Sprinkler Controller Repair Norman

Posted: December 9, 2025 in Sprinkler Controller, sprinkler repair, Sprinkler Repair Service, Sprinkler Service
Tags: , ,
3

Sprinkler Controller Repair Norman

is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Sprinkler Controller

Sprinkler Controller

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,     Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes – Sprinkler Head Adjustment – Sprinkler Valve Replacement

We provide Service for Folks in: Norman, Oklahoma City, Edmond, and Moore.

Central and Western Oklahoma is our Service Area since 1993.  

                                                           (405) 203-9419

 

Sometimes things go wrong with sprinkler systems.

 

 

One Common problem is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

 

Inside the valve box is a plastic handle that can turn off the water to the sprinkler system.  It can be blue or red or grey in color.

Many times, the valve box will be full of dirt, and you can’t turn or even see the handle until some of the dirt has been dug out by hand.

Water might be shooting up in the air somewhere on your property.  This can be caused by a broken sprinkler pipe or sprinkler valve.

SHUT OFF THE SPRINKLER WATER IF YOU CAN AND GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR. SERVICING ALL OF CENTRAL AND WESTERN OKLAHOMA.

405 203 9419

Servicing Oklahoma City, Norman, Edmond and all of Central and Western Oklahoma

 

Sprinkler Valve Repair Oklahoma City

Posted: December 8, 2025 in sprinkler repair, sprinkler repair contractor, sprinkler repair Oklahoma city, Sprinkler Valves
Tags: , , ,
3

Sprinkler Valve Repair Oklahoma City.   Oklahoma Drainage and Sprinkler Repair has provided Expert Sprinkler Valve Repair and Replacement since 1993.

What Is a Sprinkler Valve?

Think of a Sprinkler Valve as an “Off or On” Switch.    The Sprinkler Controller   turns the valves on or off.

It Sends a signal through a wire which is underground to the sprinkler valve somewhere in your yard.

Once turned on, the valve lets water pass through a sprinkler pipe to a specific group of sprinkler heads called a Sprinkler Zone.  The controller allows water to reach the sprinkler heads for a certain amount of time running through the sprinkler valve.  Once the time is up, it shuts off the sprinkler valve and moves on to the next valve in sequence.

Think of it as walking into every room in your house one at a time.  As you enter you turn on the light.  As you leave you turn off the light and move to the next room. You are the controller.  The light switch represents the sprinkler valve.

What causes a Sprinkler Valve to stop working?

Sprinkler Valve Replacement

Sprinkler Valve Replacement

Like anything else, a sprinkler valve can wear out.   Sprinkler valves fail in closed position.  It won’t run continuously if it breaks.

Sprinkler Valves get stuck while running sometimes.   The water supply must be then turned off to stop the Sprinkler from running.

Sprinkler Valves can freeze and break in the winter if the sprinkler system has not been properly drained for winter’s cold.

(winterized)

Tree roots can twist or break sprinkler pipes running into sprinkler valves.  Magnolia Trees are really bad about this.  Oak trees can cause damage too.

Driving something heavy across your yard can crush sprinkler valves.  Usually riding lawnmowers don’t cause damage but any truck or car will if you drive over a valve.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provides Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

 

Sometimes things go wrong with sprinkler systems.

 

Rotor Sprinkler Head

Rotor Sprinkler Head in Action

 

One Common problem

is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

Blanchard French Drain, French Drain Repair, Service, Installation

Posted: December 8, 2025 in french drain, French Drain Information, French Drain Installation, French Drain Repair, French Drain Service
Tags: , ,
1

Blanchard French Drain.  Oklahoma Drainage and Sprinkler Repair has provided Expert Service and Installation in Blanchard since 1993.

Many times, people believe that a French Drain has a Grate on the Top.  It does not.

The Picture above is a Surface Drain.

French Drain – A French Drain is a perforated pipe that is basically full of slits or holes.  A trench is dug across the problem drainage area.   A Semi-permeable liner is placed in the trench which lets in water but not dirt. The dirt from the trench is hauled away.   The French Drainpipe has a Neo-Preen Soc around it witch also lets in water but keeps the dirt out.

The perforated pipe is placed in the trench.  The Drainage trench is dug deep enough so that the perforated French Drainpipe is several inches below ground level when placed in the trench.  Next gravel or some type of crushed stone is placed on top and around the French Drain perforated pipe until the trench is full.

 

 

 

A basic French Drain consists of a Perforated Drainpipe in the bottom of a trench. The French Drain Trench runs through a Problem Drainage Area that needs to be drained.   The French Drainpipe is perforated (Full of Small Holes) and has Neo-Prene Soc around the pipe.  This soc helps prevent debris from clogging the French Drainpipe.

 

The dirt that was taken out to from the trench is hauled away. It is replaced by some type of small stone or gravel depending on what is desired or available.

Gravel or Crushed Limestone

I prefer crushed 1 inch limestone. It is the most economical option in my area. Pea Gravel or some other type of small stone can work just as well. The limestone or gravel is placed in the trench on top of the perforated Drainpipe and filled all the way to the surface (ground level).

In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drainpipe or the Gravel are installed. This helps maintain the integrity of the trench over time. It also increases the cost of the French Drain and the amount of time to install it. It is a good practice to always install a Trench Liner.

 

A French Drain is designed to handle a large volume of water and cover a large area. The Drain is anyplace the trench goes. It has many applications and can be used in many situations. It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Down-Spouts connected to it.

The main downfall

of a French Drain is that they, for the most part isn’t very pretty. They don’t look very nice in a yard once they are completed.

Depending on the area the French Drain is installed and the type of grass around the French Drain, will dictate whether grass grows over the limestone. Grass can grow up and through the gravel in the French Drain over time eventually covering the gravel. This is Ok. It won’t have a measurable effect on the performance of the drain.

DONT COVER THE GRAVEL IN THE FRENCH DRAIN WITH DIRT. THE FRENCH DRAIN WON’T WORK IF THE TRENCH IS CLOGGED WITH DIRT. DON’T EVEN INSTALL IT IF YOU ARE GOING TO COVER IT UP WITH DIRT.

DECORATIVE STONE CAN BE USED TO COVER A FRENCH DRAIN AND THEY LOOK GREAT AND LAST A LIFETIME.

WHERE WE HAVE WORKED!

In 1993 we had no website.  I stuck little signs on the side of the road as advertisement.  I got my first Drain Installation work in March of 1993 in Norman.  It was in Brookhaven North of Robinson Street on the West side of I 35.

Over the years Oklahoma Drainage and Sprinkler Repair has installed all types of Drainage Systems in almost Every town in Central and Western Oklahoma.

The majority of our customers live in Oklahoma City, Norman, Edmond, Yukon, Mustang, Moore, Midwest City, Del City, Blanchard, New Castle, Yukon and Choctaw.

Oklahoma Drainage and Sprinkler Repair hasn’t been limited to those areas, however.  We have also installed French Drains, Surface Drains, Channel Drains, and Sump Pumps in many other cities.

