Archive for the ‘Oklahoma City French Drain’ Category

French Drain Contractor Norman.

Oklahoma Drainage 405 203 9419 — We provide:

    French Drain Installation, Surface Drain Installation, Drainage System Installation

Oklahoma Drainage –  We install French Drains, Channel Drains, Surface Drains, Sump Pumps and Sod.

If You live in Oklahoma City and water damaging your foundation, We can install a French Drain for you.

If you live in Norman and have water standing on your driveway, We can install a Channel Drain for you.

If you live in Edmond and have water flooding your basement, We can install a Sump Pump for you.

If you live in Moore and have water washing out your flower bed mulch, We can install a Surface Drain for you.

If you live in Yukon and need grass to grow we can install Sod too!

 FRENCH DRAIN IN EDMOND OKLAHOMA, DRAINAGE CONTRACTOR

Oklahoma Drainage and Sprinkler Repair Recently  installed a large 6 inch French Drain in Edmond.  The customer had water running under his back porch step and into his basement.  We did a Free Drainage Diagnostic and Estimate.  The French Drain design that we proposed would intercept the surface water and subsurface water that was flowing under the steps.  The French Drain design called for a 6 inch French Drain to be installed above and several feet away from the steps.  It would run around the house parallel to the foundation and about 5 feet to the East.  The French Drain would run past the steps to a point where water must cross the French Drain or run up hill to the steps which in this case was not possible.  Once past the steps, the French Drain would transition to Solid 6 inch Drain Pipe and continue on around the house to the Pop-Up Emitter down hill in the side yard.  Along the way we attached several Gutter Down Spouts into the French Drain.

French Drain is completely different from a Surface Drain.  A basic French Drain consists of a Perforated Drain Pipe in the bottom of a trench.  A  Trench Liner is sometimes used depending on the Drainage System Design and the type of soil.   The Drain Pipe should have a neoprene sock around the Perforated Drain Pipe.   This is to ensure that the Drain Pipe does not become clogged. A trench is dug that is slightly wider than the French Drain Pipe that is being used.  There are several sizes of French Drain Pipe.   Three Inch, Four Inch, and Six Inch are the most common sizes of French drain Pipe. The dirt that is taken out to make the trench is hauled away.  It is replaced by some type of small stone or gravel depending on what is desired or available.  I prefer crushed 1 inch lime stone.  It is the most economical option in my area.  Pea Gravel or some other type of small stone can work just as well.    The lime-stone or gravel is placed in the trench on top of the perforated Drain Pipe and filled all the way to the surface (ground level).   In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drain Pipe or the Gravel are installed.  This helps maintain the integrity of the trench over time.  It also increases the cost of the French Drain and the amount of time to install it.  I install a trench liner in a French Drain  most of the time.

A French Drain is designed to handle a large volume of water and cover a large area. The Drain is anyplace the trench goes. It has many applications and can be used in many situations.  It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Down-Spouts connected to it.

The main downfall of a French Drain is that they, for the most part aren’t very pretty.  They don’t look very nice in a yard once they are completed.
Depending on the area the French Drain is installed and the type of grass around the French Drain, will dictate whether grass grows over the lime stone.  Grass can grow up and through the gravel in the French Drain over time eventually covering the gravel.  This is OK.  It won’t have a measurable effect on the performance of the French Drain.  In some cases thick grass growing up through the French Drain will create a natural “Thatch” filter.  This makes the French Drain invisible.  The trick is to allow the grass to grow over the French Drain Gravel without covering it up with dirt.  Grasses such as Bermuda which grow well in the sun will put out runners and new roots and will grow up and through the French Drain.  This will not affect the performance of the French Drain.  The problem is that some times depending on the type of soil involved, it may take a long time to completely cover up the French Drain.  Sprinkling grass seed down in the gravel will speed up the process.
DON’T COVER THE GRAVEL IN THE FRENCH DRAIN WITH DIRT.  THE FRENCH DRAIN WON’T WORK IF THE TRENCH IS CLOGGED WITH DIRT.  DON’T EVEN INSTALL IT IF YOU ARE GOING TO COVER IT UP WITH DIRT.   
If you install a French Drain in a sunny area, you can:
                                         A.  Leave the  French Drain as-is and allow grass to grow over it in time.
                                         B.  Add grass seed directly to the French Drain gravel with (Light Hand Watering) to speed the growth process
                                         C.  Leave the French Drain as-is but decorate it with stepping stones and landscaping rocks ( leaving large cracks between stones to allow water to get into the French Drain,
2
If you install a French Drain in a shady area you can:
                                        A.  Leave the French Drain as-is, it will work well and look as it did for many years.

B.  Leave the French Drain as-is, but decorate it with stepping stones or landscaping rocks.  Many French Drains are hidden under rock walk ways.

 

 

 

French Drain Running Through Low Areas in Yukon

French Drain Running Through Low Areas in Yukon

 

 

Installing a Drain Pipe For a French Drain that Releases water through a Pop-Up Emitter at the Street

Installing a Drain Pipe For a French Drain that Releases water through a Pop-Up Emitter at the Street

 

 

 

 

Drainage Systems, French Drains, Surface Drains, Channel Drains, Sump Pumps, 

A Channel Drain is a type of Surface Drain and many times is installed in concrete across sidewalks or driveways.  It is long and narrow with a grate on top.

