Posts Tagged ‘Blanchard French Drain’

Blanchard French Drain.  Oklahoma Drainage and Sprinkler Repair has provided Expert Service and Installation in Blanchard since 1993.

Many times, people believe that a French Drain has a Grate on the Top.  It does not.

The Picture above is a Surface Drain.

French Drain – A French Drain is a perforated pipe that is basically full of slits or holes.  A trench is dug across the problem drainage area.   A Semi-permeable liner is placed in the trench which lets in water but not dirt. The dirt from the trench is hauled away.   The French Drainpipe has a Neo-Preen Soc around it witch also lets in water but keeps the dirt out.

The perforated pipe is placed in the trench.  The Drainage trench is dug deep enough so that the perforated French Drainpipe is several inches below ground level when placed in the trench.  Next gravel or some type of crushed stone is placed on top and around the French Drain perforated pipe until the trench is full.

 

 

 

A basic French Drain consists of a Perforated Drainpipe in the bottom of a trench. The French Drain Trench runs through a Problem Drainage Area that needs to be drained.   The French Drainpipe is perforated (Full of Small Holes) and has Neo-Prene Soc around the pipe.  This soc helps prevent debris from clogging the French Drainpipe.

 

The dirt that was taken out to from the trench is hauled away. It is replaced by some type of small stone or gravel depending on what is desired or available.

Gravel or Crushed Limestone

I prefer crushed 1 inch limestone. It is the most economical option in my area. Pea Gravel or some other type of small stone can work just as well. The limestone or gravel is placed in the trench on top of the perforated Drainpipe and filled all the way to the surface (ground level).

In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drainpipe or the Gravel are installed. This helps maintain the integrity of the trench over time. It also increases the cost of the French Drain and the amount of time to install it. It is a good practice to always install a Trench Liner.

 

French Drain is designed to handle a large volume of water and cover a large area. The Drain is anyplace the trench goes. It has many applications and can be used in many situations. It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Down-Spouts connected to it.

The main downfall

of a French Drain is that they, for the most part isn’t very pretty. They don’t look very nice in a yard once they are completed.

Depending on the area the French Drain is installed and the type of grass around the French Drain, will dictate whether grass grows over the limestone. Grass can grow up and through the gravel in the French Drain over time eventually covering the gravel. This is Ok. It won’t have a measurable effect on the performance of the drain.

DONT COVER THE GRAVEL IN THE FRENCH DRAIN WITH DIRT. THE FRENCH DRAIN WON’T WORK IF THE TRENCH IS CLOGGED WITH DIRT. DON’T EVEN INSTALL IT IF YOU ARE GOING TO COVER IT UP WITH DIRT.

DECORATIVE STONE CAN BE USED TO COVER A FRENCH DRAIN AND THEY LOOK GREAT AND LAST A LIFETIME.

WHERE WE HAVE WORKED!

In 1993 we had no website.  I stuck little signs on the side of the road as advertisement.  I got my first Drain Installation work in March of 1993 in Norman.  It was in Brookhaven North of Robinson Street on the West side of I 35.

Over the years Oklahoma Drainage and Sprinkler Repair has installed all types of Drainage Systems in almost Every town in Central and Western Oklahoma.

The majority of our customers live in Oklahoma City, Norman, Edmond, Yukon, Mustang, Moore, Midwest City, Del City, Blanchard, New Castle, Yukon and Choctaw.

Oklahoma Drainage and Sprinkler Repair hasn’t been limited to those areas, however.  We have also installed French Drains, Surface Drains, Channel Drains, and Sump Pumps in many other cities.

Working Drainage Systems Installed by Oklahoma Drainage also reside in: Lawton, Duncan, Ardmore, Chickasha, Shawnee, Enid, Weatherford, Elk City, El reno and many other places.

If you live in any of these Cities or towns, we have installed a French Drain, Surface Drain, Channel Drain, or Sump Pump within 5 miles of your home.

