Posts Tagged ‘Edmond Oklahoma Sprinkler Repair’

Sprinkler Repair Edmond Oklahoma. Oklahoma Drainage and Sprinkler Repair   has provided Expert Sprinkler Repair in Edmond since 1993.  Sprinkler Valves can have issues or leak.  Controllers have programming issues.  Sprinkler heads need to be adjusted or moved.  Sprinkler pipes break.  We can help with all of these things.

Recently in Edmond

Many times, Sprinkler heads get, “Out of Wack.”  Lawn mowers and weed eaters are notorious for this.  Sprinkler heads start spraying water in the wrong place.  It is frustrating to water concrete while plants and grass go without moisture.

Recently we had a customer who had sprinkler heads that were spraying out into the street more than they were hitting her yard.

The problem sprinkler head was out of adjustment.  The Rotor Sprinkler Head was turning too far to the right as it turned.  Water was spraying across the road and into the neighbor’s yard.

The Sprinkler Head Adjustment only took a few minutes.  Our customer then requested that we check the entire sprinkler system.  We started at Zone one and carefully put each zone through its Pases.

Sprinkler Controller Help

Sprinkler Controller

Edmond Sprinkler Repair

Sprinkler Controller Programming is sometimes difficult.

We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

The Mistake

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes, Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

 

Sprinkler Valve Replacement

Edmond Sprinkler Repair

 

Sprinkler Valves can Freeze in the winter and stop working.  They can be crushed by something heavy like a car driving across your yard.  Sprinkler Valves can just wear out too.  Unfortunately, when this occurs, they can get stuck in the “ON Position.”

Oklahoma Drainage and Sprinkler Repair have been installing and servicing Sprinkler Valves since 1993.

What Is a Sprinkler Valve?

Think of a Sprinkler Valve as an “Off or On” Switch.    The Sprinkler Controller   turns the valves on or off.

It Sends a signal through a wire which is underground to the sprinkler valve somewhere in your yard.

Once turned on, the valve lets water pass through a sprinkler pipe to a specific group of sprinkler heads called a Sprinkler Zone.  The controller allows water to reach the sprinkler heads for a certain amount of time running through the sprinkler valve.  Once the time is up, it shuts off the sprinkler valve and moves on to the next valve in sequence.

Think of it as walking into every room in your house one at a time.  As you enter you turn on the light.  As you leave you turn off the light and move to the next room. You are the controller.  The light switch represents the sprinkler valve.

What causes a Sprinkler Valve to stop working?

Like anything else, a sprinkler valve can wear out.   Sprinkler valves fail in closed position.  It won’t run continuously if it breaks.

Sprinkler Valves get stuck while running sometimes.   The water supply must be then turned off to stop the Sprinkler from running.

Sprinkler Valves can freeze and break in the winter if the sprinkler system has not been properly drained for winter’s cold.

(winterized)

Tree roots can twist or break sprinkler pipes running into sprinkler valves.  Magnolia Trees are really bad about this.  Oak trees can cause damage too.

Driving something heavy across your yard can crush sprinkler valves.  Usually riding lawnmowers don’t cause damage but any truck or car will if you drive over a valve.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provides Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

Emergency Sprinkler Repair

Sometimes things go wrong with sprinkler systems.

 

IF YOU NEED HELP IN THE MIDDLE OF THE NIGHT OR ON A WEEKEND WITH YOUR SPRINKLER SYSTEM, GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR.  405 203 9419

IT MAY TAKE A FEW HOURS FOR US TO GET THERE BUT WE WILL COME TO HELP.

Sprinkler Valve Replacement

Sprinkler Valve Replacement

One Common problem is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

 

Inside the valve box is a plastic handle that can turn off the water to the sprinkler system.  It can be blue or red or grey in color.

Many times, the valve box will be full of dirt, and you can’t turn or even see the handle until some of the dirt has been dug out by hand.

 

Water might be shooting up in the air somewhere on your property.

This can be caused by a broken sprinkler pipe or sprinkler valve.

