Sprinkler Repair Oklahoma City. Oklahoma Drainage and Sprinkler Repair has provided Expert Sprinkler Repair Service in OKC since 1993.
Today we did a sprinkler repair in OKC. The sprinkler system needed a checkup.
We went through each sprinkler zone and identified several different problems.
Zone 2 had a cracked sprinkler pipe in a flower bed.
A broken Rotor Sprinkler head was found immediately.
Next, zone five look good with no problems.
Zone 6 and 7 each had a couple of pop-up spray heads that were worn out and would not pop-up. The diagnosis and the repair took less than two hours. Now their sprinkler system is running great!
Now is a good time to have a Sprinkler System Checkup provided by Oklahoma Drainage.
Sprinkler Systems need to be checked before winter to prevent pipes from freezing. Sprinkler Design determines whether sprinkler lines need to be bled. Emergency shut off valves also need to be checked and turned off for the winter.
In the Spring, all the water needs to be turned back on and all sprinkler zones and heads need to be tested.
Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair
Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.
Thousands of Sprinkler Heads have been adjusted.
Countless Sprinkler Controllers have been Reprogramed or Replaced.
We also have fixed a broken Sprinkler Pipe or Two. Seems like a million. Ok, not that many.
I wonder how many? A lot!!!!
Oklahoma Drainage and Sprinkler Repair provide Service for all of Central Oklahoma Including: Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.
Sprinkler Valves
Sprinkler Valve Replacement is a service that Oklahoma Drainage has provided Since 1993. Recently we removed 3 Rainbird Sprinkler Valves and replaced them with new ones. The valves had been crushed accidentally when a landscaper drove his truck across the yard.
Sprinkler System Check-Up in Edmond, Oklahoma City, Norman, and Moore.
Sprinkler System Check-Up process is very straightforward. We run through all the Sprinkler Zones one-at-a- time from the controller.
Sprinkler Controller
Sprinkler controllers can be a problem source. Many times, the wires in the controller are loose or have a “Short” in one of the wires. Sprinkler Programming can be a source of frustration. We can help with Programming your controller.
We check all the sprinkler heads in that zone and the valves as well.
Once the Sprinkler System Checkup is Complete, we provide a Quote for what it will cost to make the needed repairs.
Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps.
Providing Expert Sprinkler Repair – Broken Sprinkler Pipes – Sprinkler Head Adjustment – Sprinkler Valve Replacement
Servicing all of Central and Western Oklahoma since 1993. 405 203 9419
Sprinkler Valve Replacement is a service that Oklahoma Drainage has provided Since 1993. Recently we removed 3 Rainbird Sprinkler Valves and replaced them with new ones. The valves had been crushed accidentally when a landscaper drove his truck across the yard.
Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair
Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.
Thousands of Sprinkler Heads have been adjusted.
Countless Sprinkler Controllers have been Reprogramed or Replaced.
We also have fixed a broken Sprinkler Pipe or Two. Seems like a million. Ok, not that many.
I wonder how many? A lot!!!!
Oklahoma Drainage and Sprinkler Repair provide Service for all of Central Oklahoma Including: Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.
First Step
First, we dug up a good working area surrounding the broken Sprinkler Valves. Next, we cut out the broken valves and crushed PVC pipes. Finally, PVC pipe was cut and glued with new Sprinkler Valves following the original design and configuration. In this case the three original sprinkler valves were connected to each other inside one Valve Box.
We aren’t done yet though; two sprinkler wires must be connected to each Valve. One sprinkler wire is the “Common Ground.” The other wire is the power wire. All the sprinkler wiring is connected with water-proof wire connections.
The Common Ground wire and the Individual Power Wires all come from the Sprinkler Controller. Each Sprinkler Valve has its own power wire coming from the Controller. All the Sprinkler Valves are Connected to the Same Common Ground Wire.
Oklahoma City Sprinkler Repair
Before We Finish
Before dirt can be put back around the new valves, testing must be done. Each valve must be turned on, “one-at-a-time,” at the Controller to ensure good wire connection and functionality. Also, the Sprinkler Valves must be checked for leaks in the PVC Pipe.
Oklahoma Drainage and Sprinkler Repair provides Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties. We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.
Blanchard Sprinkler Repair has been provided by Oklahoma Drainage and Sprinkler Repair since 1993.
Sprinkler Controller Repair is a service provided by Oklahoma Drainage. A Sprinkler Controller is the “Brain,” of a Sprinkler System. They can wear out or stop working. Power surges in the home can cause damage to a controller.