Here is a description of other recent work.

A little bit North of Downtown Oklahoma City, Oklahoma Drainage installed a 6-inch French Drain between two businesses which were less than three feet apart.  The French Drain went between a Law Firm and a Tire shop.  Water was leaking through the walls of both businesses.  Gutters between the two establishments were dumping a huge amount of water.  We installed a 6-inch French Drain between the gutters.

It took a long time to get the dirt out of the trench for the French Drain.  It was a very tight fit.  We had to use a little red wagon to haul out the dirt for the French Drain and haul back in the crushed limestone for the French Drain.  It looked a little silly, but it was the only thing we could find that was narrow enough to fit between the buildings.  A French Drain that normally would take 1 day to install took three.


Oklahoma Drainage and Sprinkler Repair has been installing French Drains in Newcastle since 1993.  We have helped over 4000 customers in Central and Western Oklahoma.
We install: French Drains, Surface Drains, Channel Drains and Sump PumpsSprinkler Repair and Sod Installation are Also Available.

Oklahoma Drainage and Sprinkler Repair — Installing – French DrainsSurface DrainsChannel DrainsSump Pumps

Providing Expert Sprinkler Repair Broken Sprinkler PipesSprinkler Head AdjustmentSprinkler Valve Replacement

Servicing all of Central and Western Oklahoma since 1993.

Oklahoma Drainage and Sprinkler Repair – French Drain Installation, Drainage System Design, Expert Lawn Sprinkler Repair, Drain Repair 

Recently Oklahoma Drainage and Sprinkler Repair installed a large 6-inch French Drain in Edmond.  The customer had water running under his back porch step and into his basement.

We did a Free Drainage Diagnostic and Estimate.  The French Drain design that we proposed would intercept the surface water and subsurface water that was flowing under the steps.

The French Drain design called for a 6-inch French Drain to be installed above and several feet away from the steps.  It would run around the house parallel to the foundation and about 5 feet to the East.  The French Drain would run past the steps to a point where water must cross the French Drain or run up hill to the steps which in this case was not possible.

 Once past the steps, the French Drain would transition to Solid 6-inch Drainpipe and continue on around the house to the Pop-Up Emitter downhill in the side yard.  Along the way we attached several Gutter Down Spouts into the French Drain.

 

Channel Drain Installation require a high level of Experience and attention to detail.

Curb Outlet for French Drain in Edmond

Curb Outlet for French Drain in Edmond

French Drain Installation

Oklahoma Drainage and Sprinkler Repair has been diagnosing and solving Drainage Problems since 1993.  Water has the ability to get into places around your home where you really don’t want it to be.  Some drainage problems are easy to solve.

Typically water enters the problem drainage area one way from one source.  The really tricky drainage problems occur when water enters the problem drainage area from multiple directions and from multiple sources.  Sometimes a secondary water source can’t be seen or identified until the primary water problem source is eliminated.

An example of this occurs when water is running into a problem area in an obvious way over the ground where you can see it.

Simple enough.

A drainage system is installed with a surface drain as the “intake” with drainage pipe running to an exit point.  Initially the water drains away, and everything looks great.

The next day water is back and is all around the surface drain, but below the edge and it hasn’t rained at all, so no additional water ran over the surface of the ground to flood the area.

The primary water source was solved, ( The surface water run off ) but the secondary water source was not.  Which was sub-surface water, (ground water) running into the area.  A surface drain can’t drain “ground water.”  A French Drain should have initially been installed instead of a Surface Drain.  A French Drain can drain both Surface Water and Ground Water.

 

A French Drain Can Handle Standing Water

 

Oklahoma Drainage and Sprinkler Repair

Services all of Central Oklahoma including Norman, Moore, Edmond, Yukon, Mustang, Oklahoma City, Midwest City, Del City, Blanchard, Newcastle, Purcell and Chickasha.

