Posts Tagged ‘edmond sprinkler repair’

New French Drain Installed in Edmond, Sprinkler Repair

Posted: February 27, 2023 in Edmond Oklahoma French Drain Installation, french drain, sprinkler repair, sprinkler repair contractor, Sprinkler Repair Service
Tags: , ,
9

Edmond French Drain Installation is a central focus for Oklahoma Drainage.  We have provided service for over 1200 customers in Edmond since 1993.

French Drain, Edmond, Oklahoma City, Norman and Moore.

Oklahoma Drainage – 405 203 9419 — Servicing all of Central and Western Oklahoma

 

Our Drainage Systems utilize French Drains, Surface Drains, Channel Drains, and Sump Pumps.   With over 25 years of experience we provide top quality French Drains, Drainage Systems. 

French Drain in Oklahoma City

French Drain in Oklahoma City

Just what is a “French Drain?” Many times people incorrectly

French Drain Installation

French drain Installation
with trench liner and pipe filter

 

A French Drain can protect your foundation!

use the phrase, “French Drain,” when they mean “Surface Drain” or “Channel Drain.”

Installing French Drain

A basic French Drain consists of a Perforated Drain Pipe in the bottom of a trench. The French Drain Trench runs through a Problem Drainage Area that needs to be drained.   The French Drain Pipe is perforated (Full of Small Holes) and has Neo-Prene Soc around the pipe.  This soc helps prevent debris from clogging the French Drain Pipe.

The dirt that was taken out to make the trench is hauled away. It is replaced by some type of small stone or gravel depending on what is desired or available. I prefer crushed 1 inch limestone. It is the most economical option in my area. Pea Gravel or some other type of small stone can work just as well. The limestone or gravel is placed in the trench on top of the perforated Drain Pipe and filled all the way to the surface (ground level).

Sandy Soil

In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drain Pipe or the Gravel are installed. This helps maintain the integrity of the trench over time. It also increases the cost of the French Drain and the amount of time to install it. I install a trench liner in a French Drain about 20% of the time. Most of the time a liner in not needed.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provides Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

Edmond Channel Drain Installation, Sprinkler Repair Lawton, Norman, Oklahoma City, Midwest City.

Posted: February 1, 2020 in Edmond Channel Drain, Edmond Channel Drain Installation, Edmond Oklahoma French Drain, edmond sprinkler repair, french drain
Tags: ,
3

Edmond Channel Drain installation is a Central focus for Oklahoma Drainage.  We also provide Expert Sprinkler Repair.

Channel Drain Installed in Ardmore

Patio Channel Drain Installation in Edmond

NDS Grey Composite Channel Drain Running Across Driveway Connected to 4 Inch ADS Solid Drain Pipe

NDS Grey Channel Drain Running Across Driveway
in Edmond

 

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provides Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

Oklahoma Drainage –     We install French Drains, Channel Drains, Surface Drains, Sump Pumps and Sod.

If You live in Oklahoma City and water damaging your foundation, We can install a French Drain for you.

If you live in Norman and have water standing on your driveway, We can install a Channel Drain for you.

If you live in Edmond and have water flooding your basement, We can install a Sump Pump for you.

If you live in Moore and have water washing out your flower bed mulch, We can install a Surface Drain for you.

If you live in Yukon and need grass to grow we can install Sod too!

Oklahoma Drainage and Sprinkler Repair: Servicing all of Central and Western Oklahoma since 1993.

Standing Water on Your Driveway?  A Surface Drain set in concrete may be what you need. Or maybe you need a French Drain Running alongside your driveway instead.  Handling water problems is what we are good at.  If you need help, Oklahoma Drainage can provide the best solution for your unwanted water problems.

standing water

A good place for a French Drain

French Drain protects sidewalk

French Drain keeps water off of sidewalk

We just finished a 4 inch Drainage System in Yukon.  It was a complicated system to install.  It utilized 4 inch French Drain in the flower beds,  12 inch Surface Drains on the side of the house,  6 inch French Drain along the garage foundation with 2 Pop – Up Emitters in the back yard and 3 Curb Fittings in the front.    First we installed 4 inch French Drain in the flowerbeds on both sides of the front door.  We connected 4 inch solid Drain Pipe into the French Drain and ran them underside walk to the curb.  Next we cut the curb with a concrete saw and installed 3 curb outlets for 3 separate French Drains.

Next we installed 4 12 Inch Drain Basins with grates along both sides of the house continuing with Solid Drain Pipe to the Pop-Up Emitters on the back fence. Finally we completed the Drainage System by installing a long run of 6 inch French Drain down the side of the garage foundation.   Installing the French Drains in the flower beds was the most difficult and took the most time.  Each French Drain took over a ton of crushed limestone to fill the French Drain trench.  The Six inch French Drain took even more limestone.

 Oklahoma Drainage and Sprinkler Repair –

Hey Oklahoma, We are expanding to service all of Western Oklahoma as well as Central Oklahoma.  If you live in Elk City, and need a French Drain, we can help.  If water is standing on your driveway in Clinton, Give us a call.  Duncan, Lawton, and Altus are all new areas of service for us.

Since 1993 Oklahoma Drainage and Sprinkler Repair has solved all types of standing water and drainage issues.  We install Drainage Systems that utilize French Drains, Surface, Drains, Channel Drains, and Sump Pumps depending on the customers needs.

If you have water in the wrong place , we can help!

We also have Decades of experience repairing all types of Lawn Sprinkler Problems.  Fixing broken sprinkler heads, sprinkler valve problems and controller trouble just to name a few things.

French Drains as part of a Drainage System – 

cutting concrete for channel drain

Cutting Driveway for Channel Drain

Many times people use the term ” French Drain” as general name for a Drain used in or around your home.  French Drains are designed to move a lot of water over a large flooded area.  They are also designed to take water in on the surface of the ground or below the surface of the ground.  This is very important if the water coming into the flooded area is moving through the ground or coming up from underneath.  ” Sub Surface Water Movement.”  The picture below is not a French Drain!

A French Drain looks like this

river rock french drain

A French Drain Can Handle Standing Water

French Drain or Surface Drain

A French Drain can take in water in a broad area.  It can move a much larger volume of water compared to a Surface Drain.  Also, it can move sub surface water moving into the area where a Surface Drain won’t move any water at all.

Surface Drains are designed to move surface water only on a smaller scale in confined areas.

Each solves specific drainage problems.  A Drainage System may use one or both together or even several using many types of drains.

Do you have standing water in a large area in your yard?  Typically this calls for a French Drain.  A French Drain is a great way to control standing water in a large grassy area.  It can also protect areas from flooding to a certain degree.  As long as the French Drains capacity to move water is not exceeded.  If the French Drains capacity is exceeded then water will stand in the drainage area until the rain stops and the drain has time to catch up.  A good way to prevent this is to install a bigger French Drain with a larger pipe.  The difference between a 3 inch French Drain and a 6 inch French Drain is huge.

Another way to beef up a French Drain is to connect gutter down spouts in front of the French Drain.  The water coming off the roof causes suction in the French Drain Behind it.  This greatly increases the French Drains ability to move water without increasing the size of the French Drain Pipe.

New French Drain

New French Drain

French Drain Installation In Yukon

Oklahoma Drainage and Sprinkler Repair : Servicing all of Central and Western Oklahoma since 1993.

Standing Water on Your Driveway?  A Surface Drain set in concrete may be what you need. Or maybe you need a French Drain Running alongside your driveway instead.  Handling water problems is what we are good at.  If you need help, Oklahoma Drainage can provide the best solution for your unwanted water problems.

standing water

A good place for a French Drain

We just finished a 4 inch Drainage System in Yukon.  It was a complicated system to install.  It utilized 4 inch French Drain in the flower beds,  12 inch Surface Drains on the side of the house,  6 inch French Drain along the garage foundation with 2 Pop – Up Emitters in the back yard and 3 Curb Fittings in the front.    First we installed 4 inch French Drain in the flowerbeds on both sides of the front door.  We connected 4 inch solid Drain Pipe into the French Drain and ran them underside walk to the curb.  Next we cut the curb with a concrete saw and installed 3 curb outlets for 3 separate French Drains.

Next we installed 4 12 Inch Drain Basins with grates along both sides of the house continuing with Solid Drain Pipe to the Pop-Up Emitters on the back fence. Finally, we completed the Drainage System by installing a long run of 6 inch French Drain down the side of the garage foundation.   Installing the French Drains in the flower beds was the most difficult and took the most time.  Each French Drain took over a ton of crushed limestone to fill the French Drain trench.  The Six-inch French Drain took even more limestone.

 Oklahoma Drainage

Hey Oklahoma, we are expanding to service all of Western Oklahoma as well as Central Oklahoma.  If you live in Elk City, and need a French Drain, we can help.  If water is standing on your driveway in Clinton, Give us a call.  Duncan, Lawton, and Altus are all new areas of service for us.

Since 1993 Oklahoma Drainage and Sprinkler Repair has solved all types of standing water and drainage issues.  We install Drainage Systems that utilize French Drains, Surface, Drains, Channel Drains, and Sump Pumps depending on the customers needs.