Working Drainage Systems Installed by Oklahoma Drainage also reside in: Lawton, Duncan, Ardmore, Chickasha, Shawnee, Enid, Weatherford, Elk City, El reno and many other places.

If you live in any of these Cities or towns, we have installed a French Drain, Surface Drain, Channel Drain, or Sump Pump within 5 miles of your home.

Here is a description of other recent work.

A little bit North of Downtown Oklahoma City, Oklahoma Drainage installed a 6-inch French Drain between two businesses which were less than three feet apart.  The French Drain went between a Law Firm and a Tire shop.  Water was leaking through the walls of both businesses.  Gutters between the two establishments were dumping a huge amount of water.  We installed a 6-inch French Drain between the gutters.

It took a long time to get the dirt out of the trench for the French Drain.  It was a very tight fit.  We had to use a little red wagon to haul out the dirt for the French Drain and haul back in the crushed limestone for the French Drain.  It looked a little silly, but it was the only thing we could find that was narrow enough to fit between the buildings.  A French Drain that normally would take 1 day to install took three.

Oklahoma Drainage and Sprinkler Repair has been installing French Drains in Newcastle since 1993.  We have helped over 4000 customers in Central and Western Oklahoma.
We install: French Drains, Surface Drains, Channel Drains and Sump Pumps.  Sprinkler Repair and Sod Installation are Also Available.

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes – Sprinkler Head Adjustment – Sprinkler Valve Replacement

Servicing all of Central and Western Oklahoma since 1993.

Oklahoma Drainage and Sprinkler Repair – French Drain Installation, Drainage System Design, Expert Lawn Sprinkler Repair, Drain Repair 

Recently Oklahoma Drainage and Sprinkler Repair installed a large 6-inch French Drain in Edmond.  The customer had water running under his back porch step and into his basement.

We did a Free Drainage Diagnostic and Estimate.  The French Drain design that we proposed would intercept the surface water and subsurface water that was flowing under the steps.

The French Drain design called for a 6-inch French Drain to be installed above and several feet away from the steps.  It would run around the house parallel to the foundation and about 5 feet to the East.  The French Drain would run past the steps to a point where water must cross the French Drain or run up hill to the steps which in this case was not possible.

 Once past the steps, the French Drain would transition to Solid 6-inch Drainpipe and continue on around the house to the Pop-Up Emitter downhill in the side yard.  Along the way we attached several Gutter Down Spouts into the French Drain.

 

Channel Drain Installation require a high level of Experience and attention to detail.

Curb Outlet for French Drain in Edmond

Curb Outlet for French Drain in Edmond

French Drain Installation

Oklahoma Drainage and Sprinkler Repair has been diagnosing and solving Drainage Problems since 1993.  Water has the ability to get into places around your home where you really don’t want it to be.  Some drainage problems are easy to solve.

Typically water enters the problem drainage area one way from one source.  The really tricky drainage problems occur when water enters the problem drainage area from multiple directions and from multiple sources.  Sometimes a secondary water source can’t be seen or identified until the primary water problem source is eliminated.

An example of this occurs when water is running into a problem area in an obvious way over the ground where you can see it.

Simple enough.

A drainage system is installed with a surface drain as the “intake” with drainage pipe running to an exit point.  Initially the water drains away, and everything looks great.

The next day water is back and is all around the surface drain, but below the edge and it hasn’t rained at all, so no additional water ran over the surface of the ground to flood the area.

The primary water source was solved, ( The surface water run off ) but the secondary water source was not.  Which was sub-surface water, (ground water) running into the area.  A surface drain can’t drain “ground water.”  A French Drain should have initially been installed instead of a Surface Drain.  A French Drain can drain both Surface Water and Ground Water.

 

A French Drain Can Handle Standing Water

 

Oklahoma Drainage and Sprinkler Repair

Services all of Central Oklahoma including Norman, Moore, Edmond, Yukon, Mustang, Oklahoma City, Midwest City, Del City, Blanchard, Newcastle, Purcell and Chickasha.

 

Keep water off your driveway with a channel drain

 Standing water comes from many sources.  It causes damage to sidewalks, driveways, and foundations not to mention plants, trees, and grass. 

Does the side of your house flood because your neighbor doesn’t have gutters. Is your sidewalk turning into a moat after a heavy rain? Worst of all, is water seeping into your foundation and duct work after a thunderstorm? 

These are just a few of the Drainage Problems that Oklahoma Drainage and Sprinkler Repair can help with.  We can design a Drainage System to fit your specific needs. 

We install many types of Drains to solve many types of problems.   

French Drains, Surface Drains, Channel Drains, Basement Drains, Trench Drains, Basin Drains, and Sump Pumps are utilized.

 

 

 

Just what is a “French Drain?”  Many times, people incorrectly

use the phrase, “French Drain,” to apply to many different types of Drains that could be used in a Drainage System.  The term is widely used and many times incorrectly connected to “Surface Drains,” or “Channel Drains.”

A Surface Drain has a grate that sits on top of a basin.  The basin is underground.  A Drainpipe is connected underground to an outlet on the Drain Basin.  Stormwater Drains through the grate into the Drain Basin.  Once in the Drain Basin, through a Drainpipe.  The Stormwater continues downhill in an underground Drainpipe to an exit point.

THIS IS NOT A FRENCH DRAIN!

A Surface Drain may come in many different shapes or sizes.  The Drain Grate may be round or square.  Here is a picture of a common Surface Drain.

Surface Drain with a Black Grate

Cutting the Curb

Cutting the Curb for a French Drain Outlet

A Channel Drain is a type of Surface Drain, and many times is installed in

Channel Drain
 

4 Inch Drain Pipe Ready to be covered with dirt in Norman.
4 Inch Drainpipe Ready to be covered with dirt in Norman.

 

 

Sump Pump Contractor Norman

Posted: December 7, 2025 in french drain, Sump Pump, Sump Pump Installation, Sump Pump Repair, Sump Pump Service
Tags: , , ,
0

Sump Pump Contractor Norman.  Oklahoma Drainage and Sprinkler Repair has provided Sum Pump  Service and Installation in Norman since 1993

Oklahoma Drainage and Sprinkler Repair– 405 203 9419 — We Install and Service Sump Pumps, Channel Drains, Sprinkler Repair and

    French Drain Installation, Surface Drain Installation, Drainage System Installation

Oklahoma Drainage Installs Surface Drains and French Drains.  Sometimes it is up hill in all directions from the Problem Drainage Area.  This problem can be solved by installing a Sump Pump.  When the cavity fills, the water is pumped away to the point where the water exits the drain which can be a curb outlet or a pop-up emitter.

Sump Pump Installation
Sump Pump Installation 

When you have a low-lying area that needs a French Drain, but it is up-hill in all directions and there is no way for the French Drain to move water to the Exit Point, a Sump Pump can be used.

Sump Pumps can also be used to pump water out of Basements or other enclosed low-lying areas.  Most Residential applications require a sump pump that has a power rating of 1 horse to 2 horse.  (Horse being horsepower)

Sump Pump Installation

Sump Pumps are used when water can’t be drained away by gravity.  You might have water standing in an area and it is up hill in all directions.

