Posts Tagged ‘Moore French Drain’

Lawn Sprinkler Repair Moore Oklahoma, French Drain

Posted: February 8, 2026 in french drain, sprinkler repair, Sprinkler Repair Service, Sprinkler Service
Tags: , , ,
0

Lawn Sprinkler Repair Moore Oklahoma.  Oklahoma Drainage and Sprinkler Repair– 405 203 9419

Lots of things can be done to make sure your Sprinkler System is ready to go.  All the Sprinkler Zones should be checked one by one.  The sprinkler heads and valves need to be checked to see if anything needs to be adjusted or replaced.

Sprinkler System Checkup is a Service Provided by Oklahoma Drainage since 1993.

Today we did a sprinkler repair in Norman.  The sprinkler system needed a checkup.

We went through each sprinkler zone and identified several different problems.

Zone 2 had a cracked sprinkler pipe in a flower bed.

A broken Rotor Sprinkler head was found immediately.

Next, zone five look good with no problems.

Zone 6 and 7 each had a couple of pop-up spray heads that were worn out and would not pop-up.  The diagnosis and the repair took less than two hours.  Now their sprinkler system is running great!

Now is a good time to have a Sprinkler System Checkup provided by Oklahoma Drainage.

Sprinkler Systems need to be checked before winter to prevent pipes from freezing.  Sprinkler Design determines whether sprinkler lines need to be bled.  Emergency shut off valves also need to be checked and turned off for the winter.

In the Spring, all the water needs to be turned back on and all sprinkler zones and heads need to be tested.

Spraying Rotor Sprinkler Repair

Spraying Rotor Sprinkler Head

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provide Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

Sprinkler Valves

Sprinkler Valve Replacement is a service that Oklahoma Drainage has provided Since 1993.  Recently we removed 3 Rainbird Sprinkler Valves and replaced them with new ones.  The valves had been crushed accidentally when a landscaper drove his truck across the yard.

Sprinkler System Check-Up in Edmond, Oklahoma City, Norman, and Moore.

 

 

Sprinkler System Check-Up process is very straightforward.  We run through all the Sprinkler Zones one-at-a- time from the controller. 

Sprinkler Controller

Sprinkler controllers can be a problem source.   Many times, the wires in the controller are loose or have a “Short” in one of the wires.  Sprinkler Programming can be a source of frustration.  We can help with Programming your controller.

We check all the sprinkler heads in that zone and the valves as well.

Once the Sprinkler System Checkup is Complete, we provide a Quote for what it will cost to make the needed repairs.

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes – Sprinkler Head Adjustment – Sprinkler Valve Replacement

Servicing all of Central and Western Oklahoma since 1993.  405 203 9419

Sprinkler Valve Replacement is a service that Oklahoma Drainage has provided Since 1993.  Recently we removed 3 Rainbird Sprinkler Valves and replaced them with new ones.  The valves had been crushed accidentally when a landscaper drove his truck across the yard.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provide Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

First Step

First, we dug up a good working area surrounding the broken Sprinkler Valves.  Next, we cut out the broken valves and crushed PVC pipes.  Finally, PVC pipe was cut and glued with new Sprinkler Valves following the original design and configuration.  In this case the three original sprinkler valves were connected to each other inside one Valve Box.

We aren’t done yet though; two sprinkler wires must be connected to each Valve.  One sprinkler wire is the “Common Ground.”  The other wire is the power wire.  All the sprinkler wiring is connected with water-proof wire connections.

The Common Ground wire and the Individual Power Wires all come from the Sprinkler Controller.  Each Sprinkler Valve has its own power wire coming from the Controller.  All the Sprinkler Valves are Connected to the Same Common Ground Wire.

Sprinkler Valve Replacement

Oklahoma City Sprinkler Repair

Before We Finish

Before dirt can be put back around the new valves, testing must be done.  Each valve must be turned on, “one-at-a-time,” at the Controller to ensure good wire connection and functionality.  Also, the Sprinkler Valves must be checked for leaks in the PVC Pipe.

Oklahoma Drainage and Sprinkler Repair provides Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

Blanchard Sprinkler Repair has been provided by Oklahoma Drainage and Sprinkler Repair since 1993.

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

A Sprinkler Controller can be a big “Headache,” for a Homeowner.

Sprinkler Controller

Oklahoma Drainage – We install French Drains, Channel Drains, Surface Drains, Sump Pumps and Sod.

If You live in Oklahoma City and water damaging your foundation, we can install a French Drain for you.

Or,If you live in Norman and have water standing on your driveway, consider a Channel Drain Installation.

If you live in Edmond and have water flooding your basement, a Sump Pump can help.

Or, you live in Moore and have water washing out your flower bed mulch, We can install a Surface Drain for you.

If you live in Yukon and need grass to grow, we can install Sod too!

Installing Drain Pipe from French Drain in Back Yard

Installing Drainpipe from French Drain in Back Yard

Do you have water standing in your yard after a heavy rain?  Do your gutters turn your sidewalk into a moat after a storm.  Worst of all, do you have water seeping into your home or business from Storm-Water runoff?

 

Installing Solid 4 Inch Drain Pipe Between French Drain and Curb

Installing Solid 4 Inch Drainpipe Between French Drain and Curb

Oklahoma Drainage can help with these and many other “standing water” and ” Drainage Problems. We can diagnose your drainage problem and design a drainage system to fit your specific needs.  In Business since 1993.  

We utilize: French Drains, Surface Drains, Channel Drains, Basin Drains, Trench Drains, Basement Drains, and Sump Pumps.

 

We service all of Central and Western Oklahoma

 

Oklahoma Drainage and Sprinkler Repair provide Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

Sometimes things go wrong with sprinkler systems.

 

Grass Growing Over French Drain, Norman Sprinkler Repair

Posted: January 12, 2026 in french drain, French Drain Repair, French Drain Service, sprinkler repair, Sprinkler Repair, Sprinkler Service
Tags: , , , ,
1

Grass Growing Over a French Drain can be a good thing.  Let Oklahoma Drainage and Sprinkler Repair tell you why!

French Drain Installation in sun or shade.  Oklahoma Drainage and Sprinkler Repair can show you the difference.