A French Drain is completely different from a Surface Drain.  A basic French Drain consists of a Perforated Drainpipe in the bottom of a trench.  A  Trench Liner is sometimes used depending on the Drainage System Design and the type of soil.   The Drainpipe should have a neoprene sock around the Perforated Drainpipe.   This is to ensure that the Drainpipe does not become clogged. A trench is dug that is slightly wider than the French Drainpipe that is being used.  There are several sizes of French Drainpipe.   Three Inch, Four Inch, and Six Inch are the most common sizes of French drainpipe. The dirt that is taken out to make the trench is hauled away.  It is replaced by some type of small stone or gravel depending on what is desired or available.  I prefer crushed 1 inch limestone.  It is the most economical option in my area.  Pea Gravel or some other type of small stone can work just as well.    The limestone or gravel is placed in the trench on top of the perforated Drainpipe and filled all the way to the surface (ground level).   In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drainpipe, or the Gravel are installed.  This helps maintain the integrity of the trench over time.  It also increases the cost of the French Drain and the amount of time to install it.  I install a trench liner in a French Drain about 20% of the time.  Most of the time a liner in not needed.

French Drain in Edmond Oklahoma

French Drain in Edmond Oklahoma

A French Drain is designed to handle a large volume of water and cover a large area. The Drain is anyplace the trench goes. It has many applications and can be used in many situations.  It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Down-Spouts connected to it.
The main downfall of a French Drain is that they, for the most part aren’t very pretty.  They don’t look very nice in a yard once they are completed.
Depending on the area the French Drain is installed and the type of grass around the French Drain, will dictate whether grass grows over the limestone.  Grass can grow up and through the gravel in the French Drain over time eventually covering the gravel.  This is OK.  It won’t have a measurable effect on the performance of the drain.
DONT COVER THE GRAVEL IN THE FRENCH DRAIN WITH DIRT.  THE FRENCH DRAIN WON’T WORK IF THE TRENCH IS CLOGGED WITH DIRT.  DON’T EVEN INSTALL IT IF YOU ARE GOING TO COVER IT UP WITH DIRT.
DECORATIVE STONE CAN BE USED TO COVER A FRENCH DRAIN AND THEY LOOK GREAT AND LAST A LIFETIME.

 

Information on French Drains

Edmond is one of the communities in Central Oklahoma that Oklahoma Drainage services.  We have installed almost a thousand French Drains in the Edmond community in the past 21 years.  Edmond has many hills and valleys.  Many Neighborhoods are built on hillsides.  This causes many Drainage Problems.  We have installed French Drains by themselves and as a part of Drainage Systems to protect Driveways, Sidewalks, Foundations all over Edmond.  French Drains may be installed in Flower Beds or grassy areas too.  French Drains when installed correctly can provide many years of property protection and Piece of Mind.

Here is a description of other recent work.

A little bit North of Downtown Oklahoma City, Oklahoma Drainage installed a 6 inch French Drain between two businesses which were less than three feet apart.  The French Drain went between a Law Firm and a Tire shop.  Water was leaking through the walls of both businesses.  Gutters between the two establishments were dumping a huge amount of water.  We installed a 6-inch French Drain between the gutters.

It took a long time to get the dirt out of the trench for the French Drain.  It was a very tight fit.  We had to use a little red wagon to haul out the dirt for the French Drain and haul back in the crushed limestone for the French Drain.  It looked a little silly, but it was the only thing we could find that was narrow enough to fit between the buildings.  A French Drain that normally would take 1 day to install took three.

 

The French Drain had a Double Exit Point.  This means that once water entered the French Drainpipe, it could run South to the street, or it could run North to the alley.  To exit points greatly increases the water capacity for any French Drain.

Pop up emitters

Pop up emitters for French Drain

Along the course of the French Drain, we connected two large gutters directly into the Drainpipe.

Once in place, the French Drain eliminated all the water that was leaking into the two buildings.

Drainage Problem Solved!

 

 

FRENCH DRAIN, SURFACE DRAIN PHOTOS AND INFORMATION

 

 Standing water can cause many types of property damage ranging from foundation problems to cracked sidewalks and dead plants and shrubs.  If you have need of French Drain or Surface Drain, give us a call.  We provide free estimates for all of central Oklahoma.

French Drain With Colored Gravel in Oklahoma City

French Drain With Colored Gravel in Oklahoma City

 

Installing Cement around Curb Fitting for French Drain in Norman

Installing Cement around Curb Fitting for French Drain in Norman

Some Drainage Systems are complex and incorporate several types of drains.  Most Drainage Systems , however are basic and require just one type of Drain.  Oklahoma Drainage installs a variety of drains to solve a variety of problems. French Drains, Surface Drains, and Channel Drains are most commonly used.  If you live in Edmond and need a Channel Drain installed across your driveway, or if you live in Norman and need a French Drain in your backyard, or if you live in Oklahoma City and need a Surface drain installed next to your sidewalk, give us a call.    405-226-0629

Channel Drain Installed by CMG In Yukon

Channel Drain Installed by Oklahoma Drainage In Yukon

Channel Drains are one kind of Surface Drain that we install in concrete.

The most common Drain that we install is the French Drain.  This is because the French Drain is versatile.  It can handle Surface Water Problems or Underground Water Problems (sub-surface).  A huge mistake that many people make is assuming that water gets to a Problem Drainage Area by flowing over the surface only.  For example, if water is flowing down hill underground toward your home’s foundation, the only way to stop or intercept it is with a French Drain.  Water can flow laterally into a perforated French Drain Pipe.  It is then diverted away from the Problem Drainage Area to an Exit Point.

Popup Emitter to release water from a French Drain in Yukon

Popup Emitter to release water from a French Drain in Yukon

Pop Up Emitters can release water from Surface Drains or French Drains.  They can release water on to sidewalks or driveways, or out in the middle of yards.