Oklahoma Drainage Installs Drainage Systems,  and provides Expert Sprinkler System Repair.

Our Drainage Systems utilize French Drains, Surface Drains, Channel Drains, and Sump Pumps.  

We Service all of Central Oklahoma including: Norman, Moore, Edmond, Yukon, Mustang, Oklahoma City, Midwest City, Del City, Blanchard, Newcastle, Purcell and Chickasha.

Back-Flow-Valve Service, Sprinkler Repair

Oklahoma Drainage and Sprinkler Repair Provides Service for Back-Flow-Valves and all types of Lawn Sprinkler Repair and Service.  We have provided Expert Service for all of Central and Western Oklahoma Since 1993.

Back-Flow-Valves

There are two types of Back-Flow-Valves.

Above Ground

Above Ground Back-Flow-Valve

Above Ground Back-Flow-Valve.

 

Below Ground Back-Flow-Valve.

Below Ground Back-Flow-Valve

Below Ground Back-Flow-Valve

What is a Back-Flow-Valve?

A Back-Flow-Valve is a part of a Lawn Sprinkler System.  Water passes through it from the water source which can be a Water Meter or a Well Pump.  It forces water to travel in only one direction from the source to the sprinkler system.  It can’t travel backward back to the water source which again is a water meter or well pump.

A Back-Flow-Valve provides protection to the water source from back pressure and chemical contamination from lawn fertilizer.

Most Cities require a Back-Flow-Valve as “Code” for Sprinkler Installation.

Emergency Shut off

Back-Flow-Valves usually have an Emergency Shutoff valve on them that can shut off the water to the lawn sprinkler system but keep the water turned on to the home. Most Back-Flow-Valves have two Emergency Shut off Handles.  Either one will work.  Many times, they are hard to turn, however.

If there is a leak or water is shooting up in the air just turn the valve handle and give us a call.

In ground Back-Flow-Valve

Blue Emergency Shutoff handles for a Back-Flow-Valve.

Norman Sprinkler Checkup is a Central Focus for Oklahoma Drainage.  We Performed or first Sprinkler Repair in Norman in 1993.  It was in Brookhaven on the West side of Norman.

Recently we had a customer in Oklahoma City who wanted to move his Sprinkler Valves.  They were in a bad place in his flower bed.  He wanted to plant a tree where the valves were located.

We moved 4 Sprinkler Valves about feet out into the yard.  All the Sprinkler Pipes had to be redesigned and installed matching the new location and maintaining full functionality.

 

SHUT OFF THE SPRINKLER WATER IF YOU CAN AND GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR. SERVICING ALL OF CENTRAL AND WESTERN OKLAHOMA.

405 203 9419

Servicing Oklahoma City, Norman, Edmond and all of Central and Western Oklahoma

Oklahoma Drainage and Sprinkler Repair — Installing – French DrainsSurface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes Sprinkler Head Adjustment – Sprinkler Valve Replacement

We provide Service for Folks in: Norman, Oklahoma City, Edmond, and Moore.

Central and Western Oklahoma is our Service Area since 1993.  

                                                           (405) 203-9419

We rebuilt a Sprinkler System that hadn’t worked in years.  This took place in West Yukon.

We started with the Valves

The Sprinkler Valves were located in the back yard near the pool.  Six valves were located in one place.  They were very tightly connected in one Manifold.  None of the Sprinkler Valves had worked in a long time.  They were Toro Valves that were over 20 years old.  They all had to be replaced.

Surprisingly there was no shut-off valve for the Sprinkler Water.  The water had to be shut off at the Meter so we could install a Manual Shut off valve.  Once installed, the water was turned back on that ran to the house.   The water that ran to the Sprinkler System was shut off with our New Shut Off Valve.

Rainbird Sprinkler Valve

Edmond Sprinkler Repair is a big focus for Oklahoma Drainage and Sprinkler Repair.  We have been fixing broken sprinkler heads and Replacing Sprinkler Valves in Edmond since 1993.  Not only that, we service Sprinkler Controllers, find and fix leaks and do General Sprinkler Checkups.

