Posts Tagged ‘Lawton Sprinkler Repair’

Lawton Sprinkler Repair

Posted: March 23, 2025 in Emergency Sprinkler Repair, Lawton Oklahoma Sprinkler Repair, Lawton Sprinkler Repair
Tags:
1

Lawton Sprinkler Repair is a Service provided by Oklahoma Drainage and Sprinkler Repair.  We have serviced and repaired sprinkler systems since 1993.

Emergency Sprinkler Repair

Sometimes things go wrong with sprinkler systems.

 

IF YOU NEED HELP IN THE MIDDLE OF THE NIGHT OR ON A WEEKEND WITH YOUR SPRINKLER SYSTEM, GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR.  405 203 9419

IT MAY TAKE A FEW HOURS FOR US TO GET THERE BUT WE WILL COME TO HELP.

 

One Common problem is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

 

Inside the valve box is a plastic handle that can turn off the water to the sprinkler system.  It can be blue or red or grey in color.

Many times, the valve box will be full of dirt, and you can’t turn or even see the handle until some of the dirt has been dug out by hand.

 

Water might be shooting up in the air somewhere on your property.  This can be caused by a broken sprinkler pipe or sprinkler valve.

SHUT OFF THE SPRINKLER WATER IF YOU CAN AND GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR. SERVICING ALL OF CENTRAL AND WESTERN OKLAHOMA.

405 203 9419

Servicing Oklahoma City, Norman, Edmond and all of Central and Western Oklahoma

Recently in Lawton

Many times, Sprinkler heads get, “Out of Wack.”  Lawn mowers and weed eaters are notorious for this.  Sprinkler heads start spraying water in the wrong place.  It is frustrating to water concrete while plants and grass go without moisture.

Recently we had a customer who had sprinkler heads that were spraying out into the street more than they were hitting her yard.

The problem sprinkler head was out of adjustment.  The Rotor Sprinkler Head was turning too far to the right as it turned.  Water was spraying across the road and into the neighbor’s yard.

The Sprinkler Head Adjustment only took a few minutes.  Our customer then requested that we check the entire sprinkler system.  We started at Zone one and carefully put each zone through its Pases.

Sprinkler Controller Help

Sprinkler Controller

Moore Sprinkler Repair

Sprinkler Controller Programming is sometimes difficult.

We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

The Mistake

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,   Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

 

Sprinkler Valve Replacement

Moore Sprinkler Repair

We rebuilt a Sprinkler System that hadn’t worked in years.  This took place in West Yukon.

We started with the Valves

The Sprinkler Valves were located in the back yard near the pool.  Six valves were located in one place.  They were very tightly connected in one Manifold.  None of the Sprinkler Valves had worked in a long time.  They were Toro Valves that were over 20 years old.  They all had to be replaced.

Surprisingly there was no shut-off valve for the Sprinkler Water.  The water had to be shut off at the Meter so we could install a Manual Shut off valve.  Once installed, the water was turned back on that ran to the house.   The water that ran to the Sprinkler System was shut off with our New Shut Off Valve.

Rainbird Sprinkler Valve

Rainbird Sprinkler Valve

The Sprinkler Valves Were Removed

Now, the 6 valves had to replaced.  The valves that were used were made by Rain Bird.  Before we began, I had to talk to the Customer.  The previous valve design was a bad idea to repeat.

The original Sprinkler Valves were crammed into one large valve box in one very tight manifold.  This is bad because the valves were too close to the fittings.  Simply put, if one valve had to be replaced or worked on in the future, all 6 valves had to be taken out and replaced.   If one valve was bad and 5 worked fine, they all still had to be replaced.

That’s Stupid!

I recommended that an additional Valve Box be installed putting 3 valves in each Valve Box.  This would allow plenty of space between the valve fittings.  If one Sprinkler Valve had to be adjusted or replaced in the future, the other 5 valves need not be disturbed.  Simple Enough!