 

 

 

A French Drain is completely different from a Surface Drain.  A basic French Drain consists of a Perforated Drainpipe in the bottom of a trench.  A Trench Liner is sometimes used depending on the Drainage System Design and the type of soil.   The Drainpipe should have a neoprene sock around the Perforated Drainpipe.   This is to ensure that the Drainpipe does not become clogged. A trench is dug that is slightly wider than the French Drainpipe that is being used.  There are several sizes of French Drainpipe.   Three Inch, Four Inch, and Six Inch are the most common sizes of French drainpipe. The dirt that is taken out to make the trench is hauled away.  It is replaced by some type of small stone or gravel depending on what is desired or available.  I prefer crushed 1 inch limestone.  It is the most economical option in my area.  Pea Gravel or some other type of small stone can work just as well.    The limestone or gravel is placed in the trench on top of the perforated Drainpipe and filled all the way to the surface (ground level).   In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drainpipe, or the Gravel are installed.  This helps maintain the integrity of the trench over time.  It also increases the cost of the French Drain and the amount of time to install it.

 

 

Pipe running to street form French Drain in back yard.

Pipe running to street form French Drain in back yard.

When we run Drainpipe across yards to an Exit Point, the sod usually can be put back into place and in a few days you can’t tell a French Drain was ever Installed.
A French Drain is designed to handle a large volume of water and cover a large area. The Drain is anyplace the trench goes. It has many applications and can be used in many situations.  It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Down-Spouts connected to it.
The main downfall of a French Drain is that they, for the most part isn’t very pretty.  They don’t look very nice in a yard once they are completed.
Depending on the area the French Drain is installed and the type of grass around the French Drain, will dictate whether grass grows over the limestone.  Grass can grow up and through the gravel in the French Drain over time eventually covering the gravel.  This is OK.  It won’t have a measurable effect on the performance of the French Drain.  In some cases thick grass growing up through the French Drain will create a natural “Thatch” filter.  This makes the French Drain invisible.  The trick is to allow the grass to grow over the French Drain Gravel without covering it up with dirt.  Grasses such as Bermuda which grow well in the sun will put out runners and new roots and will grow up and through the French Drain.  This will not affect the performance of the French Drain.  The problem is that some times depending on the type of soil involved, it may take a long time to completely cover up the French Drain.  Sprinkling grass seed down in the gravel will speed up the process.

DON’T COVER THE GRAVEL IN THE FRENCH DRAIN WITH DIRT.  THE FRENCH DRAIN WON’T WORK IF THE TRENCH IS CLOGGED WITH DIRT.  DON’T EVEN INSTALL IT IF YOU ARE GOING TO COVER IT UP WITH DIRT.   

Installing a Curb Outlet for a French Drain in Oklahoma City

Installing a Curb Outlet for a French Drain in Oklahoma City

If you install a French Drain in a sunny area, you can:
                                         A.  Leave the French Drain as-is and allow grass to grow over it in time.
                                         B.  Add grass seed directly to the French Drain gravel with (Light Hand Watering) to speed the growth process
                                         C.  Leave the French Drain as-is but decorate it with steppingstones and landscaping rocks (leaving large cracks between stones to allow water to get into the French Drain,
2
If you install a French Drain in a shady area, you can:
                                        A.  Leave the French Drain as-is, it will work well and look as it did for many years.

                                        B.  Leave the French Drain as-is, but decorate it with stepping stones or landscaping rocks.  Many French Drains are hidden under rock walk ways.


 

Installing Surface Drain System in Edmond Oklahoma

Installing Surface Drain System in Edmond Oklahoma

Sometimes Surface Drains make more sense when the Drainage Problem area is fairly small with Surface Water Flowing into it.

  Oklahoma Drainage also installs a variety of other types of Drains.  Our Drainage Systems may utilize: French Drains, Surface Drains, Channel Drains, Trench Drains, Basin Drains, and Sump Pumps.  In the past 21 years, we have installed French Drains to keep water away from home and business foundations, Surface Drains to keep water away from sidewalks and driveways, Trench Drains, and French Drains to keep standing water out of flowerbeds and yards, and Sump Pumps to remove water from basements and outdoor low-lying areas.

French Drain with stepping stones

French Drain with steppingstones

Lawn Sprinkler Leak Repair

Lawn Sprinkler Repair

Lawn Sprinkler Leak Repair

Lawn Sprinklers can have pipes that leak.   PVC Pipe is the most common Sprinkler System Pipe and leaks definitely are possible.

Leaking Sprinkler Pipes

Leaks can occur near Sprinkler Valves.  Water travels through Sprinkler Valves and can leak going in or coming out.

Many Cities require a back-flow valve to protect the City’s water supply.  It can also leak as water passes through the valve.

Leaks can also occur due to tree roots stressing Sprinkler Pipes.  The pipes can be twisted by roots and crack or break.

Water inside Sprinkler Pipes can freeze and break or crack the PVC Pipe.

Move sprinkler heads, Norman, Oklahoma City, Edmond

There are many reasons for moving Sprinkler Heads.

If you put in a new pool, most of the sprinkler heads will need to be moved.

Sprinkler Heads need to be moved if you have new landscaping installed.

Sometimes Sprinkler Heads weren’t in a good place to begin with.  They need to be moved!

Oklahoma Drainage and Sprinkler Repair can help.  We have been moving Sprinkler Heads since 1993.

In 32 years, we have moved a lot of Heads for Customers in Central and Western Oklahoma.

