Oklahoma Drainage and Sprinkler Repair – 405 203 9419

French Drain for Flood Control.  Sometimes French Drains are installed to control flooding.  Many times, areas can flood that have drains already installed.  As a general rule, a French Drain can take water into the drainpipe faster than a Surface Drain if installed correctly.

French Drain

Oklahoma Drainage  — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps

If you have water causing damage to your home or business, we can help!  Oklahoma Drainage has been solving drainage and water problems since 1993.  If you have water standing in your yard or it’s leaking into your AC ducts, we can help.

 

Servicing all of Central and Western Oklahoma since 1993.

French Drain Installation

Oklahoma Drainage and Sprinkler Repair has been diagnosing and solving Drainage Problems since 1993.  Water has the ability to get into places around your home where you really don’t want it to be.  Some drainage problems are easy to solve.

Typically, water enters the problem drainage area one way from one source.  The really tricky drainage problems occur when water enters the problem drainage area from multiple directions and from multiple sources.  Sometimes a secondary water source can’t be seen or identified until the primary water problem source is eliminated.

An example of this occurs when water is running into a problem area, in an obvious way, over the ground where you can see it.

Simple enough.

A drainage system is installed with a surface drain as the “intake” with drainage pipe running to an exit point.  Initially the water drains away and everything looks great.  The next day water is back and is all around the surface drain, but below the edge and it hasn’t rained at all, so no additional water ran over the surface of the ground to flood the area.  The primary water source was solved, ( The surface water run off ) but the secondary water source was not.  Which was sub-surface water, (ground water) running into the area.

Surface Drain Limitations

A surface drain can’t drain “ground water.”  A French Drain should have initially been installed instead of a Surface Drain.  A French Drain can drain both Surface Water and Ground Water All Drainage Systems and French Drains as well need a place to take the water to.  This is called an Exit Point.  We use two types of Exits.  The first is a curb outlet.  We cut the curb with a concrete saw and install a rectangular curb outlet set in acrylic concrete.

A rectangular outlet is superior to a round one.  Air travels back up the pipe through the top two corners to allow a more continuous water flow.  If you have ever poured liquid out of a 2 liter bottle turning it completely upside down, you will see that it drains but not very well.

Oklahoma Drainage installs a variety of other types of Drains.  Our Drainage Systems may utilize: French Drains, Surface Drains, Channel Drains, Trench Drains, Basin Drains, and Sump Pumps.  In the past 31 years, we have installed French Drains to keep water away from home and business foundations,

Surface Drains to keep water away from sidewalks and driveways, Trench Drains, and French Drains to keep standing water out of flowerbeds and yards, and Sump Pumps to remove water from basements and outdoor low-lying areas.

Drainage Problems

Wow, Some Drainage Problems are tougher than others.  Had a customer in Chickasha with an unusual Drainage Problem.  She had a new Driveway installed.  The Cement work was nice enough but they left out one major consideration when installing the new Driveway.  Even after a small rain the water would run right down the driveway, under the Garage Door and directly into the Garage.

This was a bad problem that was about to get worse.  The first big rain came and everything was magnified.  The Rushing water took out the garage door and the back wall of the garage.  Yikes!!

Hmm, What to do?  The company that installed the Driveway was nowhere to be found.  No surprise.

The water volume was huge, and the customer had no means to redo the driveway which was substantial.

WHERE WE HAVE WORKED!

In 1993 we had no website.  I stuck little signs on the side of the road as advertisement.  I got my first Drain Installation work in March of 1993 in Norman.  It was in Brookhaven North of Robinson Street on the West side of I 35.

Over the years Oklahoma Drainage and Sprinkler Repair has installed all types of Drainage Systems in almost Every town in Central and Western Oklahoma.

The majority of our customers live in Oklahoma City, Norman, Edmond, Yukon, Mustang, Moore, Midwest City, Del City, Blanchard, New Castle, Yukon and Choctaw.

Oklahoma Drainage and Sprinkler Repair hasn’t been limited to those areas, however.  We have also installed French Drains, Surface Drains, Channel Drains, and Sump Pumps in many other cities.

Working Drainage Systems Installed by Oklahoma Drainage also reside in: Lawton, Duncan, Ardmore, Chickasha, Shawnee, Enid, Weatherford, Elk City, El reno and many other places.

If you live in any of these Cities or towns, we have installed a French Drain, Surface Drain, Channel Drain, or Sump Pump within 5 miles of your home.

Here is a description of other recent work.

A little bit North of Downtown Oklahoma City, Oklahoma Drainage installed a 6-inch French Drain between two businesses which were less than three feet apart.  The French Drain went between a Law Firm and a Tire shop.  Water was leaking through the walls of both businesses.  Gutters between the two establishments were dumping a huge amount of water.  We installed a 6-inch French Drain between the gutters.

