1993.  405 203 9419

Sprinkler Repair is also very popular this time of year.  Folks in Central Oklahoma are turning on their Sprinkler Systems and discovering problems.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR, Provides Expert Sprinkler Repair for:  Sprinkler Valves, Sprinkler Heads, Sprinkler Controllers, and the most common problem, Sprinkler Pipes or Sprinkler Leaks.

Sprinkler Repair Service is provided for: Oklahoma City, Norman, Edmond, Yukon, Mustang, Moore, Midwest City, Blanchard, New Castle, and all surrounding areas.

No PVC Primer Used.  Yikes!!!

We fixed several leaks in a Sprinkler System in Edmond.  The sprinkler pipes were leaking in several places.  Each leak had to be cut out and replaced.

The Sprinkler System was fairly new.  It was installed last summer by a Pool Company that also installs cheap sprinkler systems.

All the joints in the sprinkler pipes were glued together with clear PVC Cement.  That part is OK, but they cut some corners and didn’t use PVC Primer with the glue.  As a result, the joints didn’t bond very well and many of them blew apart this spring when the sprinkler systems were turned on.  (Thus, all the leaks)

I suspect we will have to go back several times to fix additional leaks.  We can only warranty the PVC joints that we have replaced.   Cheaper isn’t always better.

 

Sprinkler pipes may leak for many reasons.  Pipes that are too shallow can freeze and break during the cold of winter.  Repair of PVC Sprinkler pipe in cold temperatures can be difficult.  Frozen Ground is difficult to dig up to get to the damaged pipe.  PVC Glue and Primer don’t bond very well in temperatures that are low.  Even using “Hot Glue,” which is designed to be used in cold temperatures doesn’t always produce the best results.

Oklahoma Drainage and Sprinkler Repair can provide the necessary expertise to handle difficult sprinkler repairs.

Oklahoma Drainage and Sprinkler Repair provides Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

One Common Problem

One Common problem is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

 

Inside the valve box is a plastic handle that can turn off the water to the sprinkler system.  It can be blue or red or grey in color.

Many times, the valve box will be full of dirt, and you can’t turn or even see the handle until some of the dirt has been dug out by hand.

 

Water might be shooting up in the air somewhere on your property.  This can be caused by a broken sprinkler pipe or sprinkler valve.

SHUT OFF THE SPRINKLER WATER IF YOU CAN AND GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR. SERVICING ALL OF CENTRAL AND WESTERN OKLAHOMA.

405 203 9419

Servicing Oklahoma City, Norman, Edmond and all of Central and Western Oklahoma

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Sprinkler Controller

Sprinkler Controller

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,     Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

We started with the Valves

The Sprinkler Valves were located in the back yard near the pool.  Six valves were located in one place.  They were very tightly connected in one Manifold.  None of the Sprinkler Valves had worked in a long time.  They were Toro Valves that were over 20 years old.  They all had to be replaced.

Surprisingly there was no shut-off valve for the Sprinkler Water.  The water had to be shut off at the Meter so we could install a Manual Shut off valve.  Once installed, the water was turned back on that ran to the house.   The water that ran to the Sprinkler System was shut off with our New Shut Off Valve.

The Sprinkler Valves Were Removed

Now, the 6 valves had to replaced.  The valves that were used were made by Rain Bird.  Before we began, I had to talk to the Customer.  The previous valve design was a bad idea to repeat.

The original Sprinkler Valves were crammed into one large valve box in one very tight manifold.  This is bad because the valves were too close to the fittings.  Simply put, if one valve had to be replaced or worked on in the future, all 6 valves had to be taken out and replaced.   If one valve was bad and 5 worked fine, they all still had to be replaced.

That’s Stupid!

I recommended that an additional Valve Box be installed putting 3 valves in each Valve Box.  This would allow plenty of space between the valve fittings.  If one Sprinkler Valve had to be adjusted or replaced in the future, the other 5 valves need not be disturbed.  Simple Enough!

Check For Leaks

Once the valves were replaced and working, it was time to turn on each Sprinkler Zone, one at a time.  Water was shooting up from the ground in several places in zone 1.  Two broken Sprinkler Pipes and 5 bad Sprinkler Heads in zone 1 had to be fixed and replaced.  We went through each of the 6 zones in similar fashion fixing lots of leaks and replacing bad sprinkler heads.

The Sprinkler Repair Cost About Half of the Cost of Completely New System.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

Sprinkler Head Adjustment is a service provided by Oklahoma Drainage and Sprinkler Repair.  We have adjusted sprinkler heads since 1993.

Many times, Sprinkler heads get, “Out of Wack.”  Lawn mowers and weed eaters are notorious for this.  Sprinkler heads start spraying water in the wrong place.  It is frustrating to water concrete while plants and grass go without moisture.

Pop-Up Sprinkler Heads

Pop-Up Sprinkler Heads can be adjusted several ways.  How far water goes to the left or right can be increased or decreased.  The distance the water goes can also be increased or decreased.  Finally, how high a sprinkler head pops up can be increased or decreased by installing a taller or shorter head.

Sometimes sprinkler heads spray a reduced distance and don’t perform very well due to water scale.  Minerals in the water can completely clog a Pop-Up.  Usually, the sprinkler nozzle on top of the sprinkler head, need only be replaced without replacing the entire head.

Rotor Sprinkler Heads also can be adjusted to the left or right.  Spray Distance can be increased or decreased as well.

Needs Change

What’s going on in your yard can change.  This calls for Sprinkler Head Adjustment.  Adding or removing a swimming pool changes everything concerning sprinkler heads.  Any number of things can change the necessary sprinkler head coverage.

 

 

Oklahoma Drainage and Sprinkler Repair — Installing – French DrainsSurface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler RepairBroken Sprinkler Pipes Sprinkler Head AdjustmentSprinkler Valve Replacement

We provide Service for Folks in: Norman, Oklahoma City, Edmond, and Moore.

Central and Western Oklahoma is our Service Area since 1993.  

                                                           (405) 203-9419

Check out Sprinkler System Check-Up

Sprinkler Repair is also very popular this time of year.  Folks in Central Oklahoma are turning on their Sprinkler Systems and discovering problems.

We fixed several leaks in a Sprinkler System in Edmond.  The sprinkler pipes were leaking in several places.  Each leak had to be cut out and replaced.

The Sprinkler System was fairly new.  It was installed last summer by a Pool Company that also installs cheap sprinkler systems.

All the joints in the sprinkler pipes were glued together with clear PVC Cement.  That part is OK, but they cut some corners and didn’t use PVC Primer with the glue.  As a result, the joints didn’t bond very well and many of them blew apart this spring when the sprinkler systems were turned on.  (Thus, all the leaks)

I suspect we will have to go back several times to fix additional leaks.  We can only warranty the PVC joints that we have replaced.   Cheaper isn’t always better.