 

Oklahoma Drainage and Sprinkler Repair provide Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

Emergency Sprinkler Repair is also available.

405 203 9419

Sprinkler Head Installation

Moving Sprinkler Head

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,   Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

We started with the Valves

The Sprinkler Valves were located in the back yard near the pool.  Six valves were located in one place.  They were very tightly connected in one Manifold.  None of the Sprinkler Valves had worked in a long time.  They were Toro Valves that were over 20 years old.  They all had to be replaced.

Surprisingly there was no shut-off valve for the Sprinkler Water.  The water had to be shut off at the Meter so we could install a Manual Shut off valve.  Once installed, the water was turned back on that ran to the house.   The water that ran to the Sprinkler System was shut off with our New Shut Off Valve.

Rainbird Sprinkler Valve

Rainbird Sprinkler Valve

The Sprinkler Valves Were Removed

Now, the 6 valves had to replaced.  The valves that were used were made by Rain Bird.  Before we began, I had to talk to the Customer.  The previous valve design was a bad idea to repeat.

The original Sprinkler Valves were crammed into one large valve box in one very tight manifold.  This is bad because the valves were too close to the fittings.  Simply put, if one valve had to be replaced or worked on in the future, all 6 valves had to be taken out and replaced.   If one valve was bad and 5 worked fine, they all still had to be replaced.

That’s Stupid!

I recommended that an additional Valve Box be installed putting 3 valves in each Valve Box.  This would allow plenty of space between the valve fittings.  If one Sprinkler Valve had to be adjusted or replaced in the future, the other 5 valves need not be disturbed.  Simple Enough!

Check For Leaks

Once the valves were replaced and working, it was time to turn on each Sprinkler Zone, one at a time.  Water was shooting up from the ground in several places in zone 1.  Two broken Sprinkler Pipes and 5 bad Sprinkler Heads in zone 1 had to be fixed and replaced.  We went through each of the 6 zones in similar fashion fixing lots of leaks and replacing bad sprinkler heads.

The Sprinkler Repair Cost About Half of the Cost of Completely New System.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

Sprinkler Head Adjustment is a service provided by Oklahoma Drainage and Sprinkler Repair.  We have adjusted sprinkler heads since 1993.

Many times, Sprinkler heads get, “Out of Wack.”  Lawn mowers and weed eaters are notorious for this.  Sprinkler heads start spraying water in the wrong place.  It is frustrating to water concrete while plants and grass go without moisture.

Pop-Up Sprinkler Heads

Pop-Up Sprinkler Heads can be adjusted several ways.  How far water goes to the left or right can be increased or decreased.  The distance the water goes can also be increased or decreased.  Finally, how high a sprinkler head pops up can be increased or decreased by installing a taller or shorter head.

Sometimes sprinkler heads spray a reduced distance and don’t perform very well due to water scale.  Minerals in the water can completely clog a Pop-Up.  Usually, the sprinkler nozzle on top of the sprinkler head, need only be replaced without replacing the entire head.

Rotor Sprinkler Heads also can be adjusted to the left or right.  Spray Distance can be increased or decreased as well.

Needs Change

What’s going on in your yard can change.  This calls for Sprinkler Head Adjustment.  Adding or removing a swimming pool changes everything concerning sprinkler heads.  Any number of things can change the necessary sprinkler head coverage.

 

 

Oklahoma Drainage and Sprinkler Repair — Installing – French DrainsSurface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler RepairBroken Sprinkler Pipes Sprinkler Head AdjustmentSprinkler Valve Replacement

We provide Service for Folks in: Norman, Oklahoma City, Edmond, and Moore.

Central and Western Oklahoma is our Service Area since 1993.  

                                                           (405) 203-9419

Check out Sprinkler System Check-Up

Emergency Sprinkler Repair

Sometimes things go wrong with sprinkler systems.

 

IF YOU NEED HELP IN THE MIDDLE OF THE NIGHT OR ON A WEEKEND WITH YOUR SPRINKLER SYSTEM, GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR.  405 203 9419

IT MAY TAKE A FEW HOURS FOR US TO GET THERE BUT WE WILL COME TO HELP.

 

One Common problem is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

 

Inside the valve box is a plastic handle that can turn off the water to the sprinkler system.  It can be blue or red or grey in color.

Many times, the valve box will be full of dirt, and you can’t turn or even see the handle until some of the dirt has been dug out by hand.

 

Water might be shooting up in the air somewhere on your property.  This can be caused by a broken sprinkler pipe or sprinkler valve.

SHUT OFF THE SPRINKLER WATER IF YOU CAN AND GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR. SERVICING ALL OF CENTRAL AND WESTERN OKLAHOMA.

405 203 9419

Servicing Oklahoma City, Norman, Edmond and all of Central and Western Oklahoma

 

 

FRENCH DRAINS SOLVE LOTS OF DRAINAGE PROBLEMS!

 

We just finished a 4 inch Drainage System in Yukon.  It was a complicated system to install.  It utilized 4 inch French Drain in the flower beds,  12 inch Surface Drains on the side of the house,  6 inch French Drain along the garage foundation with 2 Pop – Up Emitters in the back yard and 3 Curb Fittings in the front.    First we installed 4-inch French Drain in the flowerbeds on both sides of the front door.  We connected 4 inch solid Drainpipe into the French Drain and ran them underside walk to the curb.  Next we cut the curb with a concrete saw and installed 3 curb outlets for 3 separate French Drains.