Oklahoma Drainage– We install French Drains, Channel Drains, Surface Drains, Sump Pumps and Sod.

If You live in Oklahoma City and water damaging your foundation, we can install a French Drain for you.

 Or If you live in Norman and have water standing on your driveway, we can install a Channel Drain for you.

If you live in Edmond and have water flooding your basement, we can install a Sump Pump for you.

 Or If you live in Moore and have water washing out your flower bed mulch, we can install a Surface Drain for you.

If you live in Yukon and need grass to grow, we can install Sod too!

Servicing All of Central and Western Oklahoma Since 1993.

 

FRENCH DRAIN INSTALLATION IN SUN OR SHADE?

French Drain Running Through Low Areas

Rest Home French Drain Running Through Low Areas

 

French Drains are designed to cover large areas and move lots of water.  During a hard rain, water will seep down through the gravel and into the Perforated French Drainpipe that is buried under the gravel.  The water fills into the pipe and moves downhill to the desired Exit Point.  French Drains like the one in the picture above that are in the sun most of the day will have grass that overgrows the limestone.  The gravel will disappear over time.

Grass will Grow Over the Gravel

The French Drain will continue to work even after the grass has grown over it.  A “Thatch Filter ” is made up of the grass that covers the French Drain.  The French Drain then has two filters.

First is the Neo-Prene Soc that comes around the Perforated French Drainpipe.  Later when the grass grows over it, the French Drain then has a second Thatch Filter.  This ensures that the French Drainpipe won’t clog over time with dirt, sand, or debris.  This only works with grass that does well in the sun like Bermuda or Tift.

Shade Grasses won’t grow up and through French Drain gravel.

YOU DON’T WANT TO COVER THE FRENCH DRAIN WITH DIRT.  IT WILL GREATLY REDUCE THE DRAINAGE PERFORMANCE OF THE FRENCH DRAIN.  IT DEFEATS THE ENTIRE REASON FOR THE FRENCH DRAIN.  IF YOU DON’T LIKE THE WAY IT LOOKS AND CAN’T BE PATIENT ENOUGH TO WAIT UNTIL THE GRASS GROWS THROUGH IT IF IT IS IN THE SUN, THEN DON’T INSTALL IT AT ALL.

IF THE FRENCH DRAIN IS INSTALLED IN THE SHADE, YOU CAN USE DECORATIVE ROCK TO MAKE A FOOT PATH OR ROCK GARDEN ON TOP OF IT.  YOU ARE ONLY LIMITED BY YOUR IMAGINATION.

 

Lawn Sprinklers can have pipes that leak.   PVC Pipe is the most common Sprinkler System Pipe and leaks definitely are possible.

Leaking Sprinkler Pipes

Leaks can occur near Sprinkler Valves.  Water travels through Sprinkler Valves and can leak going in or coming out.

Many Cities require a back-flow valve to protect the City’s water supply.  It can also leak as water passes through the valve.

Leaks can also occur due to tree roots stressing Sprinkler Pipes.  The pipes can be twisted by roots and crack or break.

Water inside Sprinkler Pipes can freeze and break or crack the PVC Pipe.

Move sprinkler heads, Norman, Oklahoma City, Edmond

There are many reasons for moving Sprinkler Heads.

If you put in a new pool, most of the sprinkler heads will need to be moved.

Sprinkler Heads need to be moved if you have new landscaping installed.

Sometimes Sprinkler Heads weren’t in a good place to begin with.  They need to be moved!

Oklahoma Drainage and Sprinkler Repair can help.  We have been moving Sprinkler Heads since 1993.

In 32 years, we have moved a lot of Heads for Customers in Central and Western Oklahoma.

 

Oklahoma Drainage and Sprinkler Repair provide Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

Sprinkler Head Installation

Moving Sprinkler Head

Spraying Rotor Sprinkler Repair

Spraying Rotor Sprinkler Head

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,   Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

We started with the Valves

The Sprinkler Valves were located in the back yard near the pool.  Six valves were located in one place.  They were very tightly connected in one Manifold.  None of the Sprinkler Valves had worked in a long time.  They were Toro Valves that were over 20 years old.  They all had to be replaced.

Surprisingly there was no shut-off valve for the Sprinkler Water.  The water had to be shut off at the Meter so we could install a Manual Shut off valve.  Once installed, the water was turned back on that ran to the house.   The water that ran to the Sprinkler System was shut off with our New Shut Off Valve.

Rainbird Sprinkler Valve

Rainbird Sprinkler Valve

The Sprinkler Valves Were Removed

Now, the 6 valves had to replaced.  The valves that were used were made by Rain Bird.  Before we began, I had to talk to the Customer.  The previous valve design was a bad idea to repeat.

The original Sprinkler Valves were crammed into one large valve box in one very tight manifold.  This is bad because the valves were too close to the fittings.  Simply put, if one valve had to be replaced or worked on in the future, all 6 valves had to be taken out and replaced.   If one valve was bad and 5 worked fine, they all still had to be replaced.

That’s Stupid!

I recommended that an additional Valve Box be installed putting 3 valves in each Valve Box.  This would allow plenty of space between the valve fittings.  If one Sprinkler Valve had to be adjusted or replaced in the future, the other 5 valves need not be disturbed.  Simple Enough!

Check For Leaks

Once the valves were replaced and working, it was time to turn on each Sprinkler Zone, one at a time.  Water was shooting up from the ground in several places in zone 1.  Two broken Sprinkler Pipes and 5 bad Sprinkler Heads in zone 1 had to be fixed and replaced.  We went through each of the 6 zones in similar fashion fixing lots of leaks and replacing bad sprinkler heads.

The Sprinkler Repair Cost About Half of the Cost of Completely New System.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

Sprinkler Head Adjustment is a service provided by Oklahoma Drainage and Sprinkler Repair.  We have adjusted sprinkler heads since 1993.

Many times, Sprinkler heads get, “Out of Wack.”  Lawn mowers and weed eaters are notorious for this.  Sprinkler heads start spraying water in the wrong place.  It is frustrating to water concrete while plants and grass go without moisture.