 

Keep water off your driveway with a channel drain

 Standing water comes from many sources.  It causes damage to sidewalks, driveways, and foundations not to mention plants, trees, and grass. 

Does the side of your house flood because your neighbor doesn’t have gutters. Is your sidewalk turning into a moat after a heavy rain? Worst of all, is water seeping into your foundation and duct work after a thunderstorm? 

These are just a few of the Drainage Problems that Oklahoma Drainage and Sprinkler Repair can help with.  We can design a Drainage System to fit your specific needs. 

We install many types of Drains to solve many types of problems.   

French Drains, Surface Drains, Channel Drains, Basement Drains, Trench Drains, Basin Drains, and Sump Pumps are utilized.

 

 

 

Just what is a “French Drain?”  Many times, people incorrectly

use the phrase, “French Drain,” to apply to many different types of Drains that could be used in a Drainage System.  The term is widely used and many times incorrectly connected to “Surface Drains,” or “Channel Drains.”

A Surface Drain has a grate that sits on top of a basin.  The basin is underground.  A Drainpipe is connected underground to an outlet on the Drain BasinStormwater Drains through the grate into the Drain Basin.  Once in the Drain Basin, through a Drainpipe.  The Stormwater continues downhill in an underground Drainpipe to an exit point.

THIS IS NOT A FRENCH DRAIN!

A Surface Drain may come in many different shapes or sizes.  The Drain Grate may be round or square.  Here is a picture of a common Surface Drain.

Surface Drain with a Black Grate

Cutting the Curb

Cutting the Curb for a French Drain Outlet

A Channel Drain is a type of Surface Drain, and many times is installed in

Channel Drain
 

4 Inch Drain Pipe Ready to be covered with dirt in Norman.
4 Inch Drainpipe Ready to be covered with dirt in Norman.

 

 

French Drain for Flood Control.  Sometimes French Drains are installed to control flooding.  Many times, areas can flood that have drains already installed.  As a general rule, a French Drain can take water into the drainpipe faster than a Surface Drain if installed correctly.

French Drain

Oklahoma Drainage  — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps

If you have water causing damage to your home or business, we can help!  Oklahoma Drainage has been solving drainage and water problems since 1993.  If you have water standing in your yard or it’s leaking into your AC ducts, we can help.

 

Servicing all of Central and Western Oklahoma since 1993.

French Drain Installation

Oklahoma Drainage and Sprinkler Repair has been diagnosing and solving Drainage Problems since 1993.  Water has the ability to get into places around your home where you really don’t want it to be.  Some drainage problems are easy to solve.

Typically, water enters the problem drainage area one way from one source.  The really tricky drainage problems occur when water enters the problem drainage area from multiple directions and from multiple sources.  Sometimes a secondary water source can’t be seen or identified until the primary water problem source is eliminated.

An example of this occurs when water is running into a problem area, in an obvious way, over the ground where you can see it.

Simple enough.

A drainage system is installed with a surface drain as the “intake” with drainage pipe running to an exit point.  Initially the water drains away and everything looks great.  The next day water is back and is all around the surface drain, but below the edge and it hasn’t rained at all, so no additional water ran over the surface of the ground to flood the area.  The primary water source was solved, ( The surface water run off ) but the secondary water source was not.  Which was sub-surface water, (ground water) running into the area.

Surface Drain Limitations

A surface drain can’t drain “ground water.”  A French Drain should have initially been installed instead of a Surface Drain.  A French Drain can drain both Surface Water and Ground Water All Drainage Systems and French Drains as well need a place to take the water to.  This is called an Exit Point.  We use two types of Exits.  The first is a curb outlet.  We cut the curb with a concrete saw and install a rectangular curb outlet set in acrylic concrete.

new curb outlet

Curb outlet with more than 6 inches of fall

A rectangular outlet is superior to a round one.  Air travels back up the pipe through the top two corners to allow a more continuous water flow.  If you have ever poured liquid out of a 2 liter bottle turning it completely upside down, you will see that it drains but not very well.

decorative french drain

Decorative French Drain Running Across a Flower Bed

Oklahoma Drainage installs a variety of other types of Drains.  Our Drainage Systems may utilize: French Drains, Surface Drains, Channel Drains, Trench Drains, Basin Drains, and Sump Pumps.  In the past 31 years, we have installed French Drains to keep water away from home and business foundations,

Surface Drains to keep water away from sidewalks and driveways, Trench Drains, and French Drains to keep standing water out of flowerbeds and yards, and Sump Pumps to remove water from basements and outdoor low-lying areas.