French Drains, Surface Drains, Channel Drains and Gutters can all be connected to a Sump Pump.

They can be connected exclusively or as a group.

A gravity flow French Drain or Surface Drain System will not work so you must pump the water to the Exit Point.  The Same holds true if you have water standing in a basement.  Pumping out the water is the only way.

Most Sump Pumps work automatically.

When the Sump Pump is under water a float rises up on the side of the pump and turns on the pump.  The water is pumped away, the float falls back down and turns off the pump.  When water is flowing constantly on to the pump, it turns itself on and off over and over.  This could go on for hours or even days.

Sump Pump Inside Sump Cavity

Sump Pump Inside Sump Pump Cavity

Two Sizes of Sump Pumps

Pump Size refers to how powerful it is not how physically large it is.  For Home or Small Business use a 1/3 Horse or a 1/2 Horse Works Best.  Larger Pumps such as a 1 Horse Pump must be ordered by a supplier and must be Hard Wired to 220 voltage by an electrician.

A Sump Pump Cavity looks like a trash can.  When water drains into the sump cavity it raises the float and turns on the pump. Once empty it falls down and turns off the Pump.

The larger the sump cavity the less often the sump turns on and off.   A small sump cavity wears out the sump pump faster because it turns on and off more making it less efficient.

 

Larger Sump Cavity

Clean Water

A “Clean” pump must pump water that is relatively clean, or it will clog up after a while.

A” Dirty” Pump can handle water that is not so clean that has small pieces of Debris in it.

It will also clog if the debris is too thick or large.

There are several techniques that Oklahoma Drainage uses to keep a sump pump “Clog Free” and running well.

One technique is to place the sump pump on top of a cement block inside the pump cavity.  Debris and unwanted solids fall the bottom of the sump cavity and never goes through the sump.  The sump cavity must then be cleaned out on a regular basis depending on the usual amount of debris.

Once a Year is typical.  Also putting a sump pump under a tree is a bad idea.  Leaves will clog up a sump faster than anything.  Pine needles are the worst.

Below is a Sump Pump connected to a Channel Drain.  The Sump Cavity is buried in the in the area where the dirt is disturbed.  As seen in the following picture.

The Homeowner had a Sump Pump

in their basement that was fed from a French Drain outside the Basement Wall.  The French Drain was 14 feet down along the Stem wall of the house.  The French Drainpipe was cheap and had collapsed.  We brought in a Mini Excavator and dug up the pipe and replaced it with Durable ADS 4 inch perf/soc French Drain pipe.  In the end, we were able to dig up the pipe and replace it.

Next, we installed a new exit for the water by installing a curb fitting.

No more flooding in the customers basement.  A few weeks later our customer was able to lay carpet in the basement with no problems.

Sump Pump Installation is necessary when water from a Drainage System can’t flow properly.  This means it is uphill in every direction from the Drain Intake.

 

 

French Drain Running Through Low Areas

French Drain with stepping stones

WHAT SIZE DRAINPIPE FOR FRENCH DRAINS?

French Drains can be decorated with many types of stone
French Drains can be decorated with many types of stone

French Drains can utilize several types and sizes of French Drainpipe.  An older type that is not commonly used any more is 4 inch PVC Pipe with large half inch holes drilled in the Pipe.  This doesn’t work very well,   Because the holes are too large and the number of holes in the French Drainpipe are too few. Also there is no filter or “Soc” around this particular French Drainpipe.  If it is used in sandy or loose soil the holes will clog and the pipe will fill up with sand.  PVC French Drainpipe should be avoided.

ADS French Drainpipe

is much better, the holes are smaller and much more numerous.  It also comes inside a soc that acts as a filter and helps keep sand and debris out of the French Drainpipe.  It works very well.

French Drain in flowerbed
French Drain in flowerbed

For Small business and Residential French Drains, four-inch ADS Perf/Soc French Drainpipe is adequate and the most common.  It is used for the majority of all French Drains installed.  French Drains can be installed using 3 inch ADS Perf/Soc but many times it is too small and can be overwhelmed by a heavy rain or from a bad design.  (Too many gutter down spouts connected directly into the French Drain, For Example) Three Inch French Drainpipe should be avoided if possible.

Six inch  ADS Perf/Soc French Drainpipe is usually a good idea when possible.  It carries a much larger volume of water.  Six Inch French Drains are rarely overwhelmed.

NDS Channel Drain Composite Grey Connected to 4 Inch ADS Solid Drain Pipe

Driveway Channel Drain

Edmond Sump Pump Service

Posted: December 6, 2025 in french drain, Sump Pump Installation, Sump Pump Repair, Sump Pump Service
Tags: , ,
5

Edmond Sump Pump Service. Oklahoma Drainage and Sprinkler Installs and services Sump Pumps. 

Our first sump pump installation was in Norman in 1993 on the West side in Brookhaven.

Recently we serviced a Sump Pump for a customer who lives off of Memorial Rd. 

The Sump Pump Float was stuck on the side of the sump cavity. We turned The Sump Pump to free up the float.  In this case the pump did not need to be replaced and continued to work just fine!

Sump Pumps are the only way to get water out of a basement. A French Drain or A Surface Drain Needs a Sump Pump when it is up hill in all directions from the drain.  When water can’t flow downhill to the exit of a Channel Drain, a Sump Pump is needed.

Do you have water standing in your yard, on your driveway, on your sidewalk, in your basement, or leaking into your home?

Oklahoma Drainage and Sprinkler Repair – can help with the installation of a: French Drain, Surface Drain, Channel Drain, Basement Drain, Trench Drain, Basin Drain, or Sump Pump.  We will Diagnose your Drainage Problem and Design a Drainage System Just for your needs.

We also provide Expert Sprinkler Repair.  Sprinkler Valves, Sprinkler Heads, Controllers, we service it all.

Oklahoma Drainage and Sprinkler Repair now also installs or repairs Frost Free Facets.

We service all of Central and Western Oklahoma. Sump Pumps can be connected to French Drains.  When you have a low-lying area that needs a French Drain, but it is up-hill in all directions and there is no way for the French Drain to move water to the Exit Point, a Sump Pump can be used. Sump Pumps can also be used to pump water out of Basements or other enclosed low-lying areas.  Most Residential applications require a sump pump that has a power rating of 1 horse to 2 horse.  (Horse being horsepower)

Clean Water

A “Clean” pump must pump water that is relatively clean, or it will clog up after a while. 

A” Dirty” Pump can handle water that is not so clean that has small pieces of Debris in it.  It will also clog if the debris is too thick or large. 

There are several techniques

that Oklahoma Drainage uses to keep a sump pump “Clog Free” and running well. One technique is to place the sump pump on top of a cement block inside the pump cavity. Debris and unwanted solids fall the bottom of the sump cavity and never goes through the sump.  The sump cavity must then be cleaned out on a regular basis depending on the usual amount of debris. Once a Year is typical.  Also putting a sump pump under a tree is a bad idea.  Leaves will clog up a sump faster than anything.  Pine needles are the worst.