Pop-Up Sprinkler Heads

Pop-Up Sprinkler Heads can be adjusted several ways.  How far water goes to the left or right can be increased or decreased.  The distance the water goes can also be increased or decreased.  Finally, how high a sprinkler head pops up can be increased or decreased by installing a taller or shorter head.

Sometimes sprinkler heads spray a reduced distance and don’t perform very well due to water scale.  Minerals in the water can completely clog a Pop-Up.  Usually, the sprinkler nozzle on top of the sprinkler head, need only be replaced without replacing the entire head.

Rotor Sprinkler Heads also can be adjusted to the left or right.  Spray Distance can be increased or decreased as well.

Needs Change

What’s going on in your yard can change.  This calls for Sprinkler Head Adjustment.  Adding or removing a swimming pool changes everything concerning sprinkler heads.  Any number of things can change the necessary sprinkler head coverage.

 

 

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes – Sprinkler Head Adjustment – Sprinkler Valve Replacement

We provide Service for Folks in: Norman, Oklahoma City, Edmond, and Moore.

Central and Western Oklahoma is our Service Area since 1993.  

                                                           (405) 203-9419

Check out Sprinkler System Check-Up

 

 

IF YOU NEED HELP IN THE MIDDLE OF THE NIGHT OR ON A WEEKEND WITH YOUR SPRINKLER SYSTEM, GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR.  405 203 9419

IT MAY TAKE A FEW HOURS FOR US TO GET THERE BUT WE WILL COME TO HELP.

 

One Common problem is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

 

Inside the valve box is a plastic handle that can turn off the water to the sprinkler system.  It can be blue or red or grey in color.

Many times, the valve box will be full of dirt, and you can’t turn or even see the handle until some of the dirt has been dug out by hand.

 

Water might be shooting up in the air somewhere on your property.  This can be caused by a broken sprinkler pipe or sprinkler valve.

SHUT OFF THE SPRINKLER WATER IF YOU CAN AND GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR. SERVICING ALL OF CENTRAL AND WESTERN OKLAHOMA.

405 203 9419

Servicing Oklahoma City, Norman, Edmond and all of Central and Western Oklahoma

 

 

Oklahoma City French Drains, Sprinkler Repair

Posted: September 30, 2024 in Emergency Sprinkler Repair, french drain, French Drain Information, French Drain Photos, Oklahoma City French Drain, Oklahoma City French Drains, Sprinkler Repair, sprinkler repair
Tags: , , , ,
67

Oklahoma City French Drain Installation Since 1993.

 

 

French Drain, Moore Oklahoma, Oklahoma City, Norman, Edmond, French Drain Repair

Oklahoma Drainage 405 203 9419

Check Out – Where We Have Worked

French Drain Installation

French drain Installation
with trench liner and pipe filter

Oklahoma City French Drain Installation has been a Central focus for Oklahoma Drainage since 1993.  We have served over 2000 customers.

We have installed a lot of French Drains in apartment complexes and businesses.  The majority of our business is with Homeowners.

Tell Your Friends about us!  Or just enter “OKLAHOMA CITY FRENCH DRAIN INSTALLATION,” into Google.

What is a French Drain?

Click the Link Above

1993 was a long time ago.  Oklahoma Drainage has installed French Drains, Surface Drains, Channel Drains and Sump Pumps for over 30 years.  We also provide Sprinkler Repair.  

Duck enjoying a French Drain

I should hire these guys to test French drains.

Check Out Our Drain Photo Library

Oklahoma Drainage provides top quality Sprinkler Repair Service.  If you live in Oklahoma City and need a Sprinkler Head moved, we can help.  You might have a Sprinkler Pipe leak that needs attention.  A Sprinkler Valve might we wore out as well.  You might just want a Sprinkler System Checkup for Spring.  For these problems and many others, Oklahoma Drainage can help.

We service Oklahoma City, Norman, Edmond and all of Central and Western Oklahoma.

Emergency Sprinkler Repair

Sometimes things go wrong with sprinkler systems.

 

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR.  405 203 9419

 

One Common problem is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

Above Ground Back-Flow-Valve

Above Ground Back-Flow-Valve.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

 

Inside the valve box is a plastic handle that can turn off the water to the sprinkler system.  It can be blue or red or grey in color.

Many times, the valve box will be full of dirt, and you can’t turn or even see the handle until some of the dirt has been dug out by hand.

 

Water might be shooting up in the air somewhere on your property.  This can be caused by a broken sprinkler pipe or sprinkler valve.

SHUT OFF THE SPRINKLER WATER IF YOU CAN AND GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR. SERVICING ALL OF CENTRAL AND WESTERN OKLAHOMA.

405 203 9419

Servicing Oklahoma City, Norman, Edmond and all of Central and Western Oklahoma

 

Installing 4 Inch French Drain with trench Liner and pipe filter

The White Material is the Trench Liner. The black material is the Pipe Filter.

We Install Drainage Systems to fit various needs for homeowners an businesses.  A Drainage System can utilize French Drains, Surface Drains, Channel Drains or Sump Pumps as the intake part to the Drainage System. 

The Drain or Sump Pump brings water into the Drainpipe.  The Drainpipe takes the water to the ” Exit.”  Which is Either a “Curb Outlet” or a “ Pop Up Emitter.”

The Three parts of A Drainage System are:   THE INTAKE (French Drain or Surface Drain ) etc.  The TRANSITION (The Pipe) which can be many sizes or type. The EXIT ( A Curb Outlet or Pop Up Emitter )

 

 

new curb outlet

Curb outlet with more than 6 inches of fall

 

Need for a Drainage System

The Drainage part of our company name means that we solve water problems for people in Oklahoma.  Heavy rain is becoming more common.  Back in 1993 when I first started, a hard rain was considered to be about an Inch per/hour.  It was fairly rare but not too uncommon.  Today things are different.  A weather report of rain falls at or above 4 inches per/hour was not uncommon in 2019.  Excess water causes all types of damage to property both residential and commercial.

Our Drainage Systems drain water away from places you don’t want it to be.  You might have water standing along the foundation of your house, or inside your basement.  You might have water on your driveway or flowerbed too.