Check For Leaks

Once the valves were replaced and working, it was time to turn on each Sprinkler Zone, one at a time.  Water was shooting up from the ground in several places in zone 1.  Two broken Sprinkler Pipes and 5 bad Sprinkler Heads in zone 1 had to be fixed and replaced.  We went through each of the 6 zones in similar fashion fixing lots of leaks and replacing bad sprinkler heads.

The Sprinkler Repair Cost About Half of the Cost of Completely New System.

Rotor and Pop-Up Sprinkler Heads

Rotor and Pop-Up Sprinkler Heads

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provides Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang Lawton too!

Sprinkler Head Installation

Lawton Oklahoma Sprinkler Repair

Lawton Oklahoma French Drain, Sprinkler Repair

Posted: February 3, 2020 in Drain Installation, Drain Repair, french drain, French Drain Repair, Lawton Oklahoma French Drain, Sprinkler Checkup, sprinkler repair, Sprinkler Repair Lawton Oklahoma
Tags: , , ,
14

Lawton Oklahoma French Drain

 

 

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes – Sprinkler Head Adjustment – Sprinkler Valve Replacement

Servicing all of Central and Western Oklahoma since 1993.

FRENCH DRAIN IN EDMOND OKLAHOMA, 

Oklahoma Drainage and Sprinkler Repair – French Drain Installation, Drainage System Design, Expert Lawn Sprinkler Repair, Drain Repair 

channel drain driveway

Channel Drain set in Driveway

Recently Oklahoma Drainage and Sprinkler Repair installed a large 6 inch French Drain in Edmond.  The customer had water running under his back porch step and into his basement.

We did a Free Drainage Diagnostic and Estimate.

The French Drain design that we proposed would intercept the surface water and subsurface water that was flowing under the steps.

The design called for a 6-inch French Drain to be installed above and several feet away from the steps.  It would run around the house parallel to the foundation and about 5 feet to the East.

The French Drain would run past the steps to a point where water must cross the French Drain or run up hill to the steps which in this case was not possible.

Once past the steps, the French Drain would transition to Solid 6-inch Drainpipe and continue on around the house to the Pop-Up Emitter downhill in the side yard.  Along the way we attached several Gutter Down Spouts into the French Drain.

 

Curb Outlet for French Drain in Edmond

Curb Outlet for French Drain in Edmond

French Drain Installation

Oklahoma Drainage and Sprinkler Repair has been diagnosing and solving Drainage Problems since 1993.  Water has the ability to get into places around your home where you really don’t want it to be.  Some drainage problems are easy to solve.  Typically water enters the problem drainage area one way from one source.  The really tricky drainage problems occur when water enters the problem drainage area from multiple directions and from multiple sources.  Sometimes a secondary water source can’t be seen or identified until the primary water problem source is eliminated.

An example of this occurs when water is running into a problem area in an obvious way over the ground where you can see it.

Simple enough.

A drainage system is installed with a surface drain as the “intake” with drainage pipe running to an exit point.  Initially the water drains away and everything looks great.  The next day water is back and is all around the surface drain, but below the edge and it hasn’t rained at all, so no additional water ran over the surface of the ground to flood the area.  The primary water source was solved, ( The surface water run off ) but the secondary water source was not.  Which was sub-surface water, (ground water) running into the area.  A surface drain can’t drain “ground water.”  A French Drain should have initially been installed instead of a Surface Drain.  A French Drain can drain both Surface Water and Ground Water.

 

A French Drain Can Handle Standing Water

 FRENCH DRAIN IN EDMOND OKLAHOMA, DRAINAGE CONTRACTOR

Oklahoma Drainage and Sprinkler Repair Recently  installed a large 6 inch French Drain in Edmond.  The customer had water running under his back porch step and into his basement.  We did a Free Drainage Diagnostic and Estimate.  The French Drain design that we proposed would intercept the surface water and subsurface water that was flowing under the steps.  The French Drain design called for a 6 inch French Drain to be installed above and several feet away from the steps.  It would run around the house parallel to the foundation and about 5 feet to the East.  The French Drain would run past the steps to a point where water must cross the French Drain or run up hill to the steps which in this case was not possible.  Once past the steps, the French Drain would transition to Solid 6 inch Drain Pipe and continue on around the house to the Pop-Up Emitter down hill in the side yard.  Along the way we attached several Gutter Down Spouts into the French Drain.