Below is a Sump Pump connected to a Channel Drain.  The Sump Cavity is buried in the in the area where the dirt is disturbed.  As seen in the following picture.

 

Sump Pump connected to a French Drain.  

Two Sizes of Sump Pumps

Pump Size refers to how powerful it is not how physically large it is.  For Home or Small Business use a 1/3 Horse or a 1/2 Horse Works Best.  Larger Pumps such as a 1 Horse Pump must be ordered by a supplier and must be Hard Wired to 220 voltage by an electrician.

Oklahoma Drainage and Sprinkler Repair install a variety of other types of Drains. 

 
 
In the past 32 years, we have installed French Drains to keep water away from home and business foundations, Surface Drains to keep water away from sidewalks and driveways, Trench Drains, and French Drains to keep standing water out of flowerbeds and yards, and Sump Pumps to remove water from basements and outdoor low-lying areas.

 

 

Sprinkler System Checkup Edmond, Service, Repair,

Posted: December 5, 2025 in Sprinkler Checkup, sprinkler repair, Sprinkler Service
Tags: , , ,
0

SSprinkler System Checkup Edmond, Service, Repair

Lots of things can be done to make sure your Sprinkler System is ready to go.  All the Sprinkler Zones should be checked one by one.  The sprinkler heads and valves need to be checked to see if anything needs to be adjusted or replaced.

Sprinkler System Checkup is a Service Provided by Oklahoma Drainage since 1993.

Today we did a sprinkler repair in Norman.  The sprinkler system needed a checkup.

We went through each sprinkler zone and identified several different problems.

Zone 2 had a cracked sprinkler pipe in a flower bed.

A broken Rotor Sprinkler head was found immediately.

Spraying Rotor Sprinkler Repair

Spraying Rotor Sprinkler Head

Next, zone five look good with no problems.

Zone 6 and 7 each had a couple of pop-up spray heads that were worn out and would not pop-up.  The diagnosis and the repair took less than two hours.  Now their sprinkler system is running great!

Now is a good time to have a Sprinkler System Checkup provided by Oklahoma Drainage.

Sprinkler Systems need to be checked before winter to prevent pipes from freezing.  Sprinkler Design determines whether sprinkler lines need to be bled.  Emergency shut off valves also need to be checked and turned off for the winter.

In the Spring, all the water needs to be turned back on and all sprinkler zones and heads need to be tested.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provide Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

Sprinkler Valves

A Sprinkler zone is turned on or off by a Sprinkler Valve.  Sometimes they stick on or off.  They can wear out and quit working too.

 

Sprinkler Valve Replacement is a service that Oklahoma Drainage has provided Since 1993.  Recently we removed 3 Rainbird Sprinkler Valves and replaced them with new ones.  The valves had been crushed accidentally when a landscaper drove his truck across the yard.

Sprinkler System Check-Up in Edmond, Oklahoma City, Norman, and Moore.

 

 

Sprinkler System Check-Up process is very straightforward.  We run through all the Sprinkler Zones one-at-a- time from the controller. 

Sprinkler Controller

Sprinkler controllers can be a problem source.   Many times, the wires in the controller are loose or have a “Short” in one of the wires.  Sprinkler Programming can be a source of frustration.  We can help with Programming your controller.

We check all the sprinkler heads in that zone and the valves as well.

Once the Sprinkler System Checkup is Complete, we provide a Quote for what it will cost to make the needed repairs.

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes – Sprinkler Head Adjustment – Sprinkler Valve Replacement

Servicing all of Central and Western Oklahoma since 1993.  405 203 9419

Sprinkler Valve Replacement is a service that Oklahoma Drainage has provided Since 1993.  Recently we removed 3 Rainbird Sprinkler Valves and replaced them with new ones.  The valves had been crushed accidentally when a landscaper drove his truck across the yard.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provide Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

First Step

First, we dug up a good working area surrounding the broken Sprinkler Valves.  Next, we cut out the broken valves and crushed PVC pipes.  Finally, PVC pipe was cut and glued with new Sprinkler Valves following the original design and configuration.  In this case the three original sprinkler valves were connected to each other inside one Valve Box.

We aren’t done yet though; two sprinkler wires must be connected to each Valve.  One sprinkler wire is the “Common Ground.”  The other wire is the power wire.  All the sprinkler wiring is connected with water-proof wire connections.

The Common Ground wire and the Individual Power Wires all come from the Sprinkler Controller.  Each Sprinkler Valve has its own power wire coming from the Controller.  All the Sprinkler Valves are Connected to the Same Common Ground Wire.

Sprinkler Valve Replacement

Oklahoma City Sprinkler Repair

Before We Finish

Before dirt can be put back around the new valves, testing must be done.  Each valve must be turned on, “one-at-a-time,” at the Controller to ensure good wire connection and functionality.  Also, the Sprinkler Valves must be checked for leaks in the PVC Pipe.

Oklahoma Drainage and Sprinkler Repair provides Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

Blanchard Sprinkler Repair has been provided by Oklahoma Drainage and Sprinkler Repair since 1993.

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

A Sprinkler Controller can be a big “Headache,” for a Homeowner.

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,     Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

Sprinkler Head Installation

Sprinkler Head Installation

French Drain Contractor Moore Oklahoma, Sprinkler Repair, Sump Pumps

Posted: December 3, 2025 in french drain, French Drain Contractor, French Drain Repair, French Drain Service
Tags: , , ,
2

French Drain Contractor Moore Oklahoma.

Oklahoma Drainage – 405 203 9419 — Servicing all of Central and Western Oklahoma

Moore Oklahoma French Drain Contractor

Our Drainage Systems utilize French Drains, Surface Drains, Channel Drains, and Sump Pumps.   With over 33 years of experience we provide top quality French Drains, Drainage Systems.

Check Out Our Helpers!

Just what is a “French Drain?” Many times, people incorrectly

use the phrase, “French Drain,” when they mean “Surface Drain” or “Channel Drain.”

 

A basic French Drain consists of a Perforated Drainpipe in the bottom of a trench. The French Drain Trench runs through a Problem Drainage Area that needs to be drained.   The French Drainpipe is perforated (Full of Small Holes) and has Neo-Prene Soc around the pipe.  This soc helps prevent debris from clogging the French Drainpipe.

The dirt that was taken out to make the trench is hauled away. It is replaced by some type of small stone or gravel depending on what is desired or available.

I prefer crushed 1 inch limestone. It is the most economical option in my area. Pea Gravel or some other type of small stone can work just as well.

The limestone or gravel is placed in the trench on top of the perforated Drainpipe and filled all the way to the surface (ground level). In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drainpipe or the Gravel are installed.

This helps maintain the integrity of the trench over time. It also increases the cost of the French Drain and the amount of time to install it. I install a trench liner in a French Drain Every time.

A French Drain is designed

to handle a large volume of water and cover a large area. The Drain is anyplace the trench goes. It has many applications and can be used in many situations. It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Down-Spouts connected to it.