Designing a French Drain or a Drainage System

When I talk to a potential customer while doing a Drainage System estimate, I take a lot of things into consideration.  First, I have the Customer show me where water is standing or where it is going that it shouldn’t.  This is part of defining the specific problem area.

Sometimes the Water Problem Area is larger and more involved than the customer realizes.  Once the Water Problem Area is clearly defined, the next step is to determine how the water is getting to the problem area.  Many times, there is more than one Water Source to the Water Problem area.  A big mistake in Drainage System Design is to stop once the most obvious Water Source is found.

A Drainage System Designer must be a detective to some degree.  For Example:  Water running down the hill and onto the back patio might be the most obvious water source.  Sub-surface water or a neighbor’s new gutter downspout could also be contributing.  Most of the time water gets into the problem area from more than one source.

Next you must decide where to take the water.  This is determining an Exit Point for the Drainage System.  If possible, you want your exit point to be downhill from the problem area.  If it is up hill in all directions from the problem area, then the only solution is a Sump Pump.

Once an exit Point is determined,

you must ask yourself if there is any way to install two exit points.  Usually this can only work when an exit point can work on both ends of a Drainage System.  The benefit of two Exit Points in a Drainage System is it greatly increases the water capacity.  It can move much more water faster during a heavy rain than a system with just one Exit Point.  Most Drainage Systems can only utilize one Exit Point.  With 30 years of Drainage Installation, I would say 10% of our Drainage Systems have two Exit Points.

Popup Emitter to release water from a French Drain in Yukon

Popup Emitter to release water from a French Drain in Yukon

Next we have to decide what type of drain to install in the problem area.  If it is a small area with one water source, or lots of sources.

Oh! we also solve water problems and provide Drainage.

Oklahoma Drainage – We install French Drains, Channel Drains, Surface Drains, Sump Pumps and Sod.

If You live in Oklahoma City and water damaging your foundation, We can install a French Drain for you.

Or,If you live in Norman and have water standing on your driveway, consider a Channel Drain Installation.

If you live in Edmond and have water flooding your basement, a Sump Pump can help.

Or, you live in Moore and have water washing out your flower bed mulch, We can install a Surface Drain for you.

If you live in Yukon and need grass to grow, we can install Sod too!

Installing Drain Pipe from French Drain in Back Yard

Installing Drainpipe from French Drain in Back Yard

Do you have water standing in your yard after a heavy rain? 

Do your gutters turn your sidewalk into a moat after a storm.  Worst of all, do you have water seeping into your home or business from Storm-Water runoff?

 

Installing Solid 4 Inch Drain Pipe Between French Drain and Curb

Installing Solid 4 Inch Drainpipe Between French Drain and Curb

Oklahoma Drainage can help with these and many other “standing water” and ” Drainage Problems. We can diagnose your drainage problem and design a drainage system to fit your specific needs.  In Business since 1993.  

We utilize: French Drains, Surface Drains, Channel Drains, Basin Drains, Trench Drains, Basement Drains, and Sump Pumps.

 

We service all of Central and Western Oklahoma

 

 

French Drain Mistakes and Considerations, Sprinkler Repair

Posted: September 27, 2024 in Emergency Sprinkler Repair, french drain, French Drain Help, French Drain Information, French Drain mistakes, French Drain Problems, sprinkler repair
Tags: , , , ,
2

French Drain Mistakes

French Drain mistakes are made by Homeowners and Contractors.  We will focus on mistakes made by Homeowners.

 

Oklahoma Drainage installs French Drains, Channel Drains, Surface Drains and Sump Pumps.  We also provide top quality Sprinkler Repair for all of Central and Western Oklahoma.

 

Trench Liner and Pipe Filter Installed on French Drain

Trench Liner and Pipe Filter Installed with French Drain

French Drain Mistakes are very common and unfortunate.   Mistakes are caused by many different reasons.  One or several mistakes can cause a New French Drain to perform poorly, or not at all.  Time and money are wasted.  People with Water Damage need to have their drainage system work correctly and last a long time.

People who have need for French Drain Installation are highly motivated.  Unwanted water in your AC Floor Ducts for example, motivates folks to do something quickly.

Cracking Driveways

Cracking Driveways and Foundations from Water Damage is also an “ATTENTION GETTER.”

In the picture below, look at the water stains on the Driveway.  A correctly installed 6 Inch French Drain has solved the Standing Water Problem.  The driveway will stay dry and last.

French Drain Versatility is a wonderful thing.   Correct French Drain Installation solves a wide variety of water drainage problems.

Still Mistakes Are Made.

To Start, The Biggest French Drain Mistake is a Unqualified Drainage Diagnosis.   This is taking bad advice from someone who really doesn’t know.   Bad advice leads to a Drainage System that performs poorly or won’t work at all. This Obviously, occurs all the time in today’s world, whether It be French Drain Diagnosis or Auto Repair, or any other contract work you might want done.

Typical Mistakes

Additional mistakes that relate to Unqualified Drainage Diagnosis are:

1.  Selecting a Drainage Contractor that can’t provide good current References.

2.  Selecting a Drainage Contractor that has been in business less than 5 years.

3.  Selecting a Drainage Contractor that doesn’t specialize in French Drain Installation.

4.  Selecting a Drainage Contractor Who needs money up front.

In Review, If you have a French Drain Contractor who needs money up front to begin work, or is also good at landscaping or pushing a lawn mower, then you should RUN!  You need References! You need to know how long they have been in business.

Drainage System VS Flood Prevention System

The Second Most Common French Drain Mistake Is NOT DECIDING if a French Drain should be a part of a “Drainage System,” or a “Flood Prevention System.  You need to understand the difference between the two and choose one.  A French Drain Expert can help you make that decision.   A French Drain can be a part of A Drainage System or a part of a Flood Prevention System.

A Drainage System drains water away from a Water Problem Area over time.

A Flood Prevention System prevents water from ever getting into the Problem Drainage Area in the first place.

Flood Prevention Systems Intercept Surface Water and Sub-Surface water at the same time.  The pipes are larger and more robust than the pipes in a Drainage System.  Flood Prevention Systems are more expensive and harder to install as well.