405 203 9419

Recently in Edmond

Many times, Sprinkler heads get, “Out of Wack.”  Lawn mowers and weed eaters are notorious for this.  Sprinkler heads start spraying water in the wrong place.  It is frustrating to water concrete while plants and grass go without moisture.  Sprinkler Heads that are out of adjustment can spray out into the street or blast your front door.

Recently we had a customer who had sprinkler heads that were spraying out into the street more than they were hitting her yard.

The problem sprinkler head was out of adjustment.  The Rotor Sprinkler Head was turning too far to the right as it turned.  Water was spraying across the road and into the neighbor’s yard.

The Sprinkler Head Adjustment only took a few minutes.  Our customer then requested that we check the entire sprinkler system.  We started at Zone one and carefully put each zone through its Paces.

Sprinkler Controller Help

Sprinkler Controller

Edmond Sprinkler Repair

Sprinkler Controller Programming is sometimes difficult.

We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times,  just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

Sprinkler Controller

Sprinkler Controller

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

The Mistake

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes, Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

 

We rebuilt a Sprinkler System that hadn’t worked in years.  This took place in West Yukon.

Sprinkler Head Replacement

Sprinkler Head Replacement

We started with the Valves

The Sprinkler Valves were located in the back yard near the pool.  Six valves were located in one place.  They were very tightly connected in one Manifold.  None of the Sprinkler Valves had worked in a long time.  They were Toro Valves that were over 20 years old.  They all had to be replaced.

Surprisingly there was no shut-off valve for the Sprinkler Water.  The water had to be shut off at the Meter so we could install a Manual Shut off valve.  Once installed, the water was turned back on that ran to the house.   The water that ran to the Sprinkler System was shut off with our New Shut Off Valve.

The Sprinkler Valves Were Removed

Now, the 6 valves had to replaced.  The valves that were used were made by Rain Bird.  Before we began, I had to talk to the Customer.  The previous valve design was a bad idea to repeat.

The original Sprinkler Valves were crammed into one large valve box in one very tight manifold.  This is bad because the valves were too close to the fittings.  Simply put, if one valve had to be replaced or worked on in the future, all 6 valves had to be taken out and replaced.   If one valve was bad and 5 worked fine, they all still had to be replaced.

That’s Stupid!

I recommended that an additional Valve Box be installed putting 3 valves in each Valve Box.  This would allow plenty of space between the valve fittings.  If one Sprinkler Valve had to be adjusted or replaced in the future, the other 5 valves need not be disturbed.  Simple Enough!

Check For Leaks

Once the valves were replaced and working, it was time to turn on each Sprinkler Zone, one at a time.  Water was shooting up from the ground in several places in zone 1.  Two broken Sprinkler Pipes and 5 bad Sprinkler Heads in zone 1 had to be fixed and replaced.  We went through each of the 6 zones in similar fashion fixing lots of leaks and replacing bad sprinkler heads.

One Common problem

is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Emergency Shutoff Valve

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

Back-Flow-Valve Service, Sprinkler Repair

Oklahoma Drainage and Sprinkler Repair Provides Service for Back-Flow-Valves and all types of Lawn Sprinkler Repair and Service.  We have provided Expert Service for all of Central and Western Oklahoma Since 1993.

Back-Flow-Valves

There are two types of Back-Flow-Valves.

Note! Some Lawn Sprinkler Systems will have no Back-flow Valve at all.  Most Systems do, but the System can function without it.

Above Ground

 

Below Ground Back-Flow-Valve.

Below Ground Back-Flow-Valve

Below Ground Back-Flow-Valve

What is a Back-Flow-Valve?

A Back-Flow-Valve is a part of a Lawn Sprinkler System.  Water passes through it from the water source which can be a Water Meter or a Well Pump.  It forces water to travel in only one direction from the source to the sprinkler system.  It can’t travel backward back to the water source which again is a water meter or well pump.