 

A  French Drain is completely different from a Surface Drain.

A basic French Drain consists of a Perforated Drainpipe in the bottom of a trench.

A  Trench Liner is sometimes used depending on the Drainage System Design and the type of soil.

The Drainpipe should have a neoprene sock around the Perforated Drainpipe.   This is to ensure that the Drainpipe does not become clogged.

A trench is dug that is slightly wider than the French Drain Pipe that is being used.

There are several sizes of French Drain Pipe.   Three Inch, Four Inch, and Six Inch are the most common sizes of French drainpipe.

The dirt that is taken out to make the trench is hauled away.

It is replaced by some type of small stone or gravel depending on what is desired or available.  I prefer crushed 1 inch lime stone.  It is the most economical option in my area.  Pea Gravel or some other type of small stone can work just as well.    The lime-stone or gravel is placed in the trench on top of the perforated Drainpipe and filled all the way to the surface (ground level).

A French Drain is designed to handle a large volume of water and cover a large area. The Drain is anyplace the trench goes. It has many applications and can be used in many situations.  It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Down-Spouts connected to it.

Oklahoma Drainage and Sprinkler Repair Services all of Central Oklahoma including: Norman, Moore, Edmond, Yukon, Mustang, Oklahoma City, Midwest City, Del City, Blanchard, Newcastle, Purcell and Chickasha.

 

Keep water off your driveway with a channel drain

 Standing water comes from many sources.  It causes damage to  sidewalks, driveways, and foundations not to mention plants, trees, and  grass. 

 

 

 

Just what is a “French Drain?”  Many times people incorrectly

use the phrase, “French Drain,”  to apply to many different types of Drains that could be used in a Drainage System.  The term is widely used and many times incorrectly connected to “Surface Drains,” or “Channel Drains.”

A Surface Drain has a grate that sits on top of a basin.  The basin is underground.  A Drainpipe is connected underground to an outlet on the Drain Basin.  Stormwater Drains through the grate into the Drain Basin.  Once in the Drain Basin, basin through a Drainpipe.  The Stormwater continues downhill in an underground Drainpipe to an exit point.

THIS IS NOT A FRENCH DRAIN!

A Surface Drain may come in many different shapes or sizes.  The Drain Grate may be round or square.  Here is a picture of a common Surface Drain.

Cutting the Curb for a French Drain Outlet

Surface Drain and Drainpipe

A Channel Drain is a type of Surface Drain, and many times is installed in

Channel Drain
 

4 Inch Drain Pipe Ready to be covered with dirt in Norman.
4 Inch Drainpipe Ready to be covered with dirt in Norman.

 

Sprinkler System Checkup Norman.

Lots of things can be done to make sure your Sprinkler System is ready to go.  All the Sprinkler Zones should be checked one by one.  The sprinkler heads and valves need to be checked to see if anything needs to be adjusted or replaced.

Sprinkler System Checkup is a Service Provided by Oklahoma Drainage since 1993.

Today we did a sprinkler repair in Norman.  The sprinkler system needed a checkup.

We went through each sprinkler zone and identified several different problems.

Zone 2 had a cracked sprinkler pipe in a flower bed.

A broken Rotor Sprinkler head was found immediately.

Next, zone five look good with no problems.

Zone 6 and 7 each had a couple of pop-up spray heads that were worn out and would not pop-up.  The diagnosis and the repair took less than two hours.  Now their sprinkler system is running great!

Now is a good time to have a Sprinkler System Checkup provided by Oklahoma Drainage.

Sprinkler Systems need to be checked before winter to prevent pipes from freezing.  Sprinkler Design determines whether sprinkler lines need to be bled.  Emergency shut off valves also need to be checked and turned off for the winter.