The Third mistake that is made with a French Drain being installed is lack of a Trench Liner or Pipe Filter being used.  The Trench Liner maintains the integrity of the Drainage Trench and keeps the Gravel or Crushed Stone that is used clean.

The Pipe Filter keeps Debris out of the French Drain Pipe.

Both of these things ensure longevity and functionality of a French Drain.  I have Installed French Drains all the way back to 1993 that still work great!

The 4th mistake with a French Drain Installation is ,” Not Setting The Fall of the French Drain.”  “Setting The Fall,” is a process that makes sure that water flows through the French Drain Trench at a Constant Speed.  French Drains always cross ground that is irregular.  They cross humps and low areas.  This process is done by French Drain Professionals or Individuals who are accomplished and understand the two ways that “Fall may be set.”

Bad Fall

“Bad Fall,” For a French Drain means that water will stand in several low areas of the French Drain underground.    Once the French Drain has finished draining, it should be empty.   You want all the water to drain out of the French Drain Pipe.  By looking at the French Drain on the surface, It will look fine.    You won’t be able to tell if some of the Drainage Water Stayed inside the French Drain.  Everything will look OK, but it won’t be.  If any type of tree is nearby, the tree roots will seek out the water that is left in a french drain.   Tree roots attack the French Drainpipe causing damage.  Soon  French Drain Performance will drop off.  In may quit working completely over time.

TREE ROOTS WON’T ATTACK A FRENCH DRAINPIPE THAT IS EMPTY!

Oklahoma Drainage provides top quality Sprinkler Repair Service.  If you live in Oklahoma City and need a Sprinkler Head moved, we can help.  You might have a Sprinkler Pipe leak that needs attention.  A Sprinkler Valve might we wore out as well.  You might just want a Sprinkler System Checkup for Spring.  For these problems and many others, Oklahoma Drainage can help.

We service Oklahoma City, Norman, Edmond and all of Central and Western Oklahoma.

Emergency Sprinkler Repair

Sometimes things go wrong with sprinkler systems.

 

IF YOU NEED HELP IN THE MIDDLE OF THE NIGHT OR ON A WEEKEND WITH YOUR SPRINKLER SYSTEM, GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR.  405 203 9419

IT MAY TAKE A FEW HOURS FOR US TO GET THERE BUT WE WILL COME TO HELP.

 

One Common problem is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

 

Inside the valve box is a plastic handle that can turn off the water to the sprinkler system.  It can be blue or red or grey in color.

Many times, the valve box will be full of dirt, and you can’t turn or even see the handle until some of the dirt has been dug out by hand.

 

Water might be shooting up in the air somewhere on your property.  This can be caused by a broken sprinkler pipe or sprinkler valve.

SHUT OFF THE SPRINKLER WATER IF YOU CAN AND GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR. SERVICING ALL OF CENTRAL AND WESTERN OKLAHOMA.

405 203 9419

Servicing Oklahoma City, Norman, Edmond and all of Central and Western Oklahoma

 

 

 

 

 

French Drain Blanchard, Installation, Information, Sprinkler Repair,Norman, Moore, Edmond,

Posted: April 9, 2023 in Blanchard French Drain, french drain, French Drain Help, French Drain Information, French Drain Installation
Tags: , , ,
0

French Drain Blanchard, Installation, Information, Norman, Moore, Edmond, Blanchard

Servicing Central and Western Oklahoma Since 1993

Oklahoma Drainage recently diagnosed a Drainage Problem in South Oklahoma City.  The Home owner had a sump Pump in their basement that was fed from a French Drain outside the Basement Wall.  The Drain was 14 feet down along the Stem wall of the house.

The French Drain Pipe was cheap and had collapsed.  We brought in a Mini Excavator and dug up the pipe and replaced it with Durable ADS 4 inch perf/soc French Drain pipe.  In the end, we were able to dig up the pipe and replace it.

French Drain Design

French Drain Design must take into account many variables.  One consideration for a French Drain that many times is missed, is the type of soil.  French Drain Design must take into account the type of soil that the French Drain runs through.  If the soil is “Tight or made up of Clay, A French Drain Liner may not be necessary.  The Gravel or Limestone that is used to fill the French Drain trench may be all that is needed to maintain the integrity of the trench over time.   This means that dirt will not mix in with the French Drain Gravel and clog it up over time.

This is not the case however if your soil is sandy or loose.  A Trench Liner should be used to prevent this type of soil from moving into the gravel of the French Drain.  Trench Liners are relatively inexpensive and are not hard to install.  If you are not sure what to do then install the Trench Liner in the French Drain.

What Does a  Good Drainage System Have?

A good Drainage System has a point where water enters the System.  This is usually through a French Drain, Surface Drain, or a Gutter Down Spout that is connected into a Drainpipe.

Water will run through either Perforated French Drainpipe or Solid Drainpipe depending on the Drainage System Design.  Water will flow down hill to an Exit Point where the water will be released out of the Drainage System.  This is a done through a Pop-Up Emitter or a Curb Fitting.

Drainage Systems can be made up of one drain or a combination of many drains.  They can be very complex.   Complex Drainage Problems may require a combination of several different types of drains all inter-connected and working together.

Other times the drainage problem may be simple and straight-forward requiring only one drain or several of the same type of drain connected together.

An example of a complex drainage system would be:  A French Drain in the back yard connected to a Surface Drain near a flower bed connected to several gutter downspouts, which are connected to a Channel Drain going across a driveway, which is connected to additional Surface Drain in the front yard, which runs to a Curb Fitting that lets all the water drain out on to the street.

A simple Drainage System might consist of a Surface Drain that is connected to a second Surface Drain which runs to a Pop-up Emitter which lets water drain over the curb and into the street.

6 Inch French Drain Installation

Today we installed a 6 Inch French Drain at an apartment complex near Lake Heffner.  The French Drain started in the back yard of one unit.  The Drainpipe went under the fence and into the adjoining unit’s back yard.  The French Drain then looped around their patio and out under their fence to the west.  To get the 6-inch Drainpipe to the correct Exit Point, we had to cut out 30 feet of sidewalk and run the French Drainpipe under the sidewalk.