Surface Drain with French Drain

Surface Drain beside a French Drain with River Rock

Moore Oklahoma French Drain Contractor

The main downfall of a French Drain is that they, for the most part aren’t very pretty. They don’t look very nice in a yard once they are completed.

Drain Pipe for French Drain running under sidewalk

Drainpipe for French Drain running under sidewalk

 

Sprinkler Repair Oklahoma City.  Oklahoma Drainage and Sprinkler Repair has provided Expert Sprinkler Repair Service in OKC since 1993.

Sprinkler Valve Installation

Sprinkler Valve Installation

Today we did a sprinkler repair in OKC.  The sprinkler system needed a checkup.

We went through each sprinkler zone and identified several different problems.

Zone 2 had a cracked sprinkler pipe in a flower bed.

A broken Rotor Sprinkler head was found immediately.

Next, zone five look good with no problems.

Zone 6 and 7 each had a couple of pop-up spray heads that were worn out and would not pop-up.  The diagnosis and the repair took less than two hours.  Now their sprinkler system is running great!

Now is a good time to have a Sprinkler System Checkup provided by Oklahoma Drainage.

Sprinkler Systems need to be checked before winter to prevent pipes from freezing.  Sprinkler Design determines whether sprinkler lines need to be bled.  Emergency shut off valves also need to be checked and turned off for the winter.

In the Spring, all the water needs to be turned back on and all sprinkler zones and heads need to be tested.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provide Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

Sprinkler Valves

Sprinkler Valve Replacement is a service that Oklahoma Drainage has provided Since 1993.  Recently we removed 3 Rainbird Sprinkler Valves and replaced them with new ones.  The valves had been crushed accidentally when a landscaper drove his truck across the yard.

Sprinkler System Check-Up in Edmond, Oklahoma City, Norman, and Moore.

 

 

Sprinkler System Check-Up process is very straightforward.  We run through all the Sprinkler Zones one-at-a- time from the controller. 

Sprinkler Controller

Sprinkler controllers can be a problem source.   Many times, the wires in the controller are loose or have a “Short” in one of the wires.  Sprinkler Programming can be a source of frustration.  We can help with Programming your controller.

We check all the sprinkler heads in that zone and the valves as well.

Once the Sprinkler System Checkup is Complete, we provide a Quote for what it will cost to make the needed repairs.

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes – Sprinkler Head Adjustment – Sprinkler Valve Replacement

Servicing all of Central and Western Oklahoma since 1993.  405 203 9419

Sprinkler Valve Replacement is a service that Oklahoma Drainage has provided Since 1993.  Recently we removed 3 Rainbird Sprinkler Valves and replaced them with new ones.  The valves had been crushed accidentally when a landscaper drove his truck across the yard.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provide Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

First Step

First, we dug up a good working area surrounding the broken Sprinkler Valves.  Next, we cut out the broken valves and crushed PVC pipes.  Finally, PVC pipe was cut and glued with new Sprinkler Valves following the original design and configuration.  In this case the three original sprinkler valves were connected to each other inside one Valve Box.

We aren’t done yet though; two sprinkler wires must be connected to each Valve.  One sprinkler wire is the “Common Ground.”  The other wire is the power wire.  All the sprinkler wiring is connected with water-proof wire connections.

The Common Ground wire and the Individual Power Wires all come from the Sprinkler Controller.  Each Sprinkler Valve has its own power wire coming from the Controller.  All the Sprinkler Valves are Connected to the Same Common Ground Wire.

Sprinkler Valve Replacement

Oklahoma City Sprinkler Repair

Before We Finish

Before dirt can be put back around the new valves, testing must be done.  Each valve must be turned on, “one-at-a-time,” at the Controller to ensure good wire connection and functionality.  Also, the Sprinkler Valves must be checked for leaks in the PVC Pipe.

Oklahoma Drainage and Sprinkler Repair provides Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

Blanchard Sprinkler Repair has been provided by Oklahoma Drainage and Sprinkler Repair since 1993.

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,     Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

Sprinkler Valve

A valve is an off or on switch for a particular Sprinkler Zone.

You might need a Sprinkler Valve replaced.  Maybe it just needs to be adjusted?  We can adjust the solenoid or “Bleed,” the valve itself.  Debris might be stuck in it.

Oklahoma City Sprinkler Repair

Oklahoma City Sprinkler Repair Replacing Valve

What Is a Sprinkler Valve?

Think of a Sprinkler Valve as an “Off or on” Switch.    The Sprinkler Controller   turns the valves on or off.

It Sends a signal through a wire which is underground to the sprinkler valve somewhere in your yard.

Once turned on, the valve lets water pass through a sprinkler pipe to a specific group of sprinkler heads called a Sprinkler Zone.  The controller allows water to reach the sprinkler heads for a certain amount of time running through the sprinkler valve.  Once the time is up, it shuts off the sprinkler valve and moves on to the next valve in sequence.

Think of it as walking into every room in your house one at a time.  As you enter you turn on the light.  As you leave you turn off the light and move to the next room. You are the controller.  The light switch represents the sprinkler valve.

What causes a Sprinkler Valve to stop working?

Like anything else, a sprinkler valve can wear out.   Sprinkler valves fail in closed position.  It won’t run continuously if it breaks.

Sprinkler Valves get stuck while running sometimes.   The water supply must be then turned off to stop the Sprinkler from running.

Sprinkler Valves can freeze and break in the winter if the sprinkler system has not been properly drained for winter’s cold.

(winterized)

Sprinkler Head Adjustment

Many homeowners need sprinkler heads moved to a new location or caped if they are no longer needed.  A sprinkler head might be spraying in the wrong place.

 

Sprinkler Controllers also cause problems.  Setting the programming might be difficult for the Homeowner.  They can stop working correctly too.

Oklahoma Drainage can help with all of these problems and many others.  The problems listed above are the most common.

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

The Big Problem

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,     Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes – Sprinkler Head Adjustment – Sprinkler Valve Replacement

We provide Service for Folks in: Norman, Oklahoma City, Edmond, and Moore.

Central and Western Oklahoma is our Service Area since 1993.  

                                                           (405) 203-9419

 

 

 

Sprinkler Valve Repair Norman

Posted: December 2, 2025 in sprinkler repair, sprinkler repair contractor, Sprinkler Repair Service, Sprinkler Service, Sprinkler Valve Repair
Tags: , , ,
2

Sprinkler Valve Repair Norman.  Oklahoma Drainage and Sprinkler Repair has provided Expert Sprinkler Repair Service for Norman and all of Central and Western Oklahoma.

Sprinkler Valves are very important to any sprinkler system.  Unfortunately, many things can go wrong with a Sprinkler Valve.

Here is a short list:

Sprinkler Valves can Stick Open.  This means that when it’s time for the Sprinkler Zone to stop, it keeps running and won’t stop or shut off.

Sprinkler Valves can leak. This can be from the “PVC Pipe” Connections, or the “Bleed” Screw is loose.

Sprinkler Valve Wiring can short out or come loose.  All of a sudden, the Sprinkler Zone won’t work.