Installing a Curb Outlet for a French Drain in Oklahoma City

Installing a Curb Outlet for a French Drain in Oklahoma City

Next we installed 4 12 Inch Drain Basins with grates along both sides of the house continuing with Solid Drainpipe to the Pop-Up Emitters on the back fence. Finally we completed the Drainage System by installing a long run of 6 inch French Drain down the side of the garage foundation.

Installing the French Drains in the flower beds

was the most difficult and took the most time.  Each French Drain took over a ton of crushed limestone to fill the French Drain trench.  The Six inch French Drain took even more limestone.

French Drain in Oklahoma City

French Drain in Oklahoma City

French Drains can utilize  several types and sizes of French Drain Pipe.  An older type that is not commonly used any more is 4 inch PVC Pipe with large half inch holes drilled in the Pipe.  This doesn’t work very well,   Because the holes are too large and the number of holes in the French Drain Pipe are too few.  Also there is no filter or “Soc” around this particular French Drain Pipe.  If it is used in sandy or loose soil the holes will clog and the pipe will fill up with sand.  PVC French Drain Pipe should be avoided.

Installing a Drain Pipe For a French Drain that Releases water through a Pop-Up Emitter at the Street

Installing a Drainpipe For a French Drain that Releases water through a Pop-Up Emitter at the Street

ADS French Drainpipe

is much better, the holes are smaller and much more numerous.  It also comes inside a soc that acts as a filter and helps keep sand and debris out of the French Drainpipe.  It works very well.

For Small business and Residential French Drains, Four inch ADS Perf/Soc French Drain pipe is adequate and the most common.  It is used for the majority of all French Drains installed.  French Drains can be installed using 3 inch ADS Perf/Soc but many times it is too small and can be overwhelmed by a heavy rain or from a bad design.  (Too many gutter down spouts connected directly into the French Drain, For Example)  Three Inch French Drain Pipe should be avoided if possible.

Connecting Gutter into French Drain System in Moore

Connecting Gutter into French Drain System in Moore

Six inch  ADS Perf/Soc French Drainpipe is usually a good idea when possible.  It carries a much larger volume of water.  Six Inch French Drains are rarely overwhelmed.

The Drawbacks to 6 inch French Drain installation are:

 
 1.  The Materials Cost is higher for six-inch French Drain Compared to Four Inch Pipe.
                                                                                                                    2.  Many times 6 Inch French Drainpipe is too large for many applications, Such as going under a fence or sidewalk.  
                                                                                                                   3.  The trench for a 6 inch French Drain must be much larger than a 4 Inch
                                                                                                                   4.  The amount of gravel or limestone or River Rock used to Cover the 6 inch French Drain is Much larger
 
All things being considered, the performance and longevity of a 6 inch French Drain is well worth it if you are trying to protect something of value to you!  If the higher cost and the additional labor and materials are not a problem and 6 inch French Drain pipe is not too big for what you want to do then a 6 inch French Drain would be the best.  
 
 

French Drain, Dry Floor Vents, Keeps Water out of AC Ducts.

 

A FRENCH DRAIN CAN KEEP WATER OUT OF AIR CONDITIONING DUCTS

 

French Drain Installation can prevent water from getting into your air conditioner floor ducts.

 

 

A common Drainage Problem

for people in Central Oklahoma is ground water seeping into floor air conditioner  ducts.  This can cause very costly damage to a home or business.  Water-proofing Ducts, or even worse, trying to remove mold from duct work can cost big bucks.   Structural Engineers typically recommend French Drain Installation to keep water out of ducts.

French Drains catch and remove sub-surface water that is traveling underground toward a foundation. It is intercepted by the French Drain before it can seep under the building in question.   Because this water is not usually seen, it may not be taken into consideration when diagnosing drainage problems.  Surface Water traveling to a problem area is obvious as it flows on the surface in plain sight.

We have 32 years of experience Diagnosing Drainage Problems.  We always check for sub-surface water flow into any Problem Drainage Area.  Again, French Drains are intended to handle water moving both underground and above ground.

 

French Drains

can also be used to remove water that is standing in a large area such as up against a foundation or along a fence.  French Drains don’t do so well in tight small areas.  These areas are best suited for a Surface Drain with a grate.  Many times, we install French Drains along foundations after a homeowner has spent large amounts of money on foundation repair.

Surface Drain Installation in Edmond

Surface Drain Installation in Edmond

Several Foundation Repair companies and Duct waterproofing companies recommend Oklahoma Drainage.   Typically, we install a French Drain by itself or as part of a Drainage System  after they have completed their repairs to the foundation or duct work.

 

 

Curb Outlet for French Drain in Edmond Oklahoma

Curb Outlet for French Drain in Edmond Oklahoma

 

Drainage Problems occur in all types of places.

 

Water can stand along fences or driveways, or in yards and flowerbeds.   Damage can be done to sidewalks and in yards.  Finding a good Drainage Solution usually involves a French Drain.

 

French Drain Running Through Low Areas in Yukon

French Drain Running Through Low Areas in Yukon

Oklahoma Drainage provides quality service for central Oklahoma.  If you live in Norman and need a French Drain, or if you live in Oklahoma City and want a Channel Drain installed across your driveway, give us a call.

We have installed Drainage Systems and French Drains in:  Oklahoma City, Edmond, Moore, Midwest City, Norman, Yukon, Mustang, Del City, Blanchard, Newcastle and all surrounding areas.

Recently we installed a French Drain in Norman.

Our customer had water running down the hill from his neighbor’s Sprinkler System into the North wall of his house.  Over time the ground became saturated and water seeped under the wall and into his floor air conditioning vents.