Next, we replaced the sidewalk with new concrete.  Finally, we dug a drainage ditch across the front yard to the parking lot.  We covered the Drainpipe with sod that we carefully removed when digging the trench.

We installed a 6-inch pop up emitter At the edge of the parking lot.   Seven Gutters were connected directly into the Drainage System along the way.

This particular Drainage System was made up of 55 Feet of 6-inch French Drain, 78 Feet of Solid ADS Solid Drainpipe, Seven Gutter Connections, and one 6-inch Pop-Up Emitter.

French Drain Installation and Channel Drains for Oklahoma City, Norman, Edmond, Moore

Posted: January 6, 2021 in Channel Drain, french drain
Tags: , , , ,
0

French Drain Installation, Oklahoma City, Norman, Moore, Edmond

Oklahoma Drainage — 405 203 9419- Servicing all of Central and Western Oklahoma

FRENCH DRAIN, SURFACE DRAIN PHOTOS AND INFORMATION

 

Channel Drain Install

Channel Drain Installation in the Patio Corner

 Standing water can cause many types of property damage ranging from foundation problems to cracked sidewalks and dead plants and shrubs.  If you have need of French Drain or Surface Drain, give us a call.  We provide free estimates for all of central Oklahoma.

 

French Drain With Colored Gravel in Oklahoma City

French Drain with Colored Gravel in Oklahoma City

 

 

Installing Cement around Curb Fitting for French Drain in Norman

Installing Cement around Curb Fitting for French Drain in Norman

Some Drainage Systems are complex and incorporate several types of drains.  Most Drainage Systems , however, are basic and require just one type of Drain. 

Oklahoma Drainage installs a variety of drains to solve a variety of problems. French Drains, Surface Drains, and Channel Drains are most commonly used. 

If you live in Edmond and need a Channel Drain installed across your driveway, or if you live in Norman and need a French Drain in your backyard, or if you live in Oklahoma City and need a Surface drain installed next to your sidewalk, we can help.

Channel Drain Installed by CMG In Yukon

Oklahoma Drainage provides Drainage Diagnostics.  A Drainage Diagnostic is a scheduled appointment where we come out and look at your Drainage Problem and get your input on the situation.  We look at all the variables that are causing your Water-Runoff Problems and design a Drainage System to solve it.  French Drains and Surface Drains are used to make up the Drainage System.

Channel Drain Installation in sidewalk in Oklahoma City
Channel Drain Installation in sidewalk in Oklahoma City

Typically many things must be considered when completing a Drainage Diagnostic.

1.  Identify the areas being damaged by water and determine if there are any hidden areas.

2.  Identify the sources of water causing the damage.  Most Drainage Problems have more than one source.  A water source can fall from the sky as rain, or can flow down the hill as storm-water runoff, or can flow from a gutter down-spout (yours or your neighbor’s),  or flow under ground as sub-surface water flow, or water can flow off a sidewalk, driveway, or street.  (These are the most common)

3.  Identify the Exit Point by determining where we want to take the unwanted water.

4.  Determine what type of Drains can best solve the Drainage Problem.  We utilize: French Drains, Surface Drains, Channel Drains, Trench Drains, and Sump Pumps.

5.  Determine what type and size of Drain Pipe is needed to accommodate the volume of water to be drained.  Larger is always better!  Big Drains with Small Drain Pipes never works!

If you have problems with Standing Water after a hard rain, or your driveway or sidewalk turns into a moat after a thunderstorm, or worst of all, you have water standing against your foundation and seeping into your house and vents, Give us a Call!  TYPICALLY A DRAINAGE SYSTEM IS MUCH LESS EXPENSIVE THAN FOUNDATION REPAIR OR REMOVING MOLD FROM YOUR HOME OR BUSINESS!!

Drainage System Installation, Gutter Down Spouts Connected.
Drainage System Installation, Gutter Down Spouts Connected.

Edmond French Drain, Oklahoma City French Drain, Norman French Drain, Moore French Drain–

Posted: July 12, 2020 in Edmond French Drain, french drain, French Drain Information, French Drain Photos, French Drain Repair
Tags: , , ,
12

French Drain Connected to Curb outlet

new curb outlet

Curb outlet with more than 6 inches of fall

 

Oklahoma Drainage and Sprinkler Repair 405 203 9419 — We provide:

    French Drain Installation, Surface Drain Installation, Drainage System Installation

    Sprinkler Repair for all aspects of Residential Sprinkler Systems

    

Drainage Systems, French Drains, Surface Drains, Channel Drains, Sump Pumps, Sprinkler Repair, with 26 years of experience. 

 

Just what is a “French Drain?” Many times, people incorrectly

use the phrase, “French Drain,” when they mean “Surface Drain” or “Channel Drain.”

 

A basic French Drain consists of a Perforated Drainpipe in the bottom of a trench. The French Drain Trench runs through a Problem Drainage Area that needs to be drained.   The French Drain Pipe is perforated (Full of Small Holes) and has Neo-Prene Soc around the pipe.  This soc helps prevent debris from clogging the French Drainpipe.

 

muddy french drain installation

Installing a French Drain in the mud

Standing water can cause a lot of damage to your yard.  The above picture was from a French Drain Installation in Oklahoma City.

Many times we wait until things dry out a bit before beginning a French Drain Installation.  Some times the water never goes away.  So we start digging in standing water and putting the mud in a wheelbarrow.   We then haul it to a dump trailer to be hauled away.  It isn’t the easiest thing to do.

Setting in the channel drain

Setting in the Channel Drain in the cut.

Installing concrete channel drain

Setting the concrete around the channel drain

Liner and French dran

Perforated Pipe, Filter , and Liner installed in a drainage trench.

The water started draining away as soon as we dug the Drainage Trench.  Once the Pipe and Limestone were installed, it drained away even faster.

Trench Liner

The trench liner allows sub surface water to pass through it and reach the French Drain Pipe.  The reason it is installed is to maintain the integrity of the drainage trench so it doesn’t collapse over time.  It also helps protect the pipe from filling up with mud or sand, clogging the French Drain.