Drainage Problems

Wow, Some Drainage Problems are tougher than others.  Had a customer in Chickasha with an unusual Drainage Problem.  She had a new Driveway installed.  The Cement work was nice enough but they left out one major consideration when installing the new Driveway.  Even after a small rain the water would run right down the driveway, under the Garage Door and directly into the Garage.

Church drain dig

Digging a Large Drainage System for a Church

This was a bad problem that was about to get worse.  The first big rain came and everything was magnified.  The Rushing water took out the garage door and the back wall of the garage.  Yikes!!

Hmm, What to do?  The company that installed the Driveway was nowhere to be found.  No surprise.

The water volume was huge, and the customer had no means to redo the driveway which was substantial.

WHERE WE HAVE WORKED!

In 1993 we had no website.  I stuck little signs on the side of the road as advertisement.  I got my first Drain Installation work in March of 1993 in Norman.  It was in Brookhaven North of Robinson Street on the West side of I 35.

Over the years Oklahoma Drainage and Sprinkler Repair has installed all types of Drainage Systems in almost Every town in Central and Western Oklahoma.

The majority of our customers live in Oklahoma City, Norman, Edmond, Yukon, Mustang, Moore, Midwest City, Del City, Blanchard, New Castle, Yukon and Choctaw.

Oklahoma Drainage and Sprinkler Repair hasn’t been limited to those areas, however.  We have also installed French Drains, Surface Drains, Channel Drains, and Sump Pumps in many other cities.

Working Drainage Systems Installed by Oklahoma Drainage also reside in: Lawton, Duncan, Ardmore, Chickasha, Shawnee, Enid, Weatherford, Elk City, El reno and many other places.

If you live in any of these Cities or towns, we have installed a French Drain, Surface Drain, Channel Drain, or Sump Pump within 5 miles of your home.

Here is a description of other recent work.

A little bit North of Downtown Oklahoma City, Oklahoma Drainage installed a 6-inch French Drain between two businesses which were less than three feet apart.  The French Drain went between a Law Firm and a Tire shop.  Water was leaking through the walls of both businesses.  Gutters between the two establishments were dumping a huge amount of water.  We installed a 6-inch French Drain between the gutters.

It took a long time to get the dirt out of the trench for the French Drain.  It was a very tight fit.  We had to use a little red wagon to haul out the dirt for the French Drain and haul back in the crushed limestone for the French Drain.  It looked a little silly, but it was the only thing we could find that was narrow enough to fit between the buildings.  A French Drain that normally would take 1 day to install took three.

Sprinkler Repair Facts

 

Oklahoma Drainage and Sprinkler Repair provides Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

Emergency Sprinkler Repair

Sometimes things go wrong with sprinkler systems.

 

IF YOU NEED HELP IN THE MIDDLE OF THE NIGHT OR ON A WEEKEND WITH YOUR SPRINKLER SYSTEM, GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR.  405 203 9419

IT MAY TAKE A FEW HOURS FOR US TO GET THERE BUT WE WILL COME TO HELP.

 

One Common problem is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

 

Inside the valve box is a plastic handle that can turn off the water to the sprinkler system.  It can be blue or red or grey in color.

Many times, the valve box will be full of dirt, and you can’t turn or even see the handle until some of the dirt has been dug out by hand.