In the Spring, all the water needs to be turned back on and all sprinkler zones and heads need to be tested.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provide Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

Sprinkler Valves

Sprinkler Valve Replacement is a service that Oklahoma Drainage has provided Since 1993.  Recently we removed 3 Rainbird Sprinkler Valves and replaced them with new ones.  The valves had been crushed accidentally when a landscaper drove his truck across the yard.

Sprinkler System Check-Up in Edmond, Oklahoma City, Norman, and Moore.

 

 

Sprinkler System Check-Up process is very straightforward.  We run through all the Sprinkler Zones one-at-a- time from the controller. 

Sprinkler Controller

Sprinkler controllers can be a problem source.   Many times, the wires in the controller are loose or have a “Short” in one of the wires.  Sprinkler Programming can be a source of frustration.  We can help with Programming your controller.

We check all the sprinkler heads in that zone and the valves as well.

Once the Sprinkler System Checkup is Complete, we provide a Quote for what it will cost to make the needed repairs.

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes – Sprinkler Head Adjustment – Sprinkler Valve Replacement

Servicing all of Central and Western Oklahoma since 1993.  405 203 9419

Sprinkler Valve Replacement is a service that Oklahoma Drainage has provided Since 1993.  Recently we removed 3 Rainbird Sprinkler Valves and replaced them with new ones.  The valves had been crushed accidentally when a landscaper drove his truck across the yard.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provide Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

First Step

First, we dug up a good working area surrounding the broken Sprinkler Valves.  Next, we cut out the broken valves and crushed PVC pipes.  Finally, PVC pipe was cut and glued with new Sprinkler Valves following the original design and configuration.  In this case the three original sprinkler valves were connected to each other inside one Valve Box.

We aren’t done yet though; two sprinkler wires must be connected to each Valve.  One sprinkler wire is the “Common Ground.”  The other wire is the power wire.  All the sprinkler wiring is connected with water-proof wire connections.

The Common Ground wire and the Individual Power Wires all come from the Sprinkler Controller.  Each Sprinkler Valve has its own power wire coming from the Controller.  All the Sprinkler Valves are Connected to the Same Common Ground Wire.

Before We Finish

Before dirt can be put back around the new valves, testing must be done.  Each valve must be turned on, “one-at-a-time,” at the Controller to ensure good wire connection and functionality.  Also, the Sprinkler Valves must be checked for leaks in the PVC Pipe.

Oklahoma Drainage and Sprinkler Repair provides Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

Blanchard Sprinkler Repair has been provided by Oklahoma Drainage and Sprinkler Repair since 1993.

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,     Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

Sprinkler Head Installation

Lawton Sprinkler Repair, Service, Photos of Drainage Systems – French Drain Installation

Posted: September 12, 2014 in sprinkler repair, sprinkler repair contractor, Sprinkler Repair Service
Tags: , , ,
7

We service all of Central and Western Oklahoma

Since 1993 we have:

Fixed leaking sprinkler pipes in Edmond

Replaced Sprinkler Valves in Norman

Adjusted Sprinkler Heads In Oklahoma City

Installed A New Back Flow Valve in Lawton 

and over 2000 other Sprinkler Repairs in Central and Western Oklahoma.

Sprinkler Repair in Oklahoma City.

Recently we spent an afternoon checking out a Sprinkler System in Northwest Oklahoma City.  The customer told us that many of the heads in the Sprinkler System had a variety of problems.  Her Sprinkler System was fairly large so the Sprinkler System Checkup would take some time.

Sprinkler Valve Replacement

Sprinkler Valve Replacement

Sprinkler System Checkup

First, we had to run each Sprinkler Zone and look at each Sprinkler Head individually.  This took a while considering that there were 18 zones and 5 to 10 Sprinkler Heads in Each Zone.

 

First we looked to see if each Sprinkler Head was functioning correctly.  Many of the heads were leaking at the base. Other Sprinkler Heads were not spraying correctly and needed to have their Sprinkler Nozzles Replaced.  Some of the Sprinklers were just worn out and needed to be replaced.

 

As we went through the Sprinkler System, we placed a flag by each head that needed some type or Sprinkler Repair or Replacement.  Along the way we also checked Sprinkler Coverage.  Some Sprinkler Heads needed to be moved because some areas were either too dry or too wet.  Several Sprinkler Heads needed to be moved.