A Back-Flow-Valve provides protection to the water source from back pressure and chemical contamination from lawn fertilizer.

Most Cities require a Back-Flow-Valve as “Code” for Sprinkler Installation.

Emergency Shut off

Back-Flow-Valves usually have an Emergency Shutoff valve on them that can shut off the water to the lawn sprinkler system but keep the water turned on to the home. Most Back-Flow-Valves have two Emergency Shut off Handles.  Either one will work.  Many times, they are hard to turn, however.

If there is a leak or water is shooting up in the air just turn the valve handle and give us a call.

 

 

Inside the valve box is a plastic handle that can turn off the water to the sprinkler system.  It can be blue or red or grey in color.

Many times, the valve box will be full of dirt, and you can’t turn or even see the handle until some of the dirt has been dug out by hand.

 

Water might be shooting up in the air somewhere on your property.  This can be caused by a broken sprinkler pipe or sprinkler valve.

SHUT OFF THE SPRINKLER WATER IF YOU CAN AND GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR. SERVICING ALL OF CENTRAL AND WESTERN OKLAHOMA.

405 203 9419

Servicing Oklahoma City, Norman, Edmond and all of Central and Western Oklahoma

The Sprinkler Repair Cost About Half of the Cost of Completely New System.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provide Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

Oh! we also solve water problems and provide Drainage.

Oklahoma Drainage – We install French Drains, Channel Drains, Surface Drains, Sump Pumps and Sod.

If You live in Oklahoma City and water damaging your foundation, We can install a French Drain for you.

Or,If you live in Norman and have water standing on your driveway, consider a Channel Drain Installation.

If you live in Edmond and have water flooding your basement, a Sump Pump can help.

Or, you live in Moore and have water washing out your flower bed mulch, We can install a Surface Drain for you.

If you live in Yukon and need grass to grow, we can install Sod too!

Installing Drain Pipe from French Drain in Back Yard

Installing Drainpipe from French Drain in Back Yard

Do you have water standing in your yard after a heavy rain?  Do your gutters turn your sidewalk into a moat after a storm.  Worst of all, do you have water seeping into your home or business from Storm-Water runoff?

 

Installing Solid 4 Inch Drain Pipe Between French Drain and Curb

Installing Solid 4 Inch Drainpipe Between French Drain and Curb

Oklahoma Drainage can help with these and many other “standing water” and ” Drainage Problems. We can diagnose your drainage problem and design a drainage system to fit your specific needs.  In Business since 1993.  

We utilize: French Drains, Surface Drains, Channel Drains, Basin Drains, Trench Drains, Basement Drains, and Sump Pumps.

 

We service all of Central and Western Oklahoma

 

 

Edmond Oklahoma Sprinkler Repair

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR – Servicing Central and Western Oklahoma since 1993.

Sprinkler Repair French Drain InstallationDrainage System Installation

This week Oklahoma Drainage and Sprinkler Repair overhauled a flowerbed Sprinkler Zone in a Sprinkler System in East Edmond.

The homeowner had an existing Sprinkler System that was in good shape for the most part but had problems with the flowerbed Sprinkler Zone.  It had a Drip Sprinkler Zone installed.  The Drip Sprinkler System was installed correctly but was not practical for the flower bed.

The flowerbed was very sandy and could not retain water very well even with good mulch.  Plus, the surrounding brick walls increased the amount of heat the plants had to endure in the summer.  The Drip Sprinkler Zone could not provide enough water fast enough for the plants.

To solve the problem, we took out the Drip Sprinkler Zone and replaced it with a traditional “Pop-Up Sprinkler Zone.”

Problem solved.

Edmond Sprinkler Repair is a big focus for Oklahoma Drainage and Sprinkler Repair.  We have been fixing broken sprinkler heads and Replacing Sprinkler Valves in Edmond since 1993.  Not only that, we service Sprinkler Controllers, find and fix leaks and do General Sprinkler Checkups.