 

Water might be shooting up in the air somewhere on your property.  This can be caused by a broken sprinkler pipe or sprinkler valve.

SHUT OFF THE SPRINKLER WATER IF YOU CAN AND GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR. SERVICING ALL OF CENTRAL AND WESTERN OKLAHOMA.

405 203 9419

Servicing Oklahoma City, Norman, Edmond and all of Central and Western Oklahoma

 

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,     Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

We started with the Valves

The Sprinkler Valves were located in the back yard near the pool.  Six valves were located in one place.  They were very tightly connected in one Manifold.  None of the Sprinkler Valves had worked in a long time.  They were Toro Valves that were over 20 years old.  They all had to be replaced.

Surprisingly there was no shut-off valve for the Sprinkler Water.  The water had to be shut off at the Meter so we could install a Manual Shut off valve.  Once installed, the water was turned back on that ran to the house.   The water that ran to the Sprinkler System was shut off with our New Shut Off Valve.

Rainbird Sprinkler Valve

Rainbird Sprinkler Valve

The Sprinkler Valves Were Removed

Now, the 6 valves had to replaced.  The valves that were used were made by Rain Bird.  Before we began, I had to talk to the Customer.  The previous valve design was a bad idea to repeat.

The original Sprinkler Valves were crammed into one large valve box in one very tight manifold.  This is bad because the valves were too close to the fittings.  Simply put, if one valve had to be replaced or worked on in the future, all 6 valves had to be taken out and replaced.   If one valve was bad and 5 worked fine, they all still had to be replaced.

That’s Stupid!

I recommended that an additional Valve Box be installed putting 3 valves in each Valve Box.  This would allow plenty of space between the valve fittings.  If one Sprinkler Valve had to be adjusted or replaced in the future, the other 5 valves need not be disturbed.  Simple Enough!

Check For Leaks

Once the valves were replaced and working, it was time to turn on each Sprinkler Zone, one at a time.  Water was shooting up from the ground in several places in zone 1.  Two broken Sprinkler Pipes and 5 bad Sprinkler Heads in zone 1 had to be fixed and replaced.  We went through each of the 6 zones in similar fashion fixing lots of leaks and replacing bad sprinkler heads.

The Sprinkler Repair Cost About Half of the Cost of Completely New System.

Rotor and Pop-Up Sprinkler Heads

Rotor and Pop-Up Sprinkler Heads

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

Sprinkler Head Adjustment is a service provided by Oklahoma Drainage and Sprinkler Repair.  We have adjusted sprinkler heads since 1993.

Many times, Sprinkler heads get, “Out of Wack.”  Lawn mowers and weed eaters are notorious for this.  Sprinkler heads start spraying water in the wrong place.  It is frustrating to water concrete while plants and grass go without moisture.

Pop-Up Sprinkler Heads

Pop-Up Sprinkler Heads can be adjusted several ways.  How far water goes to the left or right can be increased or decreased.  The distance the water goes can also be increased or decreased.  Finally, how high a sprinkler head pops up can be increased or decreased by installing a taller or shorter head.

Sometimes sprinkler heads spray a reduced distance and don’t perform very well due to water scale.  Minerals in the water can completely clog a Pop-Up.  Usually, the sprinkler nozzle on top of the sprinkler head, need only be replaced without replacing the entire head.

Rotor Sprinkler Heads also can be adjusted to the left or right.  Spray Distance can be increased or decreased as well.

Needs Change

What’s going on in your yard can change.  This calls for Sprinkler Head Adjustment.  Adding or removing a swimming pool changes everything concerning sprinkler heads.  Any number of things can change the necessary sprinkler head coverage.

 

 

Oklahoma Drainage and Sprinkler Repair — Installing – French DrainsSurface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler RepairBroken Sprinkler Pipes Sprinkler Head AdjustmentSprinkler Valve Replacement

We provide Service for Folks in: Norman, Oklahoma City, Edmond, and Moore.

Central and Western Oklahoma is our Service Area since 1993.  