Programming can be difficult for homeowners. We can help with programming or replace a Sprinkler Module if it is defective.
Start Time Programming
“Start Time” programing many times is confusing for homeowners. The definition of a Start Time is a time that is chosen for the sprinkler system to start watering. It causes zone 1 to start running. When zone 1 is finished it automatically stops and zone 2 begins. When Zone 2 is complete it stops and zone 3 begins. Simple enough Right! This continues until the last zone programed available runs.
The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on. This is not the case. They follow zone 1 which has the only Start Time programmed into the controller.
Be Careful with Multiple Start Times, just use One at first.
Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available. These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.
For Example, the first Start Time is set at 9Am. Zone 1 begins to run at 9am. When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on. By 10 am let’s say all the zones have run. Let’s say 8 hours later you have a second start time at 6 Pm. Zone 1 comes on and runs and by 7pm all the zones have run again. So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.
Here is the big problem! Some Homeowners believe the second start time is to start zone 2 running. They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4. No!!
So, this is how they program the controller. At 9am they have a start time and zone 1 starts. The homeowner programs a second start time at 9:10 am to mistakenly start zone 2. Nope! It starts zone 1 all over again. At 9:2o they have a 3rd start time for zone 3. Nope! It starts zone 1 for a third time. Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.
If Sprinkler Controller Programming is confusing? Make sure you only have One Start Time!
“Run Time,” is completed Next. It determines how long each zone runs. Zone One 10 Minutes, Zone Two, 15 Minutes, Zone Three 8 Minutes. You can set how long you want each zone to run.
French Drain Repair and Installation is a Central Focus for Oklahoma Drainage. We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.
Sprinkler Valve
A valve is an off or on switch for a particular Sprinkler Zone.
You might need a Sprinkler Valve replaced. Maybe it just needs to be adjusted? We can adjust the solenoid or “Bleed,” the valve itself. Debris might be stuck in it.
Oklahoma City Sprinkler Repair Replacing Valve
What Is a Sprinkler Valve?
Think of a Sprinkler Valve as an “Off or on” Switch. The Sprinkler Controller turns the valves on or off.
It Sends a signal through a wire which is underground to the sprinkler valve somewhere in your yard.
Once turned on, the valve lets water pass through a sprinkler pipe to a specific group of sprinkler heads called a Sprinkler Zone. The controller allows water to reach the sprinkler heads for a certain amount of time running through the sprinkler valve. Once the time is up, it shuts off the sprinkler valve and moves on to the next valve in sequence.
Think of it as walking into every room in your house one at a time. As you enter you turn on the light. As you leave you turn off the light and move to the next room. You are the controller. The light switch represents the sprinkler valve.
What causes a Sprinkler Valve to stop working?
Like anything else, a sprinkler valve can wear out. Sprinkler valves fail in closed position. It won’t run continuously if it breaks.
Sprinkler Valves get stuck while running sometimes. The water supply must be then turned off to stop the Sprinkler from running.
Sprinkler Valves can freeze and break in the winter if the sprinkler system has not been properly drained for winter’s cold.
(winterized)
Sprinkler Head Adjustment
Many homeowners need sprinkler heads moved to a new location or caped if they are no longer needed. A sprinkler head might be spraying in the wrong place.
Sprinkler Controllers also cause problems. Setting the programming might be difficult for the Homeowner. They can stop working correctly too.
Oklahoma Drainage can help with all of these problems and many others. The problems listed above are the most common.
Sprinkler Controller Repair is a service provided by Oklahoma Drainage. A Sprinkler Controller is the “Brain,” of a Sprinkler System. They can wear out or stop working. Power surges in the home can cause damage to a controller.
Programming can be difficult for homeowners. We can help with programming or replace a Sprinkler Module if it is defective.
Start Time Programming
“Start Time” programing many times is confusing for homeowners. The definition of a Start Time is a time that is chosen for the sprinkler system to start watering. It causes zone 1 to start running. When zone 1 is finished it automatically stops and zone 2 begins. When Zone 2 is complete it stops and zone 3 begins. Simple enough Right! This continues until the last zone programed available runs.
The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on. This is not the case. They follow zone 1 which has the only Start Time programmed into the controller.
Be Careful with Multiple Start Times, just use One at first.
Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available. These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.