We installed a 4-inch French Drain along the North wall of his house to provide a barrier to the continuous water flow.  In a few days the moss that was growing on the side of his house began to die from lack of water.  A Duct company came in and cleaned out is vents.  The French Drain removed the surface and sub surface water that was flowing into his home.   Problem solved.

 

Sprinkler Repair

Emergency Sprinkler Repair

Sometimes things go wrong with sprinkler systems.

 

IF YOU NEED HELP IN THE MIDDLE OF THE NIGHT OR ON A WEEKEND WITH YOUR SPRINKLER SYSTEM, GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR.  405 203 9419

IT MAY TAKE A FEW HOURS FOR US TO GET THERE BUT WE WILL COME TO HELP.

 

One Common problem is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

 

Inside the valve box is a plastic handle that can turn off the water to the sprinkler system.  It can be blue or red or grey in color.

Many times, the valve box will be full of dirt, and you can’t turn or even see the handle until some of the dirt has been dug out by hand.

 

Water might be shooting up in the air somewhere on your property.  This can be caused by a broken sprinkler pipe or sprinkler valve.

SHUT OFF THE SPRINKLER WATER IF YOU CAN AND GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR. SERVICING ALL OF CENTRAL AND WESTERN OKLAHOMA.

405 203 9419

Servicing Oklahoma City, Norman, Edmond and all of Central and Western Oklahoma

 

 

 

Edmond Oklahoma French Drain Information is a Central Focus for Oklahoma Drainage.  We service all of Central and Western Oklahoma.

Check Out French Drains Installed in Edmond Oklahoma!

Since 1993, Oklahoma Drainage has installed over 1200 Drains in the city limits of Edmond.

Some Simple rules about French Drains and Surface Drains.  A French Drain should be installed when there is a large volume of water to be drained over a large area.  Surface Drains are needed when the water volume is smaller, and the Drainage Area is small and focused.  French Drains move away Surface Water and Sub-Surface water.  Surface Drains move only surface water.

Oklahoma Drainage provides top quality Sprinkler Repair Service.  If you live in Oklahoma City and need a Sprinkler Head moved, we can help.  You might have a Sprinkler Pipe leak that needs attention.  A Sprinkler Valve might we wore out as well.  You might just want a Sprinkler System Checkup for Spring.  For these problems and many others, Oklahoma Drainage can help.

We service Oklahoma City, Norman, Edmond and all of Central and Western Oklahoma.

 

Edmond Oklahoma French Drain Installation, French Drain Repair

Edmond Oklahoma has been the location for many French Drain Installations for Oklahoma Drainage in the past several years.  Recently we ripped out an old Surface Drain that was under a deck.  The Surface Drain was too small for the job and did not Protect the Foundation from Standing Water


 The First step was to take out part of the deck along the wall.  Next, we took out the Surface Drain and the Three Inch Pipe which was too small.  Digging a trench along the foundation came next.  We had to ensure the, “Fall” to make sure the water would run from left to right. 

As Seen above, we also install Channel Drains.
French Drain Installation Next to Wall

French Drain Installation Next to Wall, Installing Trench Liner


 Next a French Drain Liner needed to be installed.  This w

Edmond Oklahoma French Drain Installation is a focus for Oklahoma Drainage.  We service all of Central and Western Oklahoma.  We install French Drains, Surface Drains, Channel Drains and Sump Pumps.  Expert Sprinkler Repair and Sod Installation is also provided.

Oklahoma Drainage – 405 203 9419

 

 

Edmond has lots of Hills

Edmond is one of the communities in Central Oklahoma that we service.  Oklahoma Drainage and Sprinkler Repair has installed almost a thousand French Drains in the Edmond community in the past30 years.

The community has many hills and valleys and as a result, Many Neighborhoods are built on hillsides.  This causes many Drainage Problems.

We have installed French Drains by themselves and as a part of Drainage Systems to protect Driveways, Sidewalks, Foundations all over Edmond.  French Drains may be installed in Flower Beds or grassy areas too.  French Drains when installed correctly can provide many years of property protection and Piece of Mind.

 

 

Curb Outlet for French Drain in Edmond Oklahoma

Curb Outlet for French Drain in Edmond Oklahoma

 

Oklahoma Drainage and Sprinkler Repair — Installing – French DrainsSurface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes Sprinkler Head AdjustmentSprinkler Valve Replacement

We provide Service for Folks in: Norman, Oklahoma City, Edmond, and Moore.

Central and Western Oklahoma is our Service Area since 1993.  

                                                           (405) 203-9419

 

Curb outlet for a French Drain in Edmond

Curb outlet for a French Drain

 

 

French Drain Installation in Nichols Hills

 

French Drain in Oklahoma City

French Drain in Oklahoma City

French Drain Installation in Nichols Hills

 

 

 

 

Oklahoma Drainage Recently installed a Drainage System in Nichols Hills.  The Drainage System was made up of a 4 inch French Drain starting in the back yard.  It ran between the garage and the pool.  Several gutters were connected directly into the French Drain.  From this point, we expanded up to a larger 6 inch Drain pipe to handle the added water into the system from the gutters.  In several places the French Drain had to run through areas where Sprinkler Pipes were in the way.  We had to re-rout all the Sprinkler Pipes and Wires under the French Drain.

Once the Sprinkler System had been redesigned and the gutters had been connected, We ran the 6 inch Drain Pipe from the end of the French Drain, around the house to release through the curb.  We cut the curb and installed a 6 inch curb fitting with acrylic concrete.  A few days later a major thunderstorm poured down on the property.  The French Drain and the Drainage System Worked Perfectly.

Pipe running to street form French Drain in back yard.