 

 

Before the end of the day, we replaced 12 Sprinkler Heads, Changed Out 35 Sprinkler Nozzles, and moved 11 sprinkler heads to new locations.

Norman Sprinkler Repair – 

Recently we had a customer in Norman who had some trouble with a sprinkler head that was leaking at the base.  There was mulch all around the sprinkler head and when the system ran it blew mulch all over the sidewalk.  This is a typical Sprinkler Repair and occurs quite often.  It took us about 15 minutes to fix.  We also moved several Sprinkler Heads that weren’t in the best places.  Moving sprinkler heads is a common practice for Oklahoma Drainage and Sprinkler Repair.

 

Sprinkler Repair is an ongoing issue for any sprinkler system.

Moving sprinkler valves also is a service that we provide.  It takes a lot more expertise and experience to move sprinkler valves.  There are many reasons that sprinkler valves and sprinkler heads may need to me moved.  Driveways can be added or new landscaping may be installed.  We can redesign any residential sprinkler system.  Moving Sprinkler Valves, Sprinkler Heads, Sprinkler Pipes, and Sprinkler Wiring is what it takes.

Sprinkler Service

Just like a home or a car, a Sprinkler System requires repair or adjustment from time to time.  We at Oklahoma Drainage and Sprinkler Repair, take great pride in the Sprinkler Repair Services that we provide.  In almost 27 years of service, we have solved virtually every Sprinkler Repair Problem possible

We solve Sprinkler Repair Problems that other companies can’t handle.  If you live in Oklahoma City and have Broken Sprinkler Heads, or if you live in Norman and have Leaking Sprinkler Valves, or if you live in Edmond and your Sprinkler Controller quit working, give us a call or send us an

Lawn Sprinkler Repair is one of our business focuses.   We can help with:

1. Sprinkler Controller Problems

2. Leaking Back-Flow Valves

3. Leaking Sprinkler Pipes

4.  Shorted or disconnected valve wires

5. Sprinkler Zones or Sprinkler Stations that won’t work

6. Broken Sprinkler Heads

The above are the most common problems that we deal with.

 

Edmond Sprinkler Repair

 

Sprinkler System Repair — Broken Sprinkler Heads — Sprinkler Controllers — Sprinkler Valves — All Brands

Servicing:  Oklahoma City — Norman — Moore — Edmond — Mustang — Yukon — Midwest City — Del City — Blanchard — Newcastle 

AND ALL CENTRAL OKLAHOMA.

Now Servicing Western Oklahoma including Lawton and Altus.

 

Fixing Leaking Sprinkler Pipes is a common occurrence for Oklahoma Drainage and Sprinkler Repair.  Most recently we had a service call in Lawton.  We got a call from a lady who had water pouring out from under the edge of her driveway.  After shutting off the water at the back-flow valve, we were able to determine that the leak definitely was coming from the sprinkler system.  A cracked sprinkler pipe was the problem and to make matters worse, the sprinkler pipe ran under the driveway.

Oklahoma Drainage and Sprinkler Repair had the solution.  Instead of trying to fix the broken sprinkler pipe, it was a much better idea to replace the entire pipe.  The Sprinkler Repair took about three hours.

Oklahoma City Sprinkler Repair

Recently we helped some folks with their sprinkler controller.  They had a lightning strike melting their sprinkler controller and all the connecting wires. Changing the Sprinkler Controller took a little time, but the larger problem was changing out all the sprinkler wires that ran underground form the controller to the sprinkler valves.  This part took a while and required quite a bit of attention to detail.

SPRINKLER REPAIR IN OKLAHOMA CITY –

Sprinkler valve repair

Sprinkler Valve Installation

The sprinkler valve in the picture was replaced by Oklahoma Drainage and Sprinkler Repair. When the Sprinkler Valves were originally installed, they were not put inside a “Valve Box” to protect them. The company that installed them just dumped dirt on them and got paid and left.