The above list are just the most common problems for Sprinkler Valves.

Sprinkler Valve Replacement

Sprinkler Valve Replacement

Sprinkler Valve Replacement is a service that Oklahoma Drainage has provided Since 1993.  Recently we removed 3 Rainbird Sprinkler Valves and replaced them with new ones.  The valves had been crushed accidentally when a landscaper drove his truck across the yard.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provides Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

First Step

First, we dug up a good working area surrounding the broken Sprinkler Valves.  Next, we cut out the broken valves and crushed PVC pipes.  Finally, PVC pipe was cut and glued with new Sprinkler Valves following the original design and configuration.  In this case the three original sprinkler valves were connected to each other inside one Valve Box.

We aren’t done yet though; two sprinkler wires must be connected to each Valve.  One sprinkler wire is the “Common Ground.”  The other wire is the power wire.  All the sprinkler wiring is connected with water-proof wire connections.

The Common Ground wire and the Individual Power Wires all come from the Sprinkler Controller.  Each Sprinkler Valve has its own power wire coming from the Controller.  All the Sprinkler Valves are Connected to the Same Common Ground Wire.

Before We Finish

Before dirt can be put back around the new valves, testing must be done.  Each valve must be turned on, “one-at-a-time,” at the Controller to ensure good wire connection and functionality.  Also, the Sprinkler Valves must be checked for leaks in the PVC Pipe.

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes – Sprinkler Head Adjustment – Sprinkler Valve Replacement

Servicing all of Central and Western Oklahoma since 1993.  405 203 9419

Emergency Sprinkler Repair

Sometimes things go wrong with sprinkler systems.

 

IF YOU NEED HELP IN THE MIDDLE OF THE NIGHT OR ON A WEEKEND WITH YOUR SPRINKLER SYSTEM, GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR.  405 203 9419

IT MAY TAKE A FEW HOURS FOR US TO GET THERE BUT WE WILL COME TO HELP.

 

One Common problem is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

 

Inside the valve box is a plastic handle that can turn off the water to the sprinkler system.  It can be blue or red or grey in color.

Many times, the valve box will be full of dirt, and you can’t turn or even see the handle until some of the dirt has been dug out by hand.

 

Water might be shooting up in the air somewhere on your property.  This can be caused by a broken sprinkler pipe or sprinkler valve.

SHUT OFF THE SPRINKLER WATER IF YOU CAN AND GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR. SERVICING ALL OF CENTRAL AND WESTERN OKLAHOMA.

405 203 9419

Servicing Oklahoma City, Norman, Edmond and all of Central and Western Oklahoma

 

Oklahoma Drainage Installs Drainage Systems,  and provides Expert Sprinkler System Repair.

Our Drainage Systems utilize French Drains, Surface Drains, Channel Drains, and Sump Pumps.  

We Service all of Central Oklahoma including: Norman, Moore, Edmond, Yukon, Mustang, Oklahoma City, Midwest City, Del City, Blanchard, Newcastle, Purcell and Chickasha.

Back-Flow-Valve Service, Sprinkler Repair

Oklahoma Drainage and Sprinkler Repair Provides Service for Back-Flow-Valves and all types of Lawn Sprinkler Repair and Service.  We have provided Expert Service for all of Central and Western Oklahoma Since 1993.

Back-Flow-Valves

There are two types of Back-Flow-Valves.

Above Ground

Above Ground Back-Flow-Valve

Above Ground Back-Flow-Valve.

 

Below Ground Back-Flow-Valve.

Below Ground Back-Flow-Valve

Below Ground Back-Flow-Valve

What is a Back-Flow-Valve?

A Back-Flow-Valve is a part of a Lawn Sprinkler System.  Water passes through it from the water source which can be a Water Meter or a Well Pump.  It forces water to travel in only one direction from the source to the sprinkler system.  It can’t travel backward back to the water source which again is a water meter or well pump.

A Back-Flow-Valve provides protection to the water source from back pressure and chemical contamination from lawn fertilizer.

Most Cities require a Back-Flow-Valve as “Code” for Sprinkler Installation.

Emergency Shut off

Back-Flow-Valves usually have an Emergency Shutoff valve on them that can shut off the water to the lawn sprinkler system but keep the water turned on to the home. Most Back-Flow-Valves have two Emergency Shut off Handles.  Either one will work.  Many times, they are hard to turn, however.

If there is a leak or water is shooting up in the air just turn the valve handle and give us a call.

In ground Back-Flow-Valve

Blue Emergency Shutoff handles for a Back-Flow-Valve.

Norman Sprinkler Checkup is a Central Focus for Oklahoma Drainage.  We Performed or first Sprinkler Repair in Norman in 1993.  It was in Brookhaven on the West side of Norman.

Recently we had a customer in Oklahoma City who wanted to move his Sprinkler Valves.  They were in a bad place in his flower bed.  He wanted to plant a tree where the valves were located.

We moved 4 Sprinkler Valves about feet out into the yard.  All the Sprinkler Pipes had to be redesigned and installed matching the new location and maintaining full functionality.

 

 

Sprinkler Service Oklahoma City

Posted: December 1, 2025 in sprinkler repair, Sprinkler Repair Service, Sprinkler Service
Tags: , , ,
0

Sprinkler Service Oklahoma City.  Oklahoma Drainage and Sprinkler Repair has provided Expert Sprinkler Repair and Service in Oklahoma City Since 1993.

 

Recently we fixed a broken Sprinkler Pipe under a driveway in Norman.  It was leaking out onto the street every time the sprinkler system ran.   The pipe had to be removed and a new PVC pipe put in its place.

It was located on the west side of Norman in Brookhaven.

Oklahoma Drainage and Sprinkler Repair provide Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

 

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,   Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

We started with the Valves

The Sprinkler Valves were located in the back yard near the pool.  Six valves were located in one place.  They were very tightly connected in one Manifold.  None of the Sprinkler Valves had worked in a long time.  They were Toro Valves that were over 20 years old.  They all had to be replaced.

Surprisingly there was no shut-off valve for the Sprinkler Water.  The water had to be shut off at the Meter so we could install a Manual Shut off valve.  Once installed, the water was turned back on that ran to the house.   The water that ran to the Sprinkler System was shut off with our New Shut Off Valve.

Rainbird Sprinkler Valve

Rainbird Sprinkler Valve

The Sprinkler Valves Were Removed

Now, the 6 valves had to replaced.  The valves that were used were made by Rain Bird.  Before we began, I had to talk to the Customer.  The previous valve design was a bad idea to repeat.

The original Sprinkler Valves were crammed into one large valve box in one very tight manifold.  This is bad because the valves were too close to the fittings.  Simply put, if one valve had to be replaced or worked on in the future, all 6 valves had to be taken out and replaced.   If one valve was bad and 5 worked fine, they all still had to be replaced.

That’s Stupid!

I recommended that an additional Valve Box be installed putting 3 valves in each Valve Box.  This would allow plenty of space between the valve fittings.  If one Sprinkler Valve had to be adjusted or replaced in the future, the other 5 valves need not be disturbed.  Simple Enough!