Pipe running to street form French Drain in back yard.

If you live in Nichols Hills and need a French Drain, or if you live in Oklahoma City and have water standing on your driveway, or if your back yard turns into a moat ever time it rains, give Us a call

Oklahoma City Drains, French Drains, Surface Drains, Channel Drains.  If you have water in a place that it is not wanted, we can help!

Oklahoma Drainage – We install French Drains, Channel Drains, Surface Drains, Sump Pumps and Sod.

If You live in Oklahoma City and water damaging your foundation, we can install a French Drain for you.

Or if you live in Norman and have water standing on your driveway, we can install a Channel Drain for you.

If you live in Edmond and have water flooding your basement, we can install a Sump Pump for you.

Or if you live in Moore and have water washing out your flower bed mulch, we can install a Surface Drain for you.

If you live in Yukon and need grass to grow, we can install Sod too!

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Sprinkler Valve Replacement

Edmond Sprinkler Repair

Oklahoma Drainage and Sprinkler Repair provide Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

Check out Pictures of French Drains!

French Drain Installation

Oklahoma Drainage

has been diagnosing and solving Drainage Problems since 1993.  Water has the ability to get into places around your home where you really don’t want it to be.  Some drainage problems are easy to solve.  Typically, water enters the problem drainage area one way from one source.  The really tricky drainage problems occur when water enters the problem drainage area from multiple directions and from multiple sources.  Sometimes a secondary water source can’t be seen or identified until the primary water problem source is eliminated.

An example of this occurs when water is running into a problem area in an obvious way over the ground where you can see it.

Simple enough.

Channel Drain Across Driveway

French Drain Connected to a Channel Drain across the Driveway

A drainage system

is installed with a surface drain as the “intake” with drainage pipe running to an exit point.  Initially the water drains away, and everything looks great.  The next day water is back and is all around the surface drain, but below the edge and it hasn’t rained at all, so no additional water ran over the surface of the ground to flood the area.

The primary water source was solved, (The surface water run off) but the secondary water source was not.  Which was sub-surface water, (ground water) running into the area.  A surface drain can’t drain “ground water.”  A French Drain should have initially been installed instead of a Surface Drain.  A French Drain can drain both Surface Water and Ground Water.

Installing 4 Inch French Drain with trench Liner and pipe filter

The White Material is the Trench Liner. The black material is the Pipe Filter.

 

Oklahoma Drainage and Sprinkler Repair — Installing – French DrainsSurface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes Sprinkler Head AdjustmentSprinkler Valve Replacement

We provide Service for Folks in: Norman, Oklahoma City, Edmond, and Moore.

Central and Western Oklahoma is our Service Area since 1993.  

                                                           (405) 203-9419

 

 

 

 

Keep water off your driveway with a channel drain

 Standing water

comes from many sources.  It causes damage to sidewalks, driveways, and foundations not to mention plants, trees, and grass.  Does the side of your house flood because your neighbor doesn’t have gutters, or does your sidewalk turn into a moat after a heavy rain, or worst of all, is water seeping into your foundation and duct work after a thunderstorm? 

Theses are just a few of the Drainage Problems that Oklahoma Drainage and can help with.  We can design a Drainage System to fit your specific needs.  We install many types of Drains to solve many types of problems.    French Drains, Surface Drains, Channel Drains, Basement  Drains, Trench Drains, Basin Drains, and Sump  Pumps are utilized.

 

 

 

We just finished a 4-inch Drainage System in Yukon.  It was a complicated system to install.  It utilized 4 inch French Drain in the flower beds,  12 inch Surface Drains on the side of the house,  6 inch French Drain along the garage foundation with 2 Pop – Up Emitters in the back yard and 3 Curb Fittings in the front.    First we installed 4 inch French Drain in the flowerbeds on both sides of the front door.  We connected 4 inch solid Drainpipe into the French Drain and ran them underside walk to the curb.  Next we cut the curb with a concrete saw and installed 3 curb outlets for 3 separate French Drains.

Next

we installed 4 12 Inch Drain Basins with grates along both sides of the house continuing with Solid Drainpipe to the Pop-Up Emitters on the back fence. Finally, we completed the Drainage System by installing a long run of 6-inch French Drain down the side of the garage foundation.   Installing the French Drains in the flower beds was the most difficult and took the most time.  Each French Drain took over a ton of crushed limestone to fill the French Drain trench.  The Six-inch French Drain took even more limestone.

 Oklahoma Drainage –

Hey Oklahoma, we are expanding to service all of Western Oklahoma as well as Central Oklahoma.  If you live in Elk City, and need a French Drain, we can help.  If water is standing on your driveway in Clinton, Give us a call.  Duncan, Lawton, and Altus are all new areas of service for us.

Since 1993 Oklahoma Drainage and Sprinkler Repair has solved all types of standing water and drainage issues.  We install Drainage Systems that utilize French Drains, Surface, Drains, Channel Drains, and Sump Pumps depending on the customer’s needs.

If you have water in the wrong place, we can help!

 

French Drains as part of a Drainage System – 

Many times people use the term ” French Drain” as general name for a Drain used in or around your home.  French Drains are designed to move a lot of water over a large, flooded area.  They are also designed to take water in on the surface of the ground or below the surface of the ground.  This is very important if the water coming into the flooded area is moving through the ground or coming up from underneath.  ” Sub Surface Water Movement.”  The picture below is not a French Drain!

A French Drain looks like this

A French Drain Can Handle Standing Water

A Oklahoma French Drain Installation, Sprinkler Repair can take in water in a broad area.  It can move a much larger volume of water compared to a Surface Drain.  Also, it can move sub surface water moving into the area where a Surface Drain won’t move any water at all.