Below is a picture of a French Drain that we had to take out and replace because it had no liner or filter around the Pipe.

clogged French Drain Pipe

result of French Drain Installed Incorrectly

Installing concrete channel drain

Setting the concrete around the channel drain

 

The French Drain Pipe shown above has a neo Preen soc around it to prevent sand and debris from clogging the French Drain.  The next step is to add the lime stone on top.

Other types of stone can be used as well.

colored gravel french drain

French Drain with colored gravel.’

 

FD River roc

A French Drain with River Rock

Types of Stone

 

The type of rock that covers a perforated French Drain Pipe can be just about any type of quality gravel or crushed stone.  Very small crushed stone or sand is not a good idea, however.  The water must be able to flow through the stone to reach the perforated pipe.

Drain Basin Connected into a French Drain and Several Gutters

Drain Basin Connected into a French Drain and Several Gutters

Servicing Central Oklahoma including: Oklahoma City, Norman, Edmond, Midwest City, Del City, Yukon, Mustang, Moore, Norman, Purcell, Newcastle, Blanchard and surrounding areas.

Just what is a “French Drain?”  Many times people incorrectly

use the phrase, “French Drain,”  to apply to many different types of Drains that could be used in a Drainage System.  The term is widely used and many times incorrectly connected to “Surface Drains,” or “Channel Drains.”

A Surface Drain has a grate that sits on top of a basin.  The basin is underground.  A Drain Pipe is connected underground to an outlet on the Drain Basin.  Storm-Water Drains through the grate into the Drain Basin.  Once in the Drain Basin, water travels out of the basin through a Drain Pipe.  The Storm-Water continues downhill in an underground Drain Pipe to an exit point.

THIS IS NOT A FRENCH DRAIN!

A Surface Drain may come in many different shapes or sizes.  The Drain Grate may be round or square.  Here is a picture of a common Surface Drain.

Surface Drain and Drain Pipe

A Channel Drain is a type of Surface Drain and many times is installed in concrete across sidewalks or driveways.

A French Drain is completely different from a Surface Drain.  A basic French Drain consists of a Perforated Drain Pipe in the bottom of a trench.  The Drain Pipe should have a neoprene sock around the Perforated Drain Pipe.   This is to ensure that the Drainpipe does not become clogged.

The dirt that was taken out to make the trench is hauled away.  It is replaced by some type of small stone or gravel depending on what is desired or available.  I prefer crushed 1 inch lime stone.  It is the most economical option in my area.  Pea Gravel or some other type of small stone can work just as well.

The lime-stone or gravel is placed in the trench on top of the perforated Drain Pipe and filled all the way to the surface (ground level).   In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drain Pipe or the Gravel are installed.  This helps maintain the integrity of the trench over time.  It also increases the cost of the French Drain and the amount of time to install it.  I install a trench liner in a French Drain about 20% of the time.  Most of the time a liner in not needed.

Definition

Just what is a “French Drain?”  Many times people incorrectly use the phrase, “French Drain,”  to apply to many different types of Drains that could be used in a Drainage System.  The term is widely used and many times incorrectly connected to “Surface Drains,” or “Channel Drains.”

A Surface Drain has a grate that sits on top of a basin.  The basin is underground.  A Drain Pipe is connected underground to an outlet on the Drain Basin.  Storm-Water Drains through the grate into the Drain Basin.  Once in the Drain Basin, water travels out of the basin through a Drain Pipe.  The Storm-Water continues downhill in an underground Drain Pipe to an exit point.

THIS IS NOT A FRENCH DRAIN!

A Surface Drain may come in many different shapes or sizes.  The Drain Grate may be round or square.  Here is a picture of a common Surface Drain.

Channel Drain

A Channel Drain is a type of Surface Drain and many times is installed in concrete across sidewalks or driveways.

Channel Drain

A French Drain is completely different from a Surface Drain.  A basic French Drain consists of a Perforated Drainpipe in the bottom of a trench.  The Drainpipe should have a neoprene sock around the Perforated Drainpipe.   This is to ensure that the Drainpipe does not become clogged.

The dirt that was taken out to make the trench is hauled away.  It is replaced by some type of small stone or gravel depending on what is desired or available.  I prefer crushed 1 inch lime stone.  It is the most economical option in my area.  Pea Gravel or some other type of small stone can work just as well.

Crushed Limestone

The limestone or gravel is placed in the trench on top of the perforated Drainpipe and filled all the way to the surface (ground level).   In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drain Pipe or the Gravel are installed.

This helps maintain the integrity of the trench over time.  It also increases the cost of the French Drain and the amount of time to install it.  I install a trench liner in a French Drain about 20% of the time.  Most of the time a liner in not needed

Drain Pipe running to street from French Drain

Drain Pipe running to street from French Drain

A French Drain is designed to handle a large volume of water and cover a large area. The Drain is anyplace the trench goes. It has many applications and can be used in many situations.  It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Down-Spouts connected to it.

French Drain Problem

The main downfall of a French Drain is, that they, for the most part aren’t very pretty.  They don’t look very nice in a yard once they are completed.
Depending on the area the French Drain is installed and the type of grass around the French Drain, will dictate whether grass grows over the lime stone.  Grass can grow up and through the gravel in the French Drain over time eventually covering the gravel.  This is Ok.  It won’t have a measurable effect on the performance of the drain.

Don’t Cover a French Drain with Dirt!

DONT COVER THE GRAVEL IN THE FRENCH DRAIN WITH DIRT.  THE FRENCH DRAIN WON’T WORK IF THE TRENCH IS CLOGGED WITH DIRT.  DON’T EVEN INSTALL IT IF YOU ARE GOING TO COVER IT UP WITH DIRT.  PUTTING DIRT OVER A FRENCH DRAIN IS LIKE PUTTING A CORK BACK IN A BOTTLE.

DECORATIVE STONE CAN BE USED TO COVER A FRENCH DRAIN AND THEY LOOK GREAT AND LAST A LIFETIME.