The Sprinkler System ran ok for about two years before the sprinkler valves failed. We replaced the valves and added a valve box to protect them so this time the Rain Bird valves should last much longer. If you need help with your sprinkler system, give us a call at 405 203 9419. Oklahoma Drainage and Sprinkler Repair has been solving sprinkler problems since 1993.

Oklahoma Drainage and Sprinkler Repair – 405 203 9419

Do you need Sprinkler Repair?

Winter is a time when a lot can go wrong with a Sprinkler System.   Sprinkler Pipes can freeze and break.  Sprinkler heads can crack or bust.  Above Ground Back-Flow Valves can crack or leak even during a warm winter.  Oklahoma Drainage and Sprinkler Repair can help.  Give us a call at:

Sprinkler Controller

Oklahoma City Sprinkler Repair

Sprinkler Controller Trouble Shooting —

Having Installed Several Thousand Sprinkler Systems over the past several years, here are the most common mistakes made by homeowners who are not comfortable with their Sprinkler Controller.

Most Sprinkler Controllers have a knob or a digital touch screen.  Either way, the basic functions are the same.

1.  Sometimes some brands of Sprinkler Controllers won’t work because the ” Time and Date,” have not been set correctly.  If you select time/date and the screen is blank with no time or date then you have a problem.

*******************************************************************************************************************************

2.  The most common reason that a Sprinkler Controller

won’t work is because the breaker has been tripped for the electrical plug that the controller is plugged into.  People assume that because the LED screen on the controller has power that the controller is receiving power.

THIS IS NOT THE CASE!!!!!!!!!!!!!!!!   CONTROLLERLS HAVE BACKUP BATTERIES IN THEM TO MAINTAIN THE PROGRAMMING IF YOUR ELECTRICITY GOES OFF.  THE BREAKER CAN BE TRIPPED TO THE ELECTRICAL OUTLET AND THE DIGITAL DISPLAY WILL STILL RUN OFF THE BATTERY MAKING IT LOOK LIKE IT HAS POWER WHEN IT DOES NOT.

TEST YOUR OUTLET BY CHECKING YOUR BREAKERS OR PLUGGING SOMETHING INTO THE SOCKET SUCH AS A LIGHT OR A POWER TOOL.

********************************************************************************************************************************

Another very common mistake

is that people confuse “Start Times,” with “Run Times” on the controller.

A Run Time is how long you program each Sprinkler Zone to run.

(Zone 1  5 minutes, Zone 2 8 minutes, Zone 3 25 minutes and so on.)  You program how long you want each Sprinkler Zone to run.

A Start Time is a time that you set on the controller to start zone one running.  All other zones automatically follow zone one in order lowest to highest.  Zone 2 knows to always follow zone 1 when it is done.  Zone 3 knows to follow Zone 2 and so on.  Let me repeat this.  Start Times are only for zone 1.  Again, a “Start Time,” is a time that you would like your Sprinkler System to come and run through all the zones.

Sprinkler Controllers have the ability to run more than one start time.  This is to allow your entire Sprinkler System to run more than once in a 24-hour period.  You can have a Start Time of 1 PM.  Zone 1 comes on and runs until its programmed time elapses.  Zone 2 automatically comes on next and runs.  Then zone 3 and so on.  You might have a 2nd Start Time several hours later to start and run your entire system again.  (2nd start time at 8 PM)  The Sprinkler System has had plenty of time to run through all the zones when it started at 1 PM.  At 8 PM the controller turns zone 1 on again and all the zones run their programmed amount of time.

THE MISTAKE PEOPLE MAKE

IS THINKING THAT YOU MUST PROGRAM A START TIME FOR EACH ZONE. ( YOU CAN NOT PROGRAM A START TIME FOR ZONE 2,3,4 etc.)  This is also apparent by the fact that most Sprinkler Controllers have a limit of 4 start times but can run more zones than 4.  Most Sprinkler Controllers can run 10 zones or more.