Surface Drains

are designed to move surface water only on a smaller scale in confined areas.

Each solves specific drainage problems.  A Drainage System may use one or both together or even several using many types of drains.

Do you have standing water

in a large area in your yard?  Typically, this calls for a French Drain.  A French Drain is a great way to control standing water in a large grassy area.  It can also protect areas from flooding to a certain degree.  As long as the French Drains capacity to move water is not exceeded.

If the French Drains capacity is exceeded, then water will stand in the drainage area until the rain stops and the drain has time to catch up.  A good way to prevent this is to install a bigger French Drain with a larger pipe.  The difference between a 3-inch French Drain and a 6-inch French Drain is huge.

Another way to beef up a French Drain is to connect gutter down spouts in front of the French Drain.  The water coming off the roof causes suction in the French Drain Behind it.  This greatly increases the French Drains ability to move water without increasing the size of the French Drainpipe.

This week

we installed a 6 Inch French Drain in Oklahoma City.  Water was running down the hill, under the back fence, into the back yard, across the sidewalk, and into the side door going into the garage.  After every heavy rain, water was getting into the garage.  We installed a 6 Inch French Drain across the back yard to divert the water.  We also connected the Gutter Down Spouts Directly into the French Drain.

Once the French Drain was downhill from the house, we changed from French Drainpipe to solid 6-inch ADS Drainpipe and continued across the front yard to the street.  Once at the curb, we cut the curb with a concrete saw and installed a Curb Outlet for the French Drain.  Problem solved!

Installing a French Drain outlet through the curb in Oklahoma City

Installing a French Drain outlet through the curb in Oklahoma City

 

 

We also install

a variety of other types of Drains.  Our Drainage Systems may utilize: French Drains, Surface Drains, Channel Drains, Trench Drains, Basin Drains, and Sump Pumps.  In the past 21 years, we have installed French Drains to keep water away from home and business foundations, Surface Drains to keep water away from sidewalks and driveways, Trench Drains, and French Drains to keep standing water out of flowerbeds and yards, and Sump Pumps to remove water from basements and outdoor low lying areas.

French Drain with stepping stones

French Drain with steppingstones

 

French Drains

can be installed by themselves, or as part of a Drainage System that uses other French Drains,  Surface Drains, or other Drain combinations.  Typically, a French Drain is used to protect a broad area that has a lot of standing water.  A French Drain might run alongside a home’s foundation, or beside a driveway, or on any Drainage Project where Sub-Surface water is the primary problem.  If water is running toward your home underground (through sandy soil),

A French Drain is the only Solution for draining away water flowing underground.

 

Installation of a Drainage System, French Drain, In Norman Oklahoma

Installation of a Drainage System, French Drain, In Norman Oklahoma

If you live in Oklahoma City and need a French Drain installed in your yard, or along your driveway, or near your foundation, give us a call.

Or if you live in Edmond or Norman and need a Surface Drain installed in the concrete in your sidewalk or driveway, we can help.  If you live in Mustang or Yukon and would like to protect your trees or flower beds from standing water with a French Drain, We specialize in just that!

 

Servicing: Oklahoma City, Norman, Edmond, Midwest City, Del City, Moore, Yukon, Mustang, Purcell, Blanchard.

 

FRENCH DRAIN CONTRACTOR IN OKLAHOMA CITY, NORMAN, EDMOND 


Oklahoma Drainage –  We install French Drains, Channel Drains, Surface Drains, Sump Pumps and Sod.

If You live in Oklahoma City and water damaging your foundation, We can install a French Drain for you.

If you live in Norman and have water standing on your driveway, We can install a Channel Drain for you.

If you live in Edmond and have water flooding your basement, We can install a Sump Pump for you.

If you live in Moore and have water washing out your flower bed mulch, We can install a Surface Drain for you.

If you live in Yukon and need grass to grow we can install Sod too!

 

French Drain Installation has been an area of focus for us for the past 26 years.  During that time we have installed over 1000 French Drains in the Oklahoma City area.

A French Drain is one of several types of Drains that can make – up a Drainage System.   French Drains are intended to move large amounts of water away from a Problem Drainage Area.  Water may be standing in that area, flowing across the area on the surface, or flowing across the area below ground or “Sub Surface.”  A French Drain can remove Standing Water, Water Flow at ground level, or water flow below ground level. (Surface Drains can’t do this!)

Installing French Drain

The White Material is the Trench Liner. The black material is the Pipe Filter.

 

 

Drain Pipe running from French Drain to the street in Oklahoma City

Drainpipe running from French Drain to the street in Oklahoma City

Recently we installed a Double Six-inch French Drain in Edmond.  A Double French Drain is simple.  Instead of installing one French Drainpipe, You install two French Drainpipes side by side in the same trench.  This is necessary when trying to divert a large volume of water that is moving fast down a steep incline or hill.  The Trench is wider and deeper than normal and can handle a huge volume of water.

A Double French Drain also may be considered when trying to protect a home or important building from potential flooding.  Many times the installation of two French Drains side by side is overkill.  It is done to ensure the customer has piece of mind and never has to worry about potential flooding.

A French Drain many is  used to move water away from or protect foundations.  A French Drain will move both Surface Water and Sub Surface water away from a buildings foundation to an Exit Point where the water can be released without doing damage.

French Drain with colored river rock

French Drain with colored river rock

 

Cutting The Curb and Installing Curb Fitting for French Drain

Cutting The Curb and Installing Curb Fitting for French Drain