For Example, the first Start Time is set at 9Am. Zone 1 begins to run at 9am. When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on. By 10 am let’s say all the zones have run. Let’s say 8 hours later you have a second start time at 6 Pm. Zone 1 comes on and runs and by 7pm all the zones have run again. So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.
The Big Problem
Here is the big problem! Some Homeowners believe the second start time is to start zone 2 running. They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4. No!!
So, this is how they program the controller. At 9am they have a start time and zone 1 starts. The homeowner programs a second start time at 9:10 am to mistakenly start zone 2. Nope! It starts zone 1 all over again. At 9:2o they have a 3rd start time for zone 3. Nope! It starts zone 1 for a third time. Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.
If Sprinkler Controller Programming is confusing? Make sure you only have One Start Time!
“Run Time,” is completed Next. It determines how long each zone runs. Zone One 10 Minutes, Zone Two, 15 Minutes, Zone Three 8 Minutes. You can set how long you want each zone to run.
French Drain Repair and Installation is a Central Focus for Oklahoma Drainage. We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.
Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps.
Providing Expert Sprinkler Repair – Broken Sprinkler Pipes – Sprinkler Head Adjustment – Sprinkler Valve Replacement
We provide Service for Folks in: Norman, Oklahoma City, Edmond, and Moore.
Central and Western Oklahoma is our Service Area since 1993.
(405) 203-9419
Oklahoma Drainage Installs Drainage Systems, and provides Expert Sprinkler System Repair.
Our Drainage Systems utilize French Drains, Surface Drains, Channel Drains, and Sump Pumps.
We Service all of Central Oklahoma including: Norman, Moore, Edmond, Yukon, Mustang, Oklahoma City, Midwest City, Del City, Blanchard, Newcastle, Purcell and Chickasha.
Back-Flow-Valve Service, Sprinkler Repair
Oklahoma Drainage and Sprinkler Repair Provides Service for Back-Flow-Valves and all types of Lawn Sprinkler Repair and Service. We have provided Expert Service for all of Central and Western Oklahoma Since 1993.
Back-Flow-Valves
There are two types of Back-Flow-Valves.
Above Ground
Above Ground Back-Flow-Valve.
Below Ground Back-Flow-Valve.
Below Ground Back-Flow-Valve
What is a Back-Flow-Valve?
A Back-Flow-Valve is a part of a Lawn Sprinkler System. Water passes through it from the water source which can be a Water Meter or a Well Pump. It forces water to travel in only one direction from the source to the sprinkler system. It can’t travel backward back to the water source which again is a water meter or well pump.
A Back-Flow-Valve provides protection to the water source from back pressure and chemical contamination from lawn fertilizer.
Most Cities require a Back-Flow-Valve as “Code” for Sprinkler Installation.
Emergency Shut off
Back-Flow-Valves usually have an Emergency Shutoff valve on them that can shut off the water to the lawn sprinkler system but keep the water turned on to the home. Most Back-Flow-Valves have two Emergency Shut off Handles. Either one will work. Many times, they are hard to turn, however.
If there is a leak or water is shooting up in the air just turn the valve handle and give us a call.
Blue Emergency Shutoff handles for a Back-Flow-Valve.
Norman Sprinkler Checkup is a Central Focus for Oklahoma Drainage. We Performed or first Sprinkler Repair in Norman in 1993. It was in Brookhaven on the West side of Norman.
Recently we had a customer in Oklahoma City who wanted to move his Sprinkler Valves. They were in a bad place in his flower bed. He wanted to plant a tree where the valves were located.
We moved 4 Sprinkler Valves about feet out into the yard. All the Sprinkler Pipes had to be redesigned and installed matching the new location and maintaining full functionality.
Oklahoma Drainage – We install French Drains, Channel Drains, Surface Drains, Sump Pumps and Sod.
If You live in Oklahoma City and water damaging your foundation, We can install a French Drain for you.
Or if you live in Norman and have water standing on your driveway, We can install a Channel Drain for you.
If you live in Edmond and have water flooding your basement, We can install a Sump Pump for you.
Or if you live in Moore and have water washing out your flower bed mulch, We can install a Surface Drain for you.
If you live in Yukon and need grass to grow we can install Sod too!
French Drain installation is a big focus for Oklahoma Drainage during our 30th year in business. A French Drain is one part of a Drainage System. A French Drain can be connected to other types of Drains or Gutter Downspouts and then run through Drainpipe to an Exit point where the water is released.