 

 

Home Drainage Problems, Norman French Drain, Moore French Drain, French Drain Repair

Posted: November 1, 2013 in Drain Installation, Drain Repair, french drain, Home Drainage Problems
Tags: , , , ,
0

Home Drainage Problems, Norman French Drain, Moore French Drain, French Drain Repair

Pictures of French Drains can be helpful!

Recently we installed a large French Drain System for a home in North Edmond.  Their gutters were dumping a huge amount of water into the flower beds.  Once in the flower beds, the water traveled down into the foundation and filled up the air conditioner vents.  We installed a large French Drain with 6-inch perforated pipe.  The gutter down spouts were removed and the gutters were run straight into the French Drain Pipe.

 

Gutter connected straight into French Drain System

Gutter connected straight into French Drain System

Fixing Home Drainage Problems can be difficult.

Oklahoma Drainage installs a wide variety of drains to solve a wide variety of Drainage Problems. If you need a Channel Drain installed across a sidewalk, We can help. If water is seeping into your foundation, A French Drain could solve the problem. If water is standing in a low spot in your backyard, a Surface Drain will be a good addition.

Drainage Problems are common with many homes in Oklahoma.  Storm-water run-off can cause damage to foundations, driveways, and sidewalks.  It can also ruin expensive plants and trees and yards.

Large 6 Inch French Drain Installed in Norman

Large 6 Inch French Drain Installed in Norman

 

 

French Drains, Oklahoma City, Norman, Edmond. French Drain Repair

Posted: July 15, 2010 in Drain Installation, Drain Repair, french drain, French Drain Information, French Drain Installation
Tags: , , ,
11

French Drain or Surface Drain? So you have water in a place in your home or business that is causing a problem.  Maybe you have water standing on your sidewalk or leaking into your air conditioning ducts.  You might have water running under your garage door and flooding your garage.  You might have standing water that kills grass or plants in your yard.  There are an endless number of possible water drainage issues. Oklahoma Drainage and Sprinkler Repair has provided solutions for water drainage problems since 1993. We utilize French Drains and many types of Surface Drains to solve all types of Residential and Small Business water problems.  We also install Sump Pumps when water can not be drained from the problem area. As of January 2021 we have provided service for 5467 customers in Oklahoma.  Our service area includes all of Central and Western Oklahoma.  We will service other areas of Oklahoma by special appointment. There is never any cost for us to come and look at your water problems.

Give us a call for a free Estimate at 405 203 9419 or E-Mail — frenchdrain.sprinklerrepair@gmail.com

Installing concrete channel drain

Setting the concrete around the channel drain

French Drain install front

French Drain Installation in Edmond

  • French Drain on left
    French Drain Running on the side of the house
  • TRench
    French Drain trench
  • Installing concrete channel drain
    Setting the concrete around the channel drain
  • Setting in the channel drain
    Setting in the Channel Drain in the cut.
  • Surface Drain Installation as part of a Drainage System
  • new curb outlet
    Curb outlet with more than 6 inches of fall
 

 

 

 

 
Drainage Systems can be made up of one drain or a combination of many drains.  Drainage  problems can be very complex.   Complex Drainage Problems may require a combination of several different types of drains all inter-connected and working together.  Other times the drainage problem may be simple and straight-forward requiring only one drain or several of the same type of drain connected together. An example of a complex drainage system would be:  A French Drain in the back yard connected to a Surface Drain near a flower bed connected to several gutter downspouts, which are connected to a Channel Drain going across a driveway, which is connected to additional Surface Drain in the front yard, which runs to a Curb Fitting that lets all the water drain out on to the street. A simple Drainage System might consist of a Surface Drain that is connected to a second Surface Drain which runs to a Pop-up Emitter which lets water drain over the curb and into the street. An “Exit Point” is the term used for where all the water leaves the Drainage System.  Determining the Exit Point is very critical.  It is one of the first things we do when diagnosing a Drainage Problem. Drainage Systems can: 1.  Keep water away from foundations — A French Drain is best because it can move Surface Water and Sub-Surface Water (water moving under ground) away from the foundation.  Many times less experienced companies install Surface Drains to keep water away from foundations.  This can be a big mistake.  A Surface Drain can’t move or drain Sub-Surface Water.   Also A Surface Drain often can’t move enough water fast enough and easily becomes overwhelmed during a heavy rain.  A Surface Drain also can’t cover or protect a broad enough area. Surface Drains should be designed in a Drainage System to be located in smaller Drainage Areas moving moderate amounts of water.  Surface Drains look better than French Drains.  If ,”appearance” is more important than Drainage Capacity, Go with the Surface Drain.  Just know what you are getting into and what your expectations should be. One side of a foundation alone,  can be over 100 feet.  A 4 inch or 6 inch French Drain is best when protecting a large area such as a foundation.
Surface Drain Installed next to sidewalk in Oklahoma City.
Surface Drain Installed next to sidewalk in Oklahoma City.
2.  Keep water away from small or enclosed areas.  This might be a low area just through a gate on the side of a house, or the low area between a flowerbed and the wall of a house, or standing water on or near a sidewalk or driveway.  These types of Drainage Problems are best served with Surface Drains.  A Surface Drain can move water away from a low area that is relatively small.  This can occur in yards, flowerbeds, sidewalks and driveways.  A Surface Drain is designed to move Surface Water away from a problem area to a predetermined exit point.  Surface Drains are available in many sizes.  How quickly they remove standing water is usually determined by the size of the Drain Pipe that is connected to the Drain. Simply put, a Drainage System is one or a group of underground Drain Pipes that take water away from a place that has water standing on it or flowing across it.  The water that is in the problem area, can be causing damage or may be inconvenient or both.  (Usually Both)  A simple Drainage System is a Drain for the water to enter, a Drain Pipe to move the water away from the Drain, and an Exit Point for the water to be released out of the Drain Pipe. Recently we installed a large 6 inch French Drain in a home in North West Edmond.  The home owner was getting water in their floor Duct Work every time it rained.  Installing a large French Drain along the wall in their flower bed solved the problem.  No longer is water seeping into their foundation and coming up in their vents.
Connecting Gutters into a Drainage System is a good idea!
Connecting Gutters into a Drainage System is a good idea!