Recently in Edmond

Many times, Sprinkler heads get, “Out of Wack.”  Lawn mowers and weed eaters are notorious for this.  Sprinkler heads start spraying water in the wrong place.  It is frustrating to water concrete while plants and grass go without moisture.

Recently we had a customer who had sprinkler heads that were spraying out into the street more than they were hitting her yard.

The problem sprinkler head was out of adjustment.  The Rotor Sprinkler Head was turning too far to the right as it turned.  Water was spraying across the road and into the neighbor’s yard.

The Sprinkler Head Adjustment only took a few minutes.  Our customer then requested that we check the entire sprinkler system.  We started at Zone one and carefully put each zone through its Pases.

Sprinkler Controller Help

Sprinkler Controller

Edmond Sprinkler Repair

Sprinkler Controller Programming is sometimes difficult.

We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

The Mistake

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes, Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

 

Sprinkler Valve Replacement

Edmond Sprinkler Repair

We rebuilt a Sprinkler System that hadn’t worked in years.  This took place in West Yukon.

We started with the Valves

The Sprinkler Valves were located in the back yard near the pool.  Six valves were located in one place.  They were very tightly connected in one Manifold.  None of the Sprinkler Valves had worked in a long time.  They were Toro Valves that were over 20 years old.  They all had to be replaced.

Surprisingly there was no shut-off valve for the Sprinkler Water.  The water had to be shut off at the Meter so we could install a Manual Shut off valve.  Once installed, the water was turned back on that ran to the house.   The water that ran to the Sprinkler System was shut off with our New Shut Off Valve.

We provide:

1.  Sprinkler Valve Problems

2.  Sprinkler Wiring Problems

3.  Sprinkler Controller Problems / Sprinkler Clock Problems

4.  Sprinkler Head Problems

5.  Sprinkler Pipe Problems

6.  Sprinkler Coverage Problems

7.  Sprinkler Redesign Problems for new fences or swimming pools.

If you have water running down the street in the middle of the night because your sprinkler system is leaking or won’t shut off, give Oklahoma Drainage and Sprinkler Repair a call.  405 203 9419

 

Sprinkler Repair is a central focus for Oklahoma Drainage and Sprinkler Repair.  Just like any car or home, a lawn sprinkler system must be updated and maintained.  Typically, people wait till spring to get the kinks worked out of their sprinkler system.

 

I can tell you this, DON’T WAIT TILL MARCH TO GET YOUR SPRINKLER SYSTEM IN SHAPE.  BY APRIL THERE WILL BE A FLOOD OF PEOPLE TRYING TO GET BROKEN SPRINKLER HEADS FIXED OR NEW SPRINKLER CONTROLLERS INSTALLED OR LEAKING BACK-FLOW VALVES REPLACED.

CONSIDER GETTING YOUR SPRINKLER REPAIR WORK DONE ANY TIME OTHER THAN THE SPRING.  FOR THOSE OF YOU WHO HAVE NO CHOICE AND MUST HAVE WORK DONE IN THE SPRING, SCHEDULE AS EARLY AS YOU CAN.

OUR SPRINKLER REPAIR WORK IS TOP QUALITY AND OUR PRICES ARE FAIR.  IT IS OUR GOAL TO GET TO CUSTOMERS QUICKLY IN MARCH AND APRIL, WHILE MAINTAINING OUR QUALITY OF WORK.

 

Oklahoma Drainage and Sprinkler Repair can help if you need to re-design your Sprinkler System.  If for example you are adding a swimming pool in your back yard, we can move the Sprinkler Heads and Sprinkler Pipes to fit the new dimensions of your yard.  We can redesign or add-on to sprinkler systems where the homeowners needs change.

Maybe you don’t need a large part of your sprinkler system redesigned.  You May just want a few heads moved to new locations.

Whatever your Sprinkler needs may be, Oklahoma Drainage and Sprinkler Repair can help.  Give us a call at : 405 203 9419

 

Sprinkler Repair for us is very clear.  We have been doing it a long time and have become very good at it.  Many times, we get called in to handle tough problems that the initial Sprinkler Company couldn’t handle.