If you have water in the wrong place, we can help!

 

French Drains as part of a Drainage System – 

Many times people use the term ” French Drain” as general name for a Drain used in or around your home.  French Drains are designed to move a lot of water over a large flooded area.  They are also designed to take water in on the surface of the ground or below the surface of the ground.  This is very important if the water coming into the flooded area is moving through the ground or coming up from underneath.  ” Sub Surface Water Movement.”  The picture below is not a French Drain!

A French Drain looks like this

A French Drain can take in water in a broad area.  It can move a much larger volume of water compared to a Surface Drain.  Also, it can move sub surface water moving into the area where a Surface Drain won’t move any water at all.

Surface Drains are designed to move surface water only on a smaller scale in confined areas.

Each solves specific drainage problems.  A Drainage System may use one or both together or even several using many types of drains.

Do you have standing water in a large area in your yard?  Typically this calls for a French Drain.  A French Drain is a great way to control standing water in a large grassy area.  It can also protect areas from flooding to a certain degree.  As long as the French Drains capacity to move water is not exceeded.  If the French Drains capacity is exceeded then water will stand in the drainage area until the rain stops and the drain has time to catch up.  A good way to prevent this is to install a bigger French Drain with a larger pipe.  The difference between a 3 inch French Drain and a 6 inch French Drain is huge.

Another way to beef up a French Drain is to connect gutter down spouts in front of the French Drain.  The water coming off the roof causes suction in the French Drain Behind it.  This greatly increases the French Drains ability to move water without increasing the size of the French Drain Pipe.

gutter connect to drain

Gutter Downspout Connected to 6 Inch French Drain

Recently we installed a French Drain inside the court yard of a rest home in Norman.  We had several interesting challenges to overcome that were not typical for a French Drain Installation.  The court yard was in the center of the home and was a secure area for the patrons.  We had to put down painters tarps to run our wheel barrows over.  We took out 44 loads of dirt and brought in 52 loads of Crushed one inch lime stone for the French Drain.  Each trip was over a hundred yards from the trailer in the parking lot, in the front door, down the hall, making two turns along the way.  Each time we had to be escorted by security.  Needless to say, the installation of this particular drainage system took a while.In the above picture, the French Drain runs along the low area crossing all the areas where water would stand each time it rained.

Rest home french drain

French Drain in Rest Home Courtyard

When a French Drain is installed, a big mistake that is made by many people is to cover up the gravel with dirt.  This is a big mistake.  Basically it is ” Putting the cork back in the bottle.”  If the French Drain is in full sun and has a type of grass surrounding it that spreads on its own such a ” Tift” or “Bermuda” , Grass will grow over it and the French Drain will eventually disappear.  Grass covering a French Drain is a good thing if it grows across the drain without adding dirt.  The Grass thatch acts a water filter preventing clogging and extending the life of the Drainage System.

When a French Drain is in Full Shade, or the surrounding grass will not spread on its own, such as with Fescue,  other steps must be taken.  One option is to just leave it alone.  If you don’t mind how it looks, it will drain a large amount of water for many years.  Many times a French Drain can be a landscaping focal point.  They can be dressed up with all kinds of Rocks and Stones and Plants.

 

Just what is a “French Drain?”  Many times people incorrectly

French drain installed
A French Drain can protect your foundation!

use the phrase, “French Drain,”  to apply to many different types of Drains that could be used in a Drainage System.  The term is widely used and many times incorrectly connected to “Surface Drains,” or “Channel Drains.”

A Surface Drain has a grate that sits on top of a basin.  The basin is underground.  A Drain Pipe is connected underground to an outlet on the Drain Basin.  Storm-Water Drains through the grate into the Drain Basin.  Once in the Drain Basin, water travels out of the basin through a Drain Pipe.  The Storm-Water continues downhill in an underground Drain Pipe to an exit point.

THIS IS NOT A FRENCH DRAIN!

A Surface Drain may come in many different shapes or sizes.  The Drain Grate may be round or square.  Here is a picture of a common Surface Drain.

A Channel Drain is a type of Surface Drain and many times is installed in concrete across sidewalks or driveways.

channel drain driveway
Edmond Channel Drain Installation

A French Drain is completely different from a Surface Drain.  A basic French Drain consists of a Perforated Drain Pipe in the bottom of a trench.  The Drain Pipe should have a neoprene sock around the Perforated Drain Pipe.   This is to ensure that the Drain Pipe does not become clogged.

The dirt that was taken out to make the trench is hauled away.  It is replaced by some type of small stone or gravel depending on what is desired or available.  I prefer crushed 1 inch lime stone.  It is the most economical option in my area.  Pea Gravel or some other type of small stone can work just as well.    The lime-stone or gravel is placed in the trench on top of the perforated Drain Pipe and filled all the way to the surface (ground level).   In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drain Pipe or the Gravel are installed.  This helps maintain the integrity of the trench over time.  It also increases the cost of the French Drain and the amount of time to install it.  I install a trench liner in a French Drain about 20% of the time.  Most of the time a liner in not needed.

A French Drain is designed to handle a large volume of water and cover a large area. The Drain is anyplace the trench goes. It has many applications and can be used in many situations.  It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Down-Spouts connected to it.
The main downfall of a French Drain is that they, for the most part aren’t very pretty.  They don’t look very nice in a yard once they are completed.
Depending on the area the French Drain is installed and the type of grass around the French Drain, will dictate whether grass grows over the lime stone.  Grass can grow up and through the gravel in the French Drain over time eventually covering the gravel.  This is Ok.  It won’t have a measurable effect on the performance of the drain.
DONT COVER THE GRAVEL IN THE FRENCH DRAIN WITH DIRT.  THE FRENCH DRAIN WON’T WORK IF THE TRENCH IS CLOGGED WITH DIRT.  DON’T EVEN INSTALL IT IF YOU ARE GOING TO COVER IT UP WITH DIRT.

DECORATIVE STONE CAN BE USED TO COVER A FRENCH DRAIN AND THEY LOOK GREAT AND LAST A LIFETIME.

French Drains Can Look Great!

 

Installing Cement around Curb Fitting for French Drain

Installing Cement around Curb Fitting for French Drain

 

A French Drain will move large amounts of water from the Drainage Problem Area to the Exit point.

A French Drain will Drain away water that gets to the Drainage Problem Area in 3 ways.

1.  Water gets to the problem area by falling from the sky.

2.  Water gets to the problem area by flowing down hill over the ground.

3.  Water gets to the problem area by flowing underground. (Sub-Surface water flow)

Number 3, Sub-Surface water flow is the big consideration.  When doing a Drainage Diagnostic, this is the area that is many times missed or not considered by less experienced companies.  Oklahoma  Drainage and Sprinkler Repair  relies on 26 years of experience.  Many Times it is cheaper and more effective to install a French Drain over a Surface Drain.  A Surface Drain can’t move as much water as a French Drain, and a Surface Drain can’t Drain away Sub-Surface water.  Surface Drains should be installed in areas where the Drainage Problem area is smaller and is not affected by sub-surface water.

The draw back to a French Drain, is that it is not a pretty as a Surface Drain.

French Drains do a great job running along foundations and driveways.  A French Drain will keep water away from cement and prevent damage to concrete if water should freeze up against it.  A French Drain can keep your foundation Dry.

.

black and white

A good drain outlet should be black and white

Sprinkler Repair Service, French Drain Installation

Posted: January 19, 2020 in french drain, French Drain Repair, sprinkler repair, Sprinkler Repair Service, Sprinkler Service, Sprinkler System Check-Up
Tags: , , , , ,
24

Sprinkler Service Oklahoma City.  Oklahoma Drainage and Sprinkler Repair has provided Expert Sprinkler Repair and Service in Oklahoma City Since 1993.

 

Recently we fixed a broken Sprinkler Pipe under a driveway in Norman.  It was leaking out onto the street every time the sprinkler system ran.   The pipe had to be removed and a new PVC pipe put in its place.

It was located on the west side of Norman in Brookhaven.

Oklahoma Drainage and Sprinkler Repair provide Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

 

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,   Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

We started with the Valves

The Sprinkler Valves were located in the back yard near the pool.  Six valves were located in one place.  They were very tightly connected in one Manifold.  None of the Sprinkler Valves had worked in a long time.  They were Toro Valves that were over 20 years old.  They all had to be replaced.

Surprisingly there was no shut-off valve for the Sprinkler Water.  The water had to be shut off at the Meter so we could install a Manual Shut off valve.  Once installed, the water was turned back on that ran to the house.   The water that ran to the Sprinkler System was shut off with our New Shut Off Valve.

Rainbird Sprinkler Valve

Rainbird Sprinkler Valve

The Sprinkler Valves Were Removed

Now, the 6 valves had to replaced.  The valves that were used were made by Rain Bird.  Before we began, I had to talk to the Customer.  The previous valve design was a bad idea to repeat.

The original Sprinkler Valves were crammed into one large valve box in one very tight manifold.  This is bad because the valves were too close to the fittings.  Simply put, if one valve had to be replaced or worked on in the future, all 6 valves had to be taken out and replaced.   If one valve was bad and 5 worked fine, they all still had to be replaced.