It took a long time to get the dirt out of the trench for the French Drain.  It was a very tight fit.  We had to use a little red wagon to haul out the dirt for the French Drain and haul back in the crushed limestone for the French Drain.  It looked a little silly, but it was the only thing we could find that was narrow enough to fit between the buildings.  A French Drain that normally would take 1 day to install took three.

Sprinkler Repair Facts

 

Oklahoma Drainage and Sprinkler Repair provides Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

Emergency Sprinkler Repair

Sometimes things go wrong with sprinkler systems.

 

IF YOU NEED HELP IN THE MIDDLE OF THE NIGHT OR ON A WEEKEND WITH YOUR SPRINKLER SYSTEM, GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR.  405 203 9419

IT MAY TAKE A FEW HOURS FOR US TO GET THERE BUT WE WILL COME TO HELP.

 

One Common problem is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

 

Inside the valve box is a plastic handle that can turn off the water to the sprinkler system.  It can be blue or red or grey in color.

Many times, the valve box will be full of dirt, and you can’t turn or even see the handle until some of the dirt has been dug out by hand.

 

Water might be shooting up in the air somewhere on your property.  This can be caused by a broken sprinkler pipe or sprinkler valve.

SHUT OFF THE SPRINKLER WATER IF YOU CAN AND GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR. SERVICING ALL OF CENTRAL AND WESTERN OKLAHOMA.

405 203 9419

Servicing Oklahoma City, Norman, Edmond and all of Central and Western Oklahoma

 

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,     Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

We started with the Valves

The Sprinkler Valves were located in the back yard near the pool.  Six valves were located in one place.  They were very tightly connected in one Manifold.  None of the Sprinkler Valves had worked in a long time.  They were Toro Valves that were over 20 years old.  They all had to be replaced.

Surprisingly there was no shut-off valve for the Sprinkler Water.  The water had to be shut off at the Meter so we could install a Manual Shut off valve.  Once installed, the water was turned back on that ran to the house.   The water that ran to the Sprinkler System was shut off with our New Shut Off Valve.

The Sprinkler Valves Were Removed

Now, the 6 valves had to replaced.  The valves that were used were made by Rain Bird.  Before we began, I had to talk to the Customer.  The previous valve design was a bad idea to repeat.

The original Sprinkler Valves were crammed into one large valve box in one very tight manifold.  This is bad because the valves were too close to the fittings.  Simply put, if one valve had to be replaced or worked on in the future, all 6 valves had to be taken out and replaced.   If one valve was bad and 5 worked fine, they all still had to be replaced.

That’s Stupid!

I recommended that an additional Valve Box be installed putting 3 valves in each Valve Box.  This would allow plenty of space between the valve fittings.  If one Sprinkler Valve had to be adjusted or replaced in the future, the other 5 valves need not be disturbed.  Simple Enough!

Check For Leaks

Once the valves were replaced and working, it was time to turn on each Sprinkler Zone, one at a time.  Water was shooting up from the ground in several places in zone 1.  Two broken Sprinkler Pipes and 5 bad Sprinkler Heads in zone 1 had to be fixed and replaced.  We went through each of the 6 zones in similar fashion fixing lots of leaks and replacing bad sprinkler heads.

The Sprinkler Repair Cost About Half of the Cost of Completely New System.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

Sprinkler Head Adjustment is a service provided by Oklahoma Drainage and Sprinkler Repair.  We have adjusted sprinkler heads since 1993.

Many times, Sprinkler heads get, “Out of Wack.”  Lawn mowers and weed eaters are notorious for this.  Sprinkler heads start spraying water in the wrong place.  It is frustrating to water concrete while plants and grass go without moisture.

Pop-Up Sprinkler Heads

Pop-Up Sprinkler Heads can be adjusted several ways.  How far water goes to the left or right can be increased or decreased.  The distance the water goes can also be increased or decreased.  Finally, how high a sprinkler head pops up can be increased or decreased by installing a taller or shorter head.

Sometimes sprinkler heads spray a reduced distance and don’t perform very well due to water scale.  Minerals in the water can completely clog a Pop-Up.  Usually, the sprinkler nozzle on top of the sprinkler head, need only be replaced without replacing the entire head.

Rotor Sprinkler Heads also can be adjusted to the left or right.  Spray Distance can be increased or decreased as well.

Needs Change

What’s going on in your yard can change.  This calls for Sprinkler Head Adjustment.  Adding or removing a swimming pool changes everything concerning sprinkler heads.  Any number of things can change the necessary sprinkler head coverage.

 

 

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes – Sprinkler Head Adjustment – Sprinkler Valve Replacement

We provide Service for Folks in: Norman, Oklahoma City, Edmond, and Moore.

Central and Western Oklahoma is our Service Area since 1993.  

                                                           (405) 203-9419

Check out Sprinkler System Check-Up