Check For Leaks

Once the valves were replaced and working, it was time to turn on each Sprinkler Zone, one at a time.  Water was shooting up from the ground in several places in zone 1.  Two broken Sprinkler Pipes and 5 bad Sprinkler Heads in zone 1 had to be fixed and replaced.  We went through each of the 6 zones in similar fashion fixing lots of leaks and replacing bad sprinkler heads.

The Sprinkler Repair Cost About Half of the Cost of Completely New System.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

Sprinkler Head Adjustment is a service provided by Oklahoma Drainage and Sprinkler Repair.  We have adjusted sprinkler heads since 1993.

Many times, Sprinkler heads get, “Out of Wack.”  Lawn mowers and weed eaters are notorious for this.  Sprinkler heads start spraying water in the wrong place.  It is frustrating to water concrete while plants and grass go without moisture.

Pop-Up Sprinkler Heads

Pop-Up Sprinkler Heads can be adjusted several ways.  How far water goes to the left or right can be increased or decreased.  The distance the water goes can also be increased or decreased.  Finally, how high a sprinkler head pops up can be increased or decreased by installing a taller or shorter head.

Sometimes sprinkler heads spray a reduced distance and don’t perform very well due to water scale.  Minerals in the water can completely clog a Pop-Up.  Usually, the sprinkler nozzle on top of the sprinkler head, need only be replaced without replacing the entire head.

Rotor Sprinkler Heads also can be adjusted to the left or right.  Spray Distance can be increased or decreased as well.

Needs Change

What’s going on in your yard can change.  This calls for Sprinkler Head Adjustment.  Adding or removing a swimming pool changes everything concerning sprinkler heads.  Any number of things can change the necessary sprinkler head coverage.

 

 

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes – Sprinkler Head Adjustment – Sprinkler Valve Replacement

We provide Service for Folks in: Norman, Oklahoma City, Edmond, and Moore.

Central and Western Oklahoma is our Service Area since 1993.  

                                                           (405) 203-9419

Check out Sprinkler System Check-Up

Emergency Sprinkler Repair

Sometimes things go wrong with sprinkler systems.

 

IF YOU NEED HELP IN THE MIDDLE OF THE NIGHT OR ON A WEEKEND WITH YOUR SPRINKLER SYSTEM, GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR.  405 203 9419

IT MAY TAKE A FEW HOURS FOR US TO GET THERE BUT WE WILL COME TO HELP.

 

One Common problem is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

 

Sprinkler Repair Facts

 

Oklahoma Drainage and Sprinkler Repair provides Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

 

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,   Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

We started with the Valves

The Sprinkler Valves were located in the back yard near the pool.  Six valves were located in one place.  They were very tightly connected in one Manifold.  None of the Sprinkler Valves had worked in a long time.  They were Toro Valves that were over 20 years old.  They all had to be replaced.

Surprisingly there was no shut-off valve for the Sprinkler Water.  The water had to be shut off at the Meter so we could install a Manual Shut off valve.  Once installed, the water was turned back on that ran to the house.   The water that ran to the Sprinkler System was shut off with our New Shut Off Valve.

The Sprinkler Valves Were Removed

Now, the 6 valves had to replaced.  The valves that were used were made by Rain Bird.  Before we began, I had to talk to the Customer.  The previous valve design was a bad idea to repeat.

The original Sprinkler Valves were crammed into one large valve box in one very tight manifold.  This is bad because the valves were too close to the fittings.  Simply put, if one valve had to be replaced or worked on in the future, all 6 valves had to be taken out and replaced.   If one valve was bad and 5 worked fine, they all still had to be replaced.

That’s Stupid!

I recommended that an additional Valve Box be installed putting 3 valves in each Valve Box.  This would allow plenty of space between the valve fittings.  If one Sprinkler Valve had to be adjusted or replaced in the future, the other 5 valves need not be disturbed.  Simple Enough!

Check For Leaks

Once the valves were replaced and working, it was time to turn on each Sprinkler Zone, one at a time.  Water was shooting up from the ground in several places in zone 1.  Two broken Sprinkler Pipes and 5 bad Sprinkler Heads in zone 1 had to be fixed and replaced.  We went through each of the 6 zones in similar fashion fixing lots of leaks and replacing bad sprinkler heads.

The Sprinkler Repair Cost About Half of the Cost of Completely New System.

Oklahoma Drainage Installs Drainage Systems,  and provides Expert Sprinkler System Repair.

Our Drainage Systems utilize French Drains, Surface Drains, Channel Drains, and Sump Pumps.  

We Service all of Central Oklahoma including: Norman, Moore, Edmond, Yukon, Mustang, Oklahoma City, Midwest City, Del City, Blanchard, Newcastle, Purcell and Chickasha.

Back-Flow-Valve Service, Sprinkler Repair

Oklahoma Drainage and Sprinkler Repair Provides Service for Back-Flow-Valves and all types of Lawn Sprinkler Repair and Service.  We have provided Expert Service for all of Central and Western Oklahoma Since 1993.

Back-Flow-Valves

There are two types of Back-Flow-Valves.

Above Ground

Above Ground Back-Flow-Valve

Above Ground Back-Flow-Valve.

 

Below Ground Back-Flow-Valve.

Below Ground Back-Flow-Valve

Below Ground Back-Flow-Valve

What is a Back-Flow-Valve?

A Back-Flow-Valve is a part of a Lawn Sprinkler System.  Water passes through it from the water source which can be a Water Meter or a Well Pump.  It forces water to travel in only one direction from the source to the sprinkler system.  It can’t travel backward back to the water source which again is a water meter or well pump.

A Back-Flow-Valve provides protection to the water source from back pressure and chemical contamination from lawn fertilizer.

Most Cities require a Back-Flow-Valve as “Code” for Sprinkler Installation.

Emergency Shut off

Back-Flow-Valves usually have an Emergency Shutoff valve on them that can shut off the water to the lawn sprinkler system but keep the water turned on to the home. Most Back-Flow-Valves have two Emergency Shut off Handles.  Either one will work.  Many times, they are hard to turn, however.

If there is a leak or water is shooting up in the air just turn the valve handle and give us a call.

In ground Back-Flow-Valve

Blue Emergency Shutoff handles for a Back-Flow-Valve.

Norman Sprinkler Checkup is a Central Focus for Oklahoma Drainage.  We Performed or first Sprinkler Repair in Norman in 1993.  It was in Brookhaven on the West side of Norman.

Recently we had a customer in Oklahoma City who wanted to move his Sprinkler Valves.  They were in a bad place in his flower bed.  He wanted to plant a tree where the valves were located.

We moved 4 Sprinkler Valves about feet out into the yard.  All the Sprinkler Pipes had to be redesigned and installed matching the new location and maintaining full functionality.

 

Oklahoma City Sprinkler Service

Posted: November 30, 2025 in sprinkler repair contractor, Sprinkler Repair Service, Sprinkler Service
Tags: , , ,
0

Oklahoma City Sprinkler Service.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR –

Servicing Central and Western Oklahoma since 1993.

Sprinkler Repair – French Drain Installation – Drainage System Installation

This week Oklahoma Drainage and Sprinkler Repair overhauled a flowerbed Sprinkler Zone in a Sprinkler System in East Norman.

The homeowner had an existing Sprinkler System that was in good shape for the most part but had problems with the flowerbed Sprinkler Zone.

It had a Drip Sprinkler Zone installed.  The Drip Sprinkler System was installed correctly but was not practical for the flower bed.

The flowerbed was very sandy and could not retain water very well even with good mulch.  Plus, the surrounding brick walls increased the amount of heat the plants had to endure in the summer.  The Drip Sprinkler Zone could not provide enough water fast enough for the plants.

We provide:

1.  Sprinkler Valve Problems

2.  Sprinkler Wiring Problems

3.  Sprinkler Controller Problems / Sprinkler Clock Problems

4.  Sprinkler Head Problems

5.  Sprinkler Pipe Problems

6.  Sprinkler Coverage Problems

7.  Sprinkler Redesign Problems for new fences or swimming pools.

Sprinkler Repair

is a central focus for Oklahoma Drainage and Sprinkler Repair.  Just like any car or home, a lawn sprinkler system must be updated and maintained.  Typically, people wait till spring to get the kinks worked out of their sprinkler system.

Sprinkler Repair is an ongoing issue for any sprinkler system.  Folks in Central Oklahoma are turning on their Sprinkler Systems and discovering problems.

We fixed several leaks in a Sprinkler System in Edmond.

The sprinkler pipes were leaking in several places.  Each leak had to be cut out and replaced.

The Sprinkler System was fairly new.  It was installed last summer by a Pool Company that also installs cheap sprinkler systems.

All the joints in the sprinkler pipes

were glued together with clear PVC Cement.  That part is OK, but they cut some corners and didn’t use PVC Primer with the glue.  As a result, the joints didn’t bond very well and many of them blew apart this spring when the sprinkler systems were turned on.  (Thus, all the leaks) I suspect we will have to go back several times to fix additional leaks.

We can only warranty the PVC joints that we have replaced.   Cheaper isn’t always better.

Today we did a sprinkler repair in Norman.  The sprinkler system needed a checkup.  We went through each sprinkler zone and identified several different problems.  Zone 2 had a cracked sprinkler pipe in a flower bed.

Next, Zone 4 had a broken sprinkler rotor on the edge of the driveway that had been driven over and broken.

Spraying Rotor Sprinkler Repair

Spraying Rotor Sprinkler Head

Zone 6 and 7 each had a couple of pop-up spray heads that were worn out and would not pop-up.  The diagnosis and the repair took less than two hours.  Now their sprinkler system is running great!

Don’t Wait!

I can tell you this, DON’T WAIT TILL MARCH TO GET YOUR SPRINKLER SYSTEM IN SHAPE.  BY APRIL THERE WILL BE A FLOOD OF PEOPLE TRYING TO GET BROKEN SPRINKLER HEADS FIXED OR NEW SPRINKLER CONTROLLERS INSTALLED OR LEAKING BACK-FLOW VALVES REPLACED.

CONSIDER GETTING YOUR SPRINKLER REPAIR WORK DONE ANY TIME OTHER THAN THE SPRING.  FOR THOSE OF YOU WHO HAVE NO CHOICE AND MUST HAVE WORK DONE IN THE SPRING, SCHEDULE AS EARLY AS YOU CAN.

OUR SPRINKLER REPAIR WORK IS TOP QUALITY AND OUR PRICES ARE FAIR.  IT IS OUR GOAL TO GET TO CUSTOMERS QUICKLY IN MARCH AND APRIL, WHILE MAINTAINING OUR QUALITY OF WORK.

 

Oklahoma Drainage and Sprinkler Repair

can help if you need to re-design your Sprinkler System.  If for example you are adding a swimming pool in your back yard, we can move the Sprinkler Heads and Sprinkler Pipes to fit the new dimensions of your yard.  We can redesign or add-on to sprinkler systems where the homeowners need change.

Maybe you don’t need a large part of your sprinkler system redesigned.  You May just want a few heads moved to new locations.

Whatever your Sprinkler needs may be, Oklahoma Drainage and Sprinkler Repair can help.  Give us a call at : 405 203 9419

 

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?

A lot!!!!

Oklahoma Drainage and Sprinkler Repair provides Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

Sprinkler Repair for us is very clear.  We have been doing it a long time and have become very good at it.  Many times, we get called in to handle tough problems that the initial Sprinkler Company couldn’t handle.

Oklahoma Drainage Installs Drainage Systems,  and provides Expert Sprinkler System Repair.

Our Drainage Systems utilize French Drains, Surface Drains, Channel Drains, and Sump Pumps.  

We Service all of Central Oklahoma including: Norman, Moore, Edmond, Yukon, Mustang, Oklahoma City, Midwest City, Del City, Blanchard, Newcastle, Purcell and Chickasha.

Back-Flow-Valve Service, Sprinkler Repair

Oklahoma Drainage and Sprinkler Repair Provides Service for Back-Flow-Valves and all types of Lawn Sprinkler Repair and Service.  We have provided Expert Service for all of Central and Western Oklahoma Since 1993.

Back-Flow-Valves

There are two types of Back-Flow-Valves.

Above Ground

Above Ground Back-Flow-Valve

Above Ground Back-Flow-Valve.

 

Below Ground Back-Flow-Valve.

What is a Back-Flow-Valve?

A Back-Flow-Valve is a part of a Lawn Sprinkler System.  Water passes through it from the water source which can be a Water Meter or a Well Pump.  It forces water to travel in only one direction from the source to the sprinkler system.  It can’t travel backward back to the water source which again is a water meter or well pump.

A Back-Flow-Valve provides protection to the water source from back pressure and chemical contamination from lawn fertilizer.

Most Cities require a Back-Flow-Valve as “Code” for Sprinkler Installation.

Emergency Shut off

Back-Flow-Valves usually have an Emergency Shutoff valve on them that can shut off the water to the lawn sprinkler system but keep the water turned on to the home. Most Back-Flow-Valves have two Emergency Shut off Handles.  Either one will work.  Many times, they are hard to turn, however.

If there is a leak or water is shooting up in the air just turn the valve handle and give us a call.

In ground Back-Flow-Valve

Blue Emergency Shutoff handles for a Back-Flow-Valve.

Norman Sprinkler Checkup is a Central Focus for Oklahoma Drainage.  We Performed or first Sprinkler Repair in Norman in 1993.  It was in Brookhaven on the West side of Norman.

Recently we had a customer in Oklahoma City who wanted to move his Sprinkler Valves.  They were in a bad place in his flower bed.  He wanted to plant a tree where the valves were located.

We moved 4 Sprinkler Valves about feet out into the yard.  All the Sprinkler Pipes had to be redesigned and installed matching the new location and maintaining full functionality.

 

Older Entries
Newer Entries