                                                           (405) 203-9419

Check out Sprinkler System Check-Up

 

Decorative French Drain and Channel Drain

French Drain Blanchard, Installation, Information, Norman, Moore, Edmond, Blanchard

Servicing Central and Western Oklahoma Since 1993

Oklahoma Drainage recently diagnosed a Drainage Problem in South Oklahoma City.  The Home owner had a sump Pump in their basement that was fed from a French Drain outside the Basement Wall.  The Drain was 14 feet down along the Stem wall of the house.

The French Drain Pipe was cheap and had collapsed.  We brought in a Mini Excavator and dug up the pipe and replaced it with Durable ADS 4 inch perf/soc French Drain pipe.  In the end, we were able to dig up the pipe and replace it.

French Drain Design

French Drain Design must take into account many variables.  One consideration for a French Drain that many times is missed, is the type of soil.  French Drain Design must take into account the type of soil that the French Drain runs through.  If the soil is “Tight or made up of Clay, A French Drain Liner may not be necessary.  The Gravel or Limestone that is used to fill the French Drain trench may be all that is needed to maintain the integrity of the trench over time.   This means that dirt will not mix in with the French Drain Gravel and clog it up over time.

This is not the case however if your soil is sandy or loose.  A Trench Liner should be used to prevent this type of soil from moving into the gravel of the French Drain.  Trench Liners are relatively inexpensive and are not hard to install.  If you are not sure what to do then install the Trench Liner in the French Drain.

What Does a  Good Drainage System Have?

A good Drainage System has a point where water enters the System.  This is usually through a French Drain, Surface Drain, or a Gutter Down Spout that is connected into a Drainpipe.

Water will run through either Perforated French Drainpipe or Solid Drainpipe depending on the Drainage System Design.  Water will flow down hill to an Exit Point where the water will be released out of the Drainage System.  This is a done through a Pop-Up Emitter or a Curb Fitting.

Drainage Systems can be made up of one drain or a combination of many drains.  They can be very complex.   Complex Drainage Problems may require a combination of several different types of drains all inter-connected and working together.

Other times the drainage problem may be simple and straight-forward requiring only one drain or several of the same type of drain connected together.

An example of a complex drainage system would be:  A French Drain in the back yard connected to a Surface Drain near a flower bed connected to several gutter downspouts, which are connected to a Channel Drain going across a driveway, which is connected to additional Surface Drain in the front yard, which runs to a Curb Fitting that lets all the water drain out on to the street.

A simple Drainage System might consist of a Surface Drain that is connected to a second Surface Drain which runs to a Pop-up Emitter which lets water drain over the curb and into the street.

6 Inch French Drain Installation

Today we installed a 6 Inch French Drain at an apartment complex near Lake Heffner.  The French Drain started in the back yard of one unit.  The Drainpipe went under the fence and into the adjoining unit’s back yard.  The French Drain then looped around their patio and out under their fence to the west.  To get the 6-inch Drainpipe to the correct Exit Point, we had to cut out 30 feet of sidewalk and run the French Drainpipe under the sidewalk.

Next, we replaced the sidewalk with new concrete.  Finally, we dug a drainage ditch across the front yard to the parking lot.  We covered the Drainpipe with sod that we carefully removed when digging the trench.

We installed a 6-inch pop up emitter At the edge of the parking lot.   Seven Gutters were connected directly into the Drainage System along the way.

This particular Drainage System was made up of 55 Feet of 6-inch French Drain, 78 Feet of Solid ADS Solid Drainpipe, Seven Gutter Connections, and one 6-inch Pop-Up Emitter.

Oklahoma Drainage — We install French Drains, Channel Drains, Surface Drains, Sump Pumps and Sod.

 

If You live in Oklahoma City and water damaging your foundation, We can install a French Drain for you.

 

If you live in Norman and have water standing on your driveway, We can install a Channel Drain for you.