That’s Stupid!

I recommended that an additional Valve Box be installed putting 3 valves in each Valve Box.  This would allow plenty of space between the valve fittings.  If one Sprinkler Valve had to be adjusted or replaced in the future, the other 5 valves need not be disturbed.  Simple Enough!

Check For Leaks

Once the valves were replaced and working, it was time to turn on each Sprinkler Zone, one at a time.  Water was shooting up from the ground in several places in zone 1.  Two broken Sprinkler Pipes and 5 bad Sprinkler Heads in zone 1 had to be fixed and replaced.  We went through each of the 6 zones in similar fashion fixing lots of leaks and replacing bad sprinkler heads.

The Sprinkler Repair Cost About Half of the Cost of Completely New System.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

Sprinkler Head Adjustment is a service provided by Oklahoma Drainage and Sprinkler Repair.  We have adjusted sprinkler heads since 1993.

Many times, Sprinkler heads get, “Out of Wack.”  Lawn mowers and weed eaters are notorious for this.  Sprinkler heads start spraying water in the wrong place.  It is frustrating to water concrete while plants and grass go without moisture.

Pop-Up Sprinkler Heads

Pop-Up Sprinkler Heads can be adjusted several ways.  How far water goes to the left or right can be increased or decreased.  The distance the water goes can also be increased or decreased.  Finally, how high a sprinkler head pops up can be increased or decreased by installing a taller or shorter head.

Sometimes sprinkler heads spray a reduced distance and don’t perform very well due to water scale.  Minerals in the water can completely clog a Pop-Up.  Usually, the sprinkler nozzle on top of the sprinkler head, need only be replaced without replacing the entire head.

Rotor Sprinkler Heads also can be adjusted to the left or right.  Spray Distance can be increased or decreased as well.

Needs Change

What’s going on in your yard can change.  This calls for Sprinkler Head Adjustment.  Adding or removing a swimming pool changes everything concerning sprinkler heads.  Any number of things can change the necessary sprinkler head coverage.

 

 

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes – Sprinkler Head Adjustment – Sprinkler Valve Replacement

We provide Service for Folks in: Norman, Oklahoma City, Edmond, and Moore.

Central and Western Oklahoma is our Service Area since 1993.  

                                                           (405) 203-9419

Check out Sprinkler System Check-Up

Emergency Sprinkler Repair

Sometimes things go wrong with sprinkler systems.

 

IF YOU NEED HELP IN THE MIDDLE OF THE NIGHT OR ON A WEEKEND WITH YOUR SPRINKLER SYSTEM, GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR.  405 203 9419

IT MAY TAKE A FEW HOURS FOR US TO GET THERE BUT WE WILL COME TO HELP.

 

One Common problem is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

 

Sprinkler Repair Facts

 

Oklahoma Drainage and Sprinkler Repair provides Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

 

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,   Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

We started with the Valves

The Sprinkler Valves were located in the back yard near the pool.  Six valves were located in one place.  They were very tightly connected in one Manifold.  None of the Sprinkler Valves had worked in a long time.  They were Toro Valves that were over 20 years old.  They all had to be replaced.

Surprisingly there was no shut-off valve for the Sprinkler Water.  The water had to be shut off at the Meter so we could install a Manual Shut off valve.  Once installed, the water was turned back on that ran to the house.   The water that ran to the Sprinkler System was shut off with our New Shut Off Valve.

The Sprinkler Valves Were Removed

Now, the 6 valves had to replaced.  The valves that were used were made by Rain Bird.  Before we began, I had to talk to the Customer.  The previous valve design was a bad idea to repeat.

The original Sprinkler Valves were crammed into one large valve box in one very tight manifold.  This is bad because the valves were too close to the fittings.  Simply put, if one valve had to be replaced or worked on in the future, all 6 valves had to be taken out and replaced.   If one valve was bad and 5 worked fine, they all still had to be replaced.

That’s Stupid!

I recommended that an additional Valve Box be installed putting 3 valves in each Valve Box.  This would allow plenty of space between the valve fittings.  If one Sprinkler Valve had to be adjusted or replaced in the future, the other 5 valves need not be disturbed.  Simple Enough!

Check For Leaks

Once the valves were replaced and working, it was time to turn on each Sprinkler Zone, one at a time.  Water was shooting up from the ground in several places in zone 1.  Two broken Sprinkler Pipes and 5 bad Sprinkler Heads in zone 1 had to be fixed and replaced.  We went through each of the 6 zones in similar fashion fixing lots of leaks and replacing bad sprinkler heads.

The Sprinkler Repair Cost About Half of the Cost of Completely New System.

 

Oklahoma Drainage –  We install French Drains, Channel Drains, Surface Drains, Sump Pumps and Sod.

If You live in Oklahoma City and water damaging your foundation, We can install a French Drain for you.

If you live in Norman and have water standing on your driveway, We can install a Channel Drain for you.

If you live in Edmond and have water flooding your basement, We can install a Sump Pump for you.

If you live in Moore and have water washing out your flower bed mulch, We can install a Surface Drain for you.

If you live in Yukon and need grass to grow, we can install Sod too!

Servicing all of Central and Western Oklahoma since 1993.

 

If you have water standing in your flowerbed we can install a French Drain For you.  If water is standing on your driveway or sidewalk a Surface Drain or Channel Drain set in concrete might be what you need.  If water is standing in your basement a Sump Pump installation is a good idea.

Drain Pipe for French Drain running under sidewalk

Drainpipe for French Drain running under sidewalk

We Installed a Double Six-inch French Drain in Edmond this week.  A Double Six-Inch French Drain is two six inch French Drains laid side by side in one very wide and deep trench.  It is designed to move a huge amount of water away from a home.   Our customer had several different drainage problems in their back yard.  After a thunderstorm, water would run under their back fence and into their garage.  The back yard was on a steep hillside, and the water would run very fast down the hill and into the garage.

6-Inch French Drain

Oklahoma Drainage and Sprinkler Repair installed 2 large six-inch French Drains across the water’s path.  This allowed the water to be diverted into the French Drain which then ran through drainpipe to a curb outlet at the street.  Three Gutter Down Spouts were connected into the French Drain.  The French Drain created a protective barrier for the garage.  A 12 inch Surface Drain was also included in the Drainage System.  It was placed up against the driveway and connected with 4 inch Solid drain pipe to the 6 inch French Drain.  Water was completely rerouted away from the home.  A French Drain and Surface Drain combination in this case was the best solution to this particular drainage problem.

Installing a Curb Outlet for a French Drain in Edmond
Installing a Curb Outlet for a French Drain in Edmond

 

Oklahoma Drainage installed

a 4-inch French Drain in East Norman this week.  The customer had water standing on the side of his house that was causing foundation damage.  He contracted a Structural Engineer to come out and look at the Drainage Problem and to give him some advice.

Installing Surface Drains In Norman

Installing Surface Drains in Norman

The Structural Engineer recommended a French Drain to protect and draw water away from the foundation.  He said that “he had recommended French Drain Installation to solve similar problems for homeowners many times in the past.  The Structural Engineer was confident that it would solve the Drainage Problem.

 

Next,

our customer went online and found us by searching under, “ Norman Oklahoma French Drain.”
The Gentleman gave us a call to set up an appointment.  We arrived on the agreed time and provided a (Free- No Obligation- Drainage Diagnostic and Quote) We came out and looked at his Drainage Problem and designed a Drainage System to solve his, Standing-Water Problem.”  We also recommended a surface drain in a corner where water was coming off a steep part of the roof and overwhelming the gutter.

 

Installing a Curb Outlet For a French Drain in Edmond

Installing a Curb Outlet for a French Drain in Edmond

The customer let us know that he was ready to move forward.  We scheduled the Drainage System Installation for the following week.

When the scheduled day arrived,

we installed the Drainage System.  The Drain was made up of a 6 inch French Drain running 30 feet along the East side of the house.  It curved around the corner of the house.  At that point a 12-inch Surface Drain was connected to the French Drain with 4 inch pipe.  The 6 inch French Drain at that point changed to 6-inch Solid Drainpipe and continued underground 65 feet to a pop-up emitter at the curb in the front yard near the street.

Surface Drain System in Edmond

Surface Drain System in Edmond

Edmond Oklahoma has been the location for many French Drain Installations for us in the past several years.  Recently we ripped out an old Surface Drain that was under a deck.  The Surface Drain was too small for the job and did not Protect the Foundation from Standing Water. 


 The First step

was to take out part of the deck along the wall.  Next, we took out the Surface Drain and the Three-Inch Pipe which was too small.  Digging a trench along the foundation came next.  We had to ensure the, “Fall” to make sure the water would run from left to right. 

 Next a French Drain Liner needed to be installed.  This was necessary to maintain the integrity of the trench and to keep the French Drainpipe from filling up with sand and getting clogged over the next few years.  Oklahoma Drainage then installed 4-inch ADS Perf/Soc French Drainpipe along the course of the French Drain.  Next, we connected the end of the French Drainpipe to Solid 4 Inch ADS Drainpipe to continue along the trench to the Pop-Up Emitter at the Exit Point.

Running Drain Pipe to the Curb From French Drain in Back Yard

Running Drainpipe to the Curb from French Drain in Back Yard

 

 

 

French Drain Facts, Sprinkler Repair, Oklahoma City, Norman, Altus, Moore

Posted: December 31, 2019 in Drainage System Repair, french drain, French Drain Repair, sprinkler repair, Sprinkler Repair Service, Sprinkler Service
Tags: , , , , ,
102

French Drain Facts, Oklahoma City, Norman, Altus, Moore.

Oklahoma Drainage and Sprinkler Repair can provide the necessary expertise to handle difficult sprinkler repairs.

We install and Service French Drains, Surface Drains, Channel Drains, and Sump Pumps.

In Business since 1993.

Oklahoma Drainage and Sprinkler Repair provides Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

 

Do you have water seeping into your floor vents

after a hard rain?  Is water causing damage to your floors or carpet?

Is water finding a way under your foundation after a thunder storm?

Oklahoma Drainage designs and installs

Drainage Systems that can help stop the damage.

We utilize:  French Drains, Surface Drains, Channel Drains, and Sump Pumps to protect property.  Connecting gutter-downspouts into the Drainage System is always a good idea where possible.

This is a great place for a French Drain

 

The need

for Drainage Systems is increasing in Oklahoma.  During heavy thunder storms,  homes and business need a way to drain water away.  Storm water can cause many kinds of damage.  Here are just a few:

1.  Driveways and Sidewalks can crack and deteriorate

2.  Foundations can crack move or shift

3.  Vents and ducts can fill with water

4.  Mold can be allowed to grow

5.  Trees and Plants and grass can be damaged or drown

Too much water is never a good thing!

Oklahoma can quickly diagnose your Drainage Problem and provide a free quote for a Drainage System.  With twenty years of experience, we realize that Drainage Problems may be very complex and difficult or very straight forward and simple.  Every Drainage Problem is unique to a certain degree.  Don’t kid yourself, Experience Counts!

We take many things into account

when providing a Drainage Diagnostic for a Customer.  We determine:

1.  What is the Primary Water Source to the problem?  Where is the water coming from?

2.  Is there a Secondary Water Source?  Other Places that water may be coming from.    All Drainage Problems have more than one source!

3.  How many Subsequent Water Sources are present?   Some complex Drainage Problems have many water sources.

4.  What exit points are available for gravity to move water away from the problem area?  Where are we trying to take the water to, and how is it

going to be released?  Is more than one exit point possible to increase capacity?

5   How much water must be moved?  What Size Drainpipe is necessary to lessen the chance of being overwhelmed by flooding?    This is a tough

consideration.  (Larger Pipe – Larger Cost to Install)

These are just a few of the considerations for any Drainage System Diagnostic.

DSC00490
4 Inch Drainpipe running under sidewalk
DSC00498
Drainage System Installation in Oklahoma City
DSC00499
Drainage System running to exit point on driveway
Gutter connected to Drainage system

Gutter Connected to Drainage System

The Drainage System

shown in the three above pictures consisted of the following:

Three Gutter Downspouts in the front yard were connected to 4-inch ADS solid Drainpipe with Large Drainage Gutter Connections.  Three lateral 4 inch Pipes were run from each gutter to one outflow pipe moving the water to two exit Pop Up Emitters. One of the Drainpipes ran under the sidewalk to reach the Exit Drainpipe.

This Drainage System had two exit points.  One Pop-Up Emitter was on the edge of the driveway in the front yard.  The other Pop-Up Emitter was installed in the back yard near the property line.  Two exit points allows for a much larger Water Drainage Capacity.  (During Heavy Rains The Drainage System Can Move More Water Faster)

The back yard Exit Pipe then connected to 55 feet of 4-inch French Drain that was installed along the SW corner of the house.  The French Drain provided a protective barrier for that room of the house where water had previously been leaking into the floor vents.  Two Gutter Down Spouts were also connected in the back yard to the Drainage System.

Popup Emitter to release water from a Drainage System in Yukon.
Popup Emitter to release water from a Drainage System in Yukon.

Sprinkler Valve Repair Norman.  Oklahoma Drainage and Sprinkler Repair has provided Expert Sprinkler Repair Service for Norman and all of Central and Western Oklahoma.

Sprinkler Valves are very important to any sprinkler system.  Unfortunately, many things can go wrong with a Sprinkler Valve.

Here is a short list:

Sprinkler Valves can Stick Open.  This means that when it’s time for the Sprinkler Zone to stop, it keeps running and won’t stop or shut off.

Sprinkler Valves can leak. This can be from the “PVC Pipe” Connections, or the “Bleed” Screw is loose.

Sprinkler Valve Wiring can short out or come loose.  All of a sudden, the Sprinkler Zone won’t work.

The above list are just the most common problems for Sprinkler Valves.

 

Sprinkler Valve Replacement is a service that Oklahoma Drainage has provided Since 1993.  Recently we removed 3 Rainbird Sprinkler Valves and replaced them with new ones.  The valves had been crushed accidentally when a landscaper drove his truck across the yard.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provides Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

First Step

First, we dug up a good working area surrounding the broken Sprinkler Valves.  Next, we cut out the broken valves and crushed PVC pipes.  Finally, PVC pipe was cut and glued with new Sprinkler Valves following the original design and configuration.  In this case the three original sprinkler valves were connected to each other inside one Valve Box.

We aren’t done yet though; two sprinkler wires must be connected to each Valve.  One sprinkler wire is the “Common Ground.”  The other wire is the power wire.  All the sprinkler wiring is connected with water-proof wire connections.

The Common Ground wire and the Individual Power Wires all come from the Sprinkler Controller.  Each Sprinkler Valve has its own power wire coming from the Controller.  All the Sprinkler Valves are Connected to the Same Common Ground Wire.

Before We Finish

Before dirt can be put back around the new valves, testing must be done.  Each valve must be turned on, “one-at-a-time,” at the Controller to ensure good wire connection and functionality.  Also, the Sprinkler Valves must be checked for leaks in the PVC Pipe.

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes – Sprinkler Head Adjustment – Sprinkler Valve Replacement

Servicing all of Central and Western Oklahoma since 1993.  405 203 9419

Sometimes things go wrong with sprinkler systems.

 

IF YOU NEED HELP GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR.  405 203 9419

Sprinkler Repair Service Edmond, French Drain Installation, Edmond, Lawton, Moore, Oklahoma City, Altus —

Posted: December 11, 2019 in french drain, French Drain Repair, sprinkler repair, sprinkler repair contractor, Sprinkler Repair Service, Sprinkler Service
Tags: , , , , , ,
106

Norman Sprinkler Repair, Edmond, Oklahoma City

Recently we fixed a broken Sprinkler Pipe under a driveway in Norman.  It was leaking out onto the street every time the sprinkler system ran.   The pipe had to be removed and a new PVC pipe put in its place.

It was located on the west side of Norman in Brookhaven.

Oklahoma Drainage and Sprinkler Repair provide Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

 

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,   Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

We started with the Valves

The Sprinkler Valves were located in the back yard near the pool.  Six valves were located in one place.  They were very tightly connected in one Manifold.  None of the Sprinkler Valves had worked in a long time.  They were Toro Valves that were over 20 years old.  They all had to be replaced.

Surprisingly there was no shut-off valve for the Sprinkler Water.  The water had to be shut off at the Meter so we could install a Manual Shut off valve.  Once installed, the water was turned back on that ran to the house.   The water that ran to the Sprinkler System was shut off with our New Shut Off Valve.

Rainbird Sprinkler Valve

Rainbird Sprinkler Valve

The Sprinkler Valves Were Removed

Now, the 6 valves had to replaced.  The valves that were used were made by Rain Bird.  Before we began, I had to talk to the Customer.  The previous valve design was a bad idea to repeat.

The original Sprinkler Valves were crammed into one large valve box in one very tight manifold.  This is bad because the valves were too close to the fittings.  Simply put, if one valve had to be replaced or worked on in the future, all 6 valves had to be taken out and replaced.   If one valve was bad and 5 worked fine, they all still had to be replaced.

That’s Stupid!

I recommended that an additional Valve Box be installed putting 3 valves in each Valve Box.  This would allow plenty of space between the valve fittings.  If one Sprinkler Valve had to be adjusted or replaced in the future, the other 5 valves need not be disturbed.  Simple Enough!

Check For Leaks

Once the valves were replaced and working, it was time to turn on each Sprinkler Zone, one at a time.  Water was shooting up from the ground in several places in zone 1.  Two broken Sprinkler Pipes and 5 bad Sprinkler Heads in zone 1 had to be fixed and replaced.  We went through each of the 6 zones in similar fashion fixing lots of leaks and replacing bad sprinkler heads.

The Sprinkler Repair Cost About Half of the Cost of Completely New System.

Oklahoma Drainage 405 203 9419 — We provide:

    French Drain Installation, Surface Drain Installation, Drainage System Installation

 

French Drain Running Through Low Areas

French Drain with stepping stones

WHAT SIZE DRAINPIPE FOR FRENCH DRAINS?

French Drains can be decorated with many types of stone

French Drains can be decorated with many types of stone

French Drains can utilize

several types and sizes of French Drainpipe.  An older type that is not commonly used any more is 4 inch PVC Pipe with large half inch holes drilled in the Pipe.  This doesn’t work very well,   Because the holes are too large and the number of holes in the French Drainpipe are too few.  Also, there is no filter or “Soc” around this particular French Drainpipe.  If it is used in sandy or loose soil the holes will clog and the pipe will fill up with sand.  PVC French Drainpipe should be avoided.

ADS French Drainpipe

is much better, the holes are smaller and much more numerous.  It also comes inside a soc that acts as a filter and helps keep sand and debris out of the French Drainpipe.  It works very well.

French Drain in flowerbed

French Drain in flowerbed

4 Inch Perforated ADS Pipe

For Small business and Residential French Drains, Four inch ADS Perf/Soc French Drainpipe is adequate and the most common.  It is used for the majority of all French Drains installed.  French Drains can be installed using 3 inch ADS Perf/Soc but many times it is too small and can be overwhelmed by a heavy rain or from a bad design.  (Too many gutter down spouts connected directly into the French Drain, For Example) Three Inch French Drainpipe should be avoided if possible.

Six inch  ADS Perf/Soc French Drainpipe is usually a good idea when possible.  It carries a much larger volume of water.  Six Inch French Drains are rarely overwhelmed.

Installing Gravel on top of a 6 inch French Drain

Installing Gravel on top of a 6-inch French Drain

The Drawbacks to 6-inch French Drain installation are:  1.  The Materials Cost is higher for six-inch French Drain Compared to Four Inch Pipe.
                                                                                                                    2.  Many times 6 Inch French Drainpipe is too large for many applications, Such as going under a fence or sidewalk.  
                                                                                                                   3.  The trench for a 6-inch French Drain must be much larger than a 4 Inch
                                                                                                                   4.  The amount of gravel or limestone or River Rock used to Cover the 6-inch French Drain is Much larger
 
All things being considered, the performance and longevity of a 6-inch French Drain is well worth it if you are trying to protect something of value to you!  If the higher cost and the additional labor and materials are not a problem and 6 inch French Drainpipe is not too big for what you want to do then a 6 inch French Drain would be the best.  
 
 
 
 

Sprinkler Repair Contractor, Oklahoma City, Norman, Moore, Edmond

Posted: November 15, 2019 in Drainage System, Drainage System Repair, french drain, French Drain Contractor, sprinkler repair contractor
Tags: , , ,
106

Sprinkler Repair Contractor

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provides Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

Sprinkler Valve Replacement

Oklahoma City Sprinkler Repair

FRENCH DRAIN, SURFACE DRAIN PHOTOS AND INFORMATION

 Standing water can cause many types of property damage ranging from foundation problems to cracked sidewalks and dead plants and shrubs.  If you have need of French Drain or Surface Drain, give us a  call.  We provide free estimates for all of central Oklahoma.

 

French Drain With Colored Gravel in Oklahoma City

French Drain With Colored Gravel in Oklahoma City

Installing Cement around Curb Fitting for French Drain in Norman

Installing Cement around Curb Fitting for French Drain in Norman

Some Drainage Systems are complex and incorporate several types of drains.  Most Drainage Systems , however are basic and require just one type of Drain.  Oklahoma Drainage and Sprinkler Repair installs a variety of drains to solve a variety of problems. French Drains, Surface Drains, and Channel Drains are most commonly used.  If you live in Edmond and need a Channel Drain installed across your driveway, or if you live in Norman and need a French Drain in your backyard, or if you live in Oklahoma City and need a Surface drain installed next to your sidewalk, we can help.

Channel Drain Installed by CMG In Yukon

Channel Drain Installed In Yukon

Channel Drains are one kind of Surface Drain that we install in concrete.

The most common Drain that we install is the French Drain.  This is because the French Drain is versatile.  It can handle Surface Water Problems or Underground Water Problems (sub-surface).  A huge mistake that many people make is assuming that water gets to a Problem Drainage Area by flowing over the surface only.  For example, if water is flowing down hill underground toward your home’s foundation, the only way to stop or intercept it is with a French Drain.  Water can flow laterally into a perforated French Drain Pipe.  It is then diverted away from the Problem Drainage Area to an Exit Point.

Popup Emitter to release water from a French Drain in Yukon

Popup Emitter to release water from a French Drain in Yukon

Pop Up Emitters can release water from Surface Drains or French Drains.  They can release water on to sidewalks or driveways, or out in the middle of yards.

A  French Drain is completely different from a Surface Drain.  A basic French Drain consists of a Perforated Drain Pipe in the bottom of a trench.  A  Trench Liner is sometimes used depending on the Drainage System Design and the type of soil.   The Drain Pipe should have a neoprene sock around the Perforated Drain Pipe.   This is to ensure that the Drain Pipe does not become clogged. A trench is dug that is slightly wider than the French Drain Pipe that is being used.  There are several sizes of French Drain Pipe.   Three Inch, Four Inch, and Six Inch are the most common sizes of French drain Pipe. The dirt that is taken out to make the trench is hauled away.  It is replaced by some type of small stone or gravel depending on what is desired or available.  I prefer crushed 1 inch lime stone.  It is the most economical option in my area.  Pea Gravel or some other type of small stone can work just as well.    The lime-stone or gravel is placed in the trench on top of the perforated Drain Pipe and filled all the way to the surface (ground level).   In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drain Pipe or the Gravel are installed.  This helps maintain the integrity of the trench over time.  It also increases the cost of the French Drain and the amount of time to install it.  I install a trench liner in a French Drain about 20% of the time.  Most of the time a liner in not needed.

 

clogged French Drain Pipe

result of French Drain Installed Incorrectly

 

Pipe running to street form French Drain in back yard.

Pipe running to street form French Drain in back yard.

When we run Drain Pipe across yards to an Exit Point, the sod usually can be put back into place and in a few days you can’t tell a French Drain was ever Installed.
A French Drain is designed to handle a large volume of water and cover a large area. The Drain is anyplace the trench goes. It has many applications and can be used in many situations.  It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Down-Spouts connected to it.
The main downfall of a French Drain is that they, for the most part aren’t very pretty.  They don’t look very nice in a yard once they are completed.
Depending on the area the French Drain is installed and the type of grass around the French Drain, will dictate whether grass grows over the lime stone.  Grass can grow up and through the gravel in the French Drain over time eventually covering the gravel.  This is OK.  It won’t have a measurable effect on the performance of the French Drain.  In some cases thick grass growing up through the French Drain will create a natural “Thatch” filter.  This makes the French Drain invisible.  The trick is to allow the grass to grow over the French Drain Gravel without covering it up with dirt.  Grasses such as Bermuda which grow well in the sun will put out runners and new roots and will grow up and through the French Drain.  This will not affect the performance of the French Drain.  The problem is that some times depending on the type of soil involved, it may take a long time to completely cover up the French Drain.  Sprinkling grass seed down in the gravel will speed up the process.

DON’T COVER THE GRAVEL IN THE FRENCH DRAIN WITH DIRT.  THE FRENCH DRAIN WON’T WORK IF THE TRENCH IS CLOGGED WITH DIRT.  DON’T EVEN INSTALL IT IF YOU ARE GOING TO COVER IT UP WITH DIRT.   

If you install a French Drain in a sunny area, you can:
                                         A.  Leave the  French Drain as-is and allow grass to grow over it in time.
                                         B.  Add grass seed directly to the French Drain gravel with (Light Hand Watering) to speed the growth process
                                         C.  Leave the French Drain as-is but decorate it with stepping stones and landscaping rocks ( leaving large cracks between stones to allow water to get into the French Drain,
2
If you install a French Drain in a shady area you can:
                                        A.  Leave the French Drain as-is, it will work well and look as it did for many years.

                                        B.  Leave the French Drain as-is, but decorate it with stepping stones or landscaping rocks.  Many French Drains are hidden under rock walk ways.

Sometimes Surface Drains make more sense when the Drainage Problem area is fairly small with Surface Water Flowing into it.

 

French Drain with stepping stones

French Drain with stepping stones

Sprinkler Repair, French Drain Repair,

Posted: October 26, 2015 in french drain, French Drain Contractor, French Drain Repair, sprinkler repair, Sprinkler Repair Service, Sprinkler Service
Tags: , , , ,
0

Oklahoma Drainage and Sprinkler Repair has fixed Sprinkler Leaks in Edmond since 1993.

Sprinkler Repair is also very popular this time of year.  Folks in Central Oklahoma are turning on their Sprinkler Systems and discovering problems.

No PVC Primer Used.  Yikes!!!

We fixed several leaks in a Sprinkler System in Edmond.  The sprinkler pipes were leaking in several places.  Each leak had to be cut out and replaced.

The Sprinkler System was fairly new.  It was installed last summer by a Pool Company that also installs cheap sprinkler systems.

All the joints in the sprinkler pipes were glued together with clear PVC Cement.  That part is OK, but they cut some corners and didn’t use PVC Primer with the glue.  As a result, the joints didn’t bond very well and many of them blew apart this spring when the sprinkler systems were turned on.  (Thus, all the leaks)

I suspect we will have to go back several times to fix additional leaks.  We can only warranty the PVC joints that we have replaced.   Cheaper isn’t always better.

 

Sprinkler pipes may leak for many reasons.  Pipes that are too shallow can freeze and break during the cold of winter.  Repair of PVC Sprinkler pipe in cold temperatures can be difficult.  Frozen Ground is difficult to dig up to get to the damaged pipe.  PVC Glue and Primer don’t bond very well in temperatures that are low.  Even using “Hot Glue,” which is designed to be used in cold temperatures doesn’t always produce the best results.

Oklahoma Drainage and Sprinkler Repair can provide the necessary expertise to handle difficult sprinkler repairs.

Oklahoma Drainage and Sprinkler Repair provide Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

One Common Problem

One Common problem is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

 

Inside the valve box is a plastic handle that can turn off the water to the sprinkler system.  It can be blue or red or grey in color.

Many times, the valve box will be full of dirt, and you can’t turn or even see the handle until some of the dirt has been dug out by hand.

 

Water might be shooting up in the air somewhere on your property.  This can be caused by a broken sprinkler pipe or sprinkler valve.

SHUT OFF THE SPRINKLER WATER IF YOU CAN AND GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR. SERVICING ALL OF CENTRAL AND WESTERN OKLAHOMA.

405 203 9419

Servicing Oklahoma City, Norman, Edmond and all of Central and Western Oklahoma

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,     Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

 

 

A French Drain is completely different from a Surface Drain. A basic French Drain consists of a Perforated Drainpipe in the bottom of a trench.

A Trench Liner is sometimes used depending on the Drainage System Design and the type of soil.

The Drainpipe should have a neoprene sock around the Perforated Drainpipe. This is to ensure that the Drainpipe does not become clogged.

A trench is dug that is slightly wider than the French Drainpipe that is being used.

There are several sizes of French Drainpipe. Three Inch, Four Inch, and Six Inch are the most common sizes of French drainpipe. The dirt that is taken out to make the trench is hauled away. It is replaced by some type of small stone or gravel depending on what is desired or available.

I prefer crushed 1 inch limestone. It is the most economical option in my area. Pea Gravel or some other type of small stone can work just as well. The limestone or gravel is placed in the trench on top of the perforated Drainpipe and filled all the way to the surface (ground level).

In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drainpipe or the Gravel are installed. This helps maintain the integrity of the trench over time. It also increases the cost of the French Drain and the amount of time to install it. I install a trench liner in a French Drain every time.

Lawn Sprinkler Leak Repair, French Drain, Oklahoma City, Drain Repair, Drainage Systems

Posted: October 4, 2014 in french drain, French Drain Contractor, Leak Repair, Leaking Sprinkler Pioes, Leaking Sprinkler Pipes, Oklahoma City French Drain, sprinkler repair
Tags: , ,
7

Lawn Sprinkler Leak Repair

Lawn Sprinkler Repair

Lawn Sprinkler Leak Repair

Lawn Sprinklers can have pipes that leak.   PVC Pipe is the most common Sprinkler System Pipe and leaks definitely are possible.

Leaking Sprinkler Pipes

Leaks can occur near Sprinkler Valves.  Water travels through Sprinkler Valves and can leak going in or coming out.

Many Cities require a back-flow valve to protect the City’s water supply.  It can also leak as water passes through the valve.

Leaks can also occur due to tree roots stressing Sprinkler Pipes.  The pipes can be twisted by roots and crack or break.

Water inside Sprinkler Pipes can freeze and break or crack the PVC Pipe.

Move sprinkler heads, Norman, Oklahoma City, Edmond

There are many reasons for moving Sprinkler Heads.

If you put in a new pool, most of the sprinkler heads will need to be moved.

Sprinkler Heads need to be moved if you have new landscaping installed.

Sometimes Sprinkler Heads weren’t in a good place to begin with.  They need to be moved!

Oklahoma Drainage and Sprinkler Repair can help.  We have been moving Sprinkler Heads since 1993.

In 32 years, we have moved a lot of Heads for Customers in Central and Western Oklahoma.

 

Oklahoma Drainage and Sprinkler Repair provide Expert Service for Sprinkler Heads, Valves, Controllers and all other Sprinkler System difficulties.  We service Norman, Edmond, Oklahoma City, Moore, Yukon, Mustang, and Midwest City.

Emergency Sprinkler Repair is also available.

405 203 9419

Sprinkler Head Installation

Moving Sprinkler Head

Sprinkler Controller Repair is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,   Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

We started with the Valves

The Sprinkler Valves were located in the back yard near the pool.  Six valves were located in one place.  They were very tightly connected in one Manifold.  None of the Sprinkler Valves had worked in a long time.  They were Toro Valves that were over 20 years old.  They all had to be replaced.

Surprisingly there was no shut-off valve for the Sprinkler Water.  The water had to be shut off at the Meter so we could install a Manual Shut off valve.  Once installed, the water was turned back on that ran to the house.   The water that ran to the Sprinkler System was shut off with our New Shut Off Valve.

Rainbird Sprinkler Valve

Rainbird Sprinkler Valve

The Sprinkler Valves Were Removed

Now, the 6 valves had to replaced.  The valves that were used were made by Rain Bird.  Before we began, I had to talk to the Customer.  The previous valve design was a bad idea to repeat.

The original Sprinkler Valves were crammed into one large valve box in one very tight manifold.  This is bad because the valves were too close to the fittings.  Simply put, if one valve had to be replaced or worked on in the future, all 6 valves had to be taken out and replaced.   If one valve was bad and 5 worked fine, they all still had to be replaced.

That’s Stupid!

I recommended that an additional Valve Box be installed putting 3 valves in each Valve Box.  This would allow plenty of space between the valve fittings.  If one Sprinkler Valve had to be adjusted or replaced in the future, the other 5 valves need not be disturbed.  Simple Enough!

Check For Leaks

Once the valves were replaced and working, it was time to turn on each Sprinkler Zone, one at a time.  Water was shooting up from the ground in several places in zone 1.  Two broken Sprinkler Pipes and 5 bad Sprinkler Heads in zone 1 had to be fixed and replaced.  We went through each of the 6 zones in similar fashion fixing lots of leaks and replacing bad sprinkler heads.

The Sprinkler Repair Cost About Half of the Cost of Completely New System.

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

Sprinkler Head Adjustment is a service provided by Oklahoma Drainage and Sprinkler Repair.  We have adjusted sprinkler heads since 1993.

Many times, Sprinkler heads get, “Out of Wack.”  Lawn mowers and weed eaters are notorious for this.  Sprinkler heads start spraying water in the wrong place.  It is frustrating to water concrete while plants and grass go without moisture.

Pop-Up Sprinkler Heads

Pop-Up Sprinkler Heads can be adjusted several ways.  How far water goes to the left or right can be increased or decreased.  The distance the water goes can also be increased or decreased.  Finally, how high a sprinkler head pops up can be increased or decreased by installing a taller or shorter head.

Sometimes sprinkler heads spray a reduced distance and don’t perform very well due to water scale.  Minerals in the water can completely clog a Pop-Up.  Usually, the sprinkler nozzle on top of the sprinkler head, need only be replaced without replacing the entire head.

Rotor Sprinkler Heads also can be adjusted to the left or right.  Spray Distance can be increased or decreased as well.

Needs Change

What’s going on in your yard can change.  This calls for Sprinkler Head Adjustment.  Adding or removing a swimming pool changes everything concerning sprinkler heads.  Any number of things can change the necessary sprinkler head coverage.

 

 

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes – Sprinkler Head Adjustment – Sprinkler Valve Replacement

We provide Service for Folks in: Norman, Oklahoma City, Edmond, and Moore.

Central and Western Oklahoma is our Service Area since 1993.  

                                                           (405) 203-9419

Check out Sprinkler System Check-Up

Emergency Sprinkler Repair

Sometimes things go wrong with sprinkler systems.

 

IF YOU NEED HELP IN THE MIDDLE OF THE NIGHT OR ON A WEEKEND WITH YOUR SPRINKLER SYSTEM, GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR.  405 203 9419

IT MAY TAKE A FEW HOURS FOR US TO GET THERE BUT WE WILL COME TO HELP.

 

One Common problem is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

 

Inside the valve box is a plastic handle that can turn off the water to the sprinkler system.  It can be blue or red or grey in color.

Many times, the valve box will be full of dirt, and you can’t turn or even see the handle until some of the dirt has been dug out by hand.

 

Water might be shooting up in the air somewhere on your property.  This can be caused by a broken sprinkler pipe or sprinkler valve.

SHUT OFF THE SPRINKLER WATER IF YOU CAN AND GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR. SERVICING ALL OF CENTRAL AND WESTERN OKLAHOMA.

405 203 9419

Servicing Oklahoma City, Norman, Edmond and all of Central and Western Oklahoma

 

 

FRENCH DRAINS SOLVE LOTS OF DRAINAGE PROBLEMS!

 

We just finished a 4 inch Drainage System in Yukon.  It was a complicated system to install.  It utilized 4 inch French Drain in the flower beds,  12 inch Surface Drains on the side of the house,  6 inch French Drain along the garage foundation with 2 Pop – Up Emitters in the back yard and 3 Curb Fittings in the front.    First we installed 4-inch French Drain in the flowerbeds on both sides of the front door.  We connected 4 inch solid Drainpipe into the French Drain and ran them underside walk to the curb.  Next we cut the curb with a concrete saw and installed 3 curb outlets for 3 separate French Drains.

Installing a Curb Outlet for a French Drain in Oklahoma City

Installing a Curb Outlet for a French Drain in Oklahoma City

Next we installed 4 12 Inch Drain Basins with grates along both sides of the house continuing with Solid Drainpipe to the Pop-Up Emitters on the back fence. Finally we completed the Drainage System by installing a long run of 6 inch French Drain down the side of the garage foundation.

Installing the French Drains in the flower beds

was the most difficult and took the most time.  Each French Drain took over a ton of crushed limestone to fill the French Drain trench.  The Six inch French Drain took even more limestone.

French Drain in Oklahoma City

French Drain in Oklahoma City

French Drains can utilize  several types and sizes of French Drain Pipe.  An older type that is not commonly used any more is 4 inch PVC Pipe with large half inch holes drilled in the Pipe.  This doesn’t work very well,   Because the holes are too large and the number of holes in the French Drain Pipe are too few.  Also there is no filter or “Soc” around this particular French Drain Pipe.  If it is used in sandy or loose soil the holes will clog and the pipe will fill up with sand.  PVC French Drain Pipe should be avoided.

Installing a Drain Pipe For a French Drain that Releases water through a Pop-Up Emitter at the Street

Installing a Drainpipe For a French Drain that Releases water through a Pop-Up Emitter at the Street

ADS French Drainpipe

is much better, the holes are smaller and much more numerous.  It also comes inside a soc that acts as a filter and helps keep sand and debris out of the French Drainpipe.  It works very well.

For Small business and Residential French Drains, Four inch ADS Perf/Soc French Drain pipe is adequate and the most common.  It is used for the majority of all French Drains installed.  French Drains can be installed using 3 inch ADS Perf/Soc but many times it is too small and can be overwhelmed by a heavy rain or from a bad design.  (Too many gutter down spouts connected directly into the French Drain, For Example)  Three Inch French Drain Pipe should be avoided if possible.

Connecting Gutter into French Drain System in Moore

Connecting Gutter into French Drain System in Moore

Six inch  ADS Perf/Soc French Drainpipe is usually a good idea when possible.  It carries a much larger volume of water.  Six Inch French Drains are rarely overwhelmed.

The Drawbacks to 6 inch French Drain installation are:

 
 1.  The Materials Cost is higher for six-inch French Drain Compared to Four Inch Pipe.
                                                                                                                    2.  Many times 6 Inch French Drainpipe is too large for many applications, Such as going under a fence or sidewalk.  
                                                                                                                   3.  The trench for a 6 inch French Drain must be much larger than a 4 Inch
                                                                                                                   4.  The amount of gravel or limestone or River Rock used to Cover the 6 inch French Drain is Much larger
 
All things being considered, the performance and longevity of a 6 inch French Drain is well worth it if you are trying to protect something of value to you!  If the higher cost and the additional labor and materials are not a problem and 6 inch French Drain pipe is not too big for what you want to do then a 6 inch French Drain would be the best.  
 
 

Sprinkler Repair Information, French Drain, Oklahoma City, Norman, Edmond

Posted: June 23, 2013 in french drain, French Drain Repair, French Drain Service, sprinkler repair, Sprinkler Repair Service
Tags: , , ,
1

Sprinkler Repair Information

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR –

Servicing Central and Western Oklahoma since 1993.

Sprinkler Repair – French Drain Installation – Drainage System Installation

This week Oklahoma Drainage and Sprinkler Repair overhauled a flowerbed Sprinkler Zone in a Sprinkler System in East Norman.

The homeowner had an existing Sprinkler System that was in good shape for the most part but had problems with the flowerbed Sprinkler Zone.

It had a Drip Sprinkler Zone installed.  The Drip Sprinkler System was installed correctly but was not practical for the flower bed.

The flowerbed was very sandy and could not retain water very well even with good mulch.  Plus, the surrounding brick walls increased the amount of heat the plants had to endure in the summer.  The Drip Sprinkler Zone could not provide enough water fast enough for the plants.

We provide:

1.  Sprinkler Valve Problems

2.  Sprinkler Wiring Problems

3.  Sprinkler Controller Problems / Sprinkler Clock Problems

4.  Sprinkler Head Problems

5.  Sprinkler Pipe Problems

6.  Sprinkler Coverage Problems

7.  Sprinkler Redesign Problems for new fences or swimming pools.

If you have water running down the street in the middle of the night because your sprinkler system is leaking or won’t shut off, give Oklahoma Drainage and Sprinkler Repair a call.  405 203 9419

Sprinkler Repair

is a central focus for Oklahoma Drainage and Sprinkler Repair.  Just like any car or home, a lawn sprinkler system must be updated and maintained.  Typically, people wait till spring to get the kinks worked out of their sprinkler system.

Sprinkler Repair is an ongoing issue for any sprinkler system.  Folks in Central Oklahoma are turning on their Sprinkler Systems and discovering problems.

We fixed several leaks in a Sprinkler System in Edmond.

The sprinkler pipes were leaking in several places.  Each leak had to be cut out and replaced.

The Sprinkler System was fairly new.  It was installed last summer by a Pool Company that also installs cheap sprinkler systems.

All the joints in the sprinkler pipes

were glued together with clear PVC Cement.  That part is OK, but they cut some corners and didn’t use PVC Primer with the glue.  As a result, the joints didn’t bond very well and many of them blew apart this spring when the sprinkler systems were turned on.  (Thus, all the leaks) I suspect we will have to go back several times to fix additional leaks.

We can only warranty the PVC joints that we have replaced.   Cheaper isn’t always better.

Today we did a sprinkler repair in Norman.  The sprinkler system needed a checkup.  We went through each sprinkler zone and identified several different problems.  Zone 2 had a cracked sprinkler pipe in a flower bed.

Next, Zone 4 had a broken sprinkler rotor on the edge of the driveway that had been driven over and broken.  Zone 6 and 7 each had a couple of pop-up spray heads that were worn out and would not pop-up.  The diagnosis and the repair took less than two hours.  Now their sprinkler system is running great!

Don’t Wait!

I can tell you this, DON’T WAIT TILL MARCH TO GET YOUR SPRINKLER SYSTEM IN SHAPE.  BY APRIL THERE WILL BE A FLOOD OF PEOPLE TRYING TO GET BROKEN SPRINKLER HEADS FIXED OR NEW SPRINKLER CONTROLLERS INSTALLED OR LEAKING BACK-FLOW VALVES REPLACED.

CONSIDER GETTING YOUR SPRINKLER REPAIR WORK DONE ANY TIME OTHER THAN THE SPRING.  FOR THOSE OF YOU WHO HAVE NO CHOICE AND MUST HAVE WORK DONE IN THE SPRING, SCHEDULE AS EARLY AS YOU CAN.

OUR SPRINKLER REPAIR WORK IS TOP QUALITY AND OUR PRICES ARE FAIR.  IT IS OUR GOAL TO GET TO CUSTOMERS QUICKLY IN MARCH AND APRIL, WHILE MAINTAINING OUR QUALITY OF WORK.

 

Oklahoma Drainage and Sprinkler Repair

can help if you need to re-design your Sprinkler System.  If for example you are adding a swimming pool in your back yard, we can move the Sprinkler Heads and Sprinkler Pipes to fit the new dimensions of your yard.  We can redesign or add-on to sprinkler systems where the homeowners need change.

Maybe you don’t need a large part of your sprinkler system redesigned.  You May just want a few heads moved to new locations.

Whatever your Sprinkler needs may be, Oklahoma Drainage and Sprinkler Repair can help.  Give us a call at : 405 203 9419

 

Sprinkler Repair Service Provided by Oklahoma Drainage and Sprinkler Repair

Since 1993 we have Replaced Sprinkler Valves that were sticking or were wore out.

Thousands of Sprinkler Heads have been adjusted.

Countless Sprinkler Controllers have been Reprogramed or Replaced.

We also have fixed a broken Sprinkler Pipe or Two.  Seems like a million.  Ok, not that many.

I wonder how many?  A lot!!!!

Oklahoma Drainage and Sprinkler Repair provides Service for all of Central Oklahoma Including:  Oklahoma City, Norman, Edmond, Moore, Yukon and Mustang.

Sprinkler Repair for us is very clear.  We have been doing it a long time and have become very good at it.  Many times, we get called in to handle tough problems that the initial Sprinkler Company couldn’t handle.

 

Drainage System Contractor Oklahoma City, Norman, Edmond

 

Drainage Systems are designed to protect your home or business from standing water.  Storm-Water Runoff can cause damage in many ways.  Water from your gutters can seep down into your home’s foundation if it has no good way to drain off.  If the temperature then drops below freezing, the water around your foundation can freeze and cause serious damage to the home’s foundation.  Foundation repair can cost more than a Drainage System.

French Drain Installation

French drain Installation
with trench liner and pipe filter

Oklahoma Drainage

typically make use of, French Drains, Surface Drains, or Channel Drains.  Depending on the Drainage Problem, A Drainage System may utilize one or several types of Drains.  Oklahoma Drainage might install, for example, A Surface Drain in the middle of a driveway that runs to a gutter that is connected into the drainpipe.

The Drainpipe might continue to a French Drain running parallel to a home’s foundation.  Next the drainpipe might continue to a channel drain cutting across a sidewalk.  The Drainpipe might then reach its exit point running out through a curb fitting installed and cemented through the curb.

A Surface Drain

basically, is a basin that has a grate on the top.  A drainpipe is connected to the basin below ground.  The water flows in through the grate and down into the basin.

The water then exits the Basin through the Drainpipe and move toward the exit point of the Drainage System.  Surface Drains are designed to handle water that accumulates in a low area.   These areas should not be too large or broad, and the water that drains into a surface drain should not be moving very fast.

Surface Drains can become overwhelmed if they are placed in an area that must move a large volume of water, quickly.  Selecting the correct drain for the specific drainage problem is a benefit that Oklahoma Drainage provides through twenty years of experience.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR, Provides Expert Sprinkler Repair for:  Sprinkler Valves, Sprinkler Heads, Sprinkler Controllers, and the most common problem, Sprinkler Pipes or Sprinkler Leaks.

Sprinkler Repair Service is provided for: Oklahoma City, Norman, Edmond, Yukon, Mustang, Moore, Midwest City, Blanchard, New Castle, and all surrounding areas.

Sprinkler Irrigation Service, French Drain Installation,

Posted: August 15, 2011 in french drain, sprinkler repair, Sprinkler Repair Service, Sprinkler Service
Tags: , , ,
26

 

Sprinkler Irrigation Service.  Oklahoma Drainage and Sprinkler Repair Provides Sprinkler Irrigation Service for all of Central Oklahoma.

is a service provided by Oklahoma Drainage.  A Sprinkler Controller is the “Brain,” of a Sprinkler System.  They can wear out or stop working.  Power surges in the home can cause damage to a controller.

Programming can be difficult for homeowners.  We can help with programming or replace a Sprinkler Module if it is defective.

Start Time Programming

“Start Time” programing many times is confusing for homeowners.  The definition of a Start Time is a time that is chosen for the sprinkler system to start watering.  It causes zone 1 to start running.  When zone 1 is finished it automatically stops and zone 2 begins.  When Zone 2 is complete it stops and zone 3 begins.  Simple enough Right!  This continues until the last zone programed available runs.

The confusion begins when people think that a time needs to be set to start zone 2 and 3 and so on.  This is not the case.  They follow zone 1 which has the only Start Time programmed into the controller.

Be Careful with Multiple Start Times, just use One at first.

Sprinkler Controllers have a feature providing multiple start times, up to 4 Start Times are usually available.  These additional start times are only used when a person wants to run the entire system more than once in a 24-hour period.

For Example, the first Start Time is set at 9Am.  Zone 1 begins to run at 9am.  When Zone 1 is done, say 10 minutes later, Zone 2 begins and runs for 10 minutes, then zone 3 follows and so on.  By 10 am let’s say all the zones have run.  Let’s say 8 hours later you have a second start time at 6 Pm.  Zone 1 comes on and runs and by 7pm all the zones have run again.  So, the controller has 2 start times which have caused the Sprinkler System to run start to finish twice in a 24-hour period.

Here is the big problem!  Some Homeowners believe the second start time is to start zone 2 running.  They also think that the 3rd start time is to start zone 3 and the 4-start time is to run zone 4.  No!!

So, this is how they program the controller.  At 9am they have a start time and zone 1 starts.  The homeowner programs a second start time at 9:10 am to mistakenly start zone 2.  Nope!  It starts zone 1 all over again.  At 9:2o they have a 3rd start time for zone 3.  Nope!  It starts zone 1 for a third time.  Now the controller is stuck in a loop and zone 1 runs constantly and won’t shut off.

If Sprinkler Controller Programming is confusing?  Make sure you only have One Start Time!

“Run Time,” is completed Next.  It determines how long each zone runs.  Zone One 10 Minutes,     Zone Two, 15 Minutes, Zone Three 8 Minutes.  You can set how long you want each zone to run.

French Drain Repair and Installation is a Central Focus for Oklahoma Drainage.  We installed our first French Drain and completed our first Sprinkler Repair in Norman in 1993.

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps.

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes – Sprinkler Head Adjustment – Sprinkler Valve Replacement

We provide Service for Folks in: Norman, Oklahoma City, Edmond, and Moore.

Central and Western Oklahoma is our Service Area since 1993.  

                                                           (405) 203-9419

Emergency Sprinkler Repair

Sometimes things go wrong with sprinkler systems.

 

IF YOU NEED HELP IN THE MIDDLE OF THE NIGHT OR ON A WEEKEND WITH YOUR SPRINKLER SYSTEM, GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR.  405 203 9419

IT MAY TAKE A FEW HOURS FOR US TO GET THERE BUT WE WILL COME TO HELP.

 

One Common problem is that they continue to run and won’t shut off.  In most cases this is a problem with a sprinkler valve that has “Stuck” in the on position.

This can be temporarily solved by shutting of the Emergency Shutoff Valve.  The problem is that some sprinkler systems don’t have one to turn off or if they do the homeowner doesn’t know where it is.

It may be on the back-flow valve which may be located on the side of the house under a big plastic fake rock.

Many sprinkler systems in Oklahoma have them. (50 % ?)  Under the plastic rock is a back-flow valve with two shut off handles.  Usually, they have blue or green or tan handles.  Turn one of the handles and it should shut off the water to your sprinkler system.

Other times the Emergency Shutoff Valve is in a box in the ground out by the curb near your water meter.  The valve box will have a green lid.  Sometimes they are difficult to open.  Many times, I had to pry them open with a flat head screwdriver.

 

Inside the valve box is a plastic handle that can turn off the water to the sprinkler system.  It can be blue or red or grey in color.

Many times, the valve box will be full of dirt, and you can’t turn or even see the handle until some of the dirt has been dug out by hand.

 

Water might be shooting up in the air somewhere on your property.  This can be caused by a broken sprinkler pipe or sprinkler valve.

SHUT OFF THE SPRINKLER WATER IF YOU CAN AND GIVE US A CALL.

OKLAHOMA DRAINAGE AND SPRINKLER REPAIR. SERVICING ALL OF CENTRAL AND WESTERN OKLAHOMA.

405 203 9419

Servicing Oklahoma City, Norman, Edmond and all of Central and Western Oklahoma

 

French Drain Installation

Oklahoma Drainage and has been diagnosing and solving Drainage Problems since 1993.  Water has the ability to get into places around your home where you really don’t want it to be.  Some drainage problems are easy to solve.  Typically water enters the problem drainage area one way from one source.  The really tricky drainage problems occur when water enters the problem drainage area from multiple directions and from multiple sources.  Sometimes a secondary water source can’t be seen or identified until the primary water problem source is eliminated.

An example of this occurs when water is running into a problem area in an obvious way over the ground where you can see it.

Simple enough.

A drainage system

is installed with a surface drain as the “intake” with drainage pipe running to an exit point.  Initially the water drains away, and everything looks great.  The next day water is back and is all around the surface drain, but below the edge and it hasn’t rained at all, so no additional water ran over the surface of the ground to flood the area.

The primary water source was solved, (The surface water run off) but the secondary water source was not.  Which was sub-surface water, (ground water) running into the area.  A surface drain can’t drain “ground water.”  A French Drain should have initially been installed instead of a Surface Drain.  A French Drain can drain both Surface Water and Ground Water.

 

A French Drain Can Handle Standing Water

 

Oklahoma Drainage and Sprinkler Repair

Services all of Central Oklahoma including Norman, Moore, Edmond, Yukon, Mustang, Oklahoma City, Midwest City, Del City, Blanchard, Newcastle, Purcell and Chickasha.

 

 

 

Drainage System Installation in Norman

Drainage System Installation in Norman

 

Keep water off your driveway with a channel drain

 Standing water comes from many sources.  It causes damage to sidewalks, driveways, and foundations not to mention plants, trees, and grass. 

Does the side of your house flood because your neighbor doesn’t have gutters, or does your sidewalk turn into a moat after a heavy rain, or worst of all, is water seeping into your foundation and duct work after a thunderstorm? 

These are just a few of the Drainage Problems that Oklahoma Drainage and Sprinkler