What causes a big problem is a when person programs a Start Time at 1Pm.  Thinking incorrectly that they need to program a Start Time for zone 2.  They enter a second Start Time for 1:15pm, and a third start time for zone 3 at 1:30 PM.  So here is what happens.  Say each zone is programmed to run for 10 minutes each.(Run Time)  Zone 1 comes on and runs at 1 PM.  At 1:10 PM Zone 1 stops and zone 2 comes on.  At 1:15 PM the second start time kicks in and tries to turn on zone 1 again while zone 2 has only been running for five minutes and the other subsequent zones have not run at all.

This is called an “Overlapping Start Time.”  With an Overlapping Start Time, Different brands of controllers do different things.  They are all bad regardless.  Some will run zone one over and over and over causing a flood.  Others will not run at all.

Most people only use or need one Start Time.

********************************************************************************************************************************

The “Water Budget Feature,

” found on most controllers can cause problems with your Sprinkler Run Times.  Water Budget is a quick way to quickly change all your Run Times for all your zones at once.  Example — Out of the box, your new Sprinkler Controller will be set to 100%.  If you program zone 1 to run 10 minutes and zone 2 to run 15 minutes, then if your water budget is 100% then that is exactly what they will run.  If you change your water budget from 100% to 200% now zone 1 will run 20 minutes and zone 2 will run 30 minutes and any other zone’s run time will run double of what it was programmed at 100%.  This is a great feature until you accidentally change your water budget to 900% and don’t realize it.  (or 5%)

IF YOUR RUN TIMES ARE RUNNING MORE OR LESS THAN WHAT YOU PROGRAMMED THEM FOR THEN CHECK THE WATER BUDGET.

********************************************************************************************************************************

Some of the older digital Sprinkler Controllers have an “Enter” button.  Any programming you do must be followed by hitting the Enter Button.  If you don’t hit it then programming that you think you keyed in is lost.  This is why the newer controllers don’t have an Enter Button.

 

Oklahoma Drainage and Sprinkler Repair has been solving all types of Sprinkler System Problems since 1993.

We provide:

1.  Sprinkler Valve Problems

2.  Sprinkler Wiring Problems

3.  Sprinkler Controller Problems / Sprinkler Clock Problems

4.  Sprinkler Head Problems

5.  Sprinkler Pipe Problems

6.  Sprinkler Coverage Problems

7.  Sprinkler Redesign Problems for new fences or swimming pools.

 

Many times, sprinkler repair needs arise at inconvenient times. Water lines can break in the middle of the night.  Back-Flow Valves Freeze and break at night too.

Sometimes things go wrong when we are away from our homes as well.  Sprinkler Systems coming on at the scheduled times but not shutting off is common and has several possible causes.  Sprinkler Valves can “stick” open while running from lack of water pressure or is not getting enough electrical current to shut it off from the sprinkler controller, or even a small piece of debris is stuck in the sprinkler valve and won’t allow the sprinkler valve to close.

Oklahoma Drainage– We install French Drains, Channel Drains, Surface Drains, Sump Pumps and Sod.

If You live in Oklahoma City and water damaging your foundation, We can install a French Drain for you.

If you live in Norman and have water standing on your driveway, We can install a Channel Drain for you.

If you live in Edmond and have water flooding your basement, We can install a Sump Pump for you.

If you live in Moore and have water washing out your flower bed mulch, We can install a Surface Drain for you.

If you live in Yukon and need grass to grow, we can install Sod too!

Servicing All of Central and Western Oklahoma Since 1993.

Oklahoma Drainage – Servicing all of Central and Western Oklahoma

In business since 1993, we solve all types of Residential Drainage  Problems.   We utilize French Drains, Surface Drains, Channel Drains and Sump Pumps in our Drainage Systems depending on what the customer’s needs are.

 

A French Drain Can Handle Standing Water

Surface Drains installed in Edmond

Surface Drains installed in Edmond

 

 

Check out some of or recent work!

Running solid Drain Pipe From French Drain in Back Yard to Curb

Running solid Drainpipe From French Drain in Back Yard to Curb

Installation of a Drainage System, French Drain, In Norman Oklahoma

Installation of a Drainage System, French Drain, In Norman Oklahoma