 

If you live in Edmond and have water flooding your basement, We can install a Sump Pump for you.

 

If you live in Moore and have water washing out your flower bed mulch, We can install a Surface Drain for you.

 

If you live in Yukon and need grass to grow we can install Sod too!

 

Servicing All Of Central And Western Oklahoma Since 1993.

 

Oklahoma Drainage

This Year we are Celebrating our 30th Year in business and surpassing our 4000th customer later this year!

We have provided service in over 40 cities and towns in Oklahoma!

 

 

Details are important for a Drainage System Installation, Including French Drains, Channel Drains, Surface Drains, and Sump Pumps.

Below are some of those details.Moore Oklahoma French Drain

 

French Drain Design must take into account many variables.  One consideration for a French Drain that many times is missed, is the type of soil.  French Drain Design must take into account the type of soil that the French Drain runs through.  If the soil is “Tight or made up of Clay, A French Drain Liner may not be necessary.  The Gravel or Limestone that is used to fill the French Drain trench may be all that is needed to maintain the integrity of the trench over time.   This means that dirt will not mix in with the French Drain Gravel and clog it up over time.  This is not the case however if your soil is sandy or loose.  A Trench Liner should be used to prevent this type of soil from moving into the gravel of the French Drain.  Trench Liners are relatively inexpensive and are not hard to install.  If you are not sure what to do then install the Trench Liner in the French Drain.

French Drain Installation

French drain Installation
with trench liner and pipe filter,                          Drain Definitions 

A good Drainage System has a point where water enters the System.  This is usually through a French Drain, Surface Drain, or a Gutter Down Spout that is connected into a Drain Pipe.   Water will run through either Perforated French Drain Pipe or Solid Drain Pipe depending on the Drainage System Design.  Water will flow down hill to an Exit Point where the water will be released out of the Drainage System.  This is a done through a Pop-Up Emitter or a Curb Fitting.

Drainage Systems can be made up of one drain or a combination of many drains.  Drainage  problems can be very complex.   Complex Drainage Problems may require a combination of several different types of drains all inter-connected and working together.  Other times the drainage problem may be simple and straight-forward requiring only one drain or several of the same type of drain connected together.

An example of a complex drainage system would be:  A French Drain in the back yard connected to a Surface Drain near a flower bed connected to several gutter downspouts, which are connected to a Channel Drain going across a driveway, which is connected to additional Surface Drain in the front yard, which runs to a Curb Fitting that lets all the water drain out on to the street.

A simple Drainage System might consist of a Surface Drain that is connected to a second Surface Drain which runs to a Pop-up Emitter which lets water drain over the curb and into the street.

Today we installed a 6 Inch French Drain at an apartment complex near Lake Heffner.  The French Drain started in the back yard of one unit.  The Drain Pipe went under the fence and into the adjoining unit’s back yard.  The French Drain then looped around their patio and out under their fence to the west.  To get the 6 inch Drain Pipe to the correct Exit Point, we had to cut out 30 feet of sidewalk and run the French Drain Pipe under the sidewalk.  Next, we replaced the sidewalk with new concrete.  Finally, we dug a drainage ditch across the front yard to the parking lot.  We covered the Drain Pipe with sod that we carefully removed when digging the trench.  At the edge of the parking lot a 6 inch Pop-Up Emitter was installed to release the Storm water.  Seven Gutters were connected directly into the Drainage System along the way.

This particular Drainage System was made up of 55 Feet of 6 inch French Drain, 78 Feet of Solid ADS Solid Drain Pipe, Seven Gutter Connections, and one 6 inch Pop-Up Emitter.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

Oklahoma Drainage and Sprinkler Repair — Installing – French DrainsSurface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes Sprinkler Head AdjustmentSprinkler Valve Replacement

We provide Service for Folks in: Norman, Oklahoma City, Edmond, and Moore.

Central and Western Oklahoma is our Service Area since 1993.  

                                                           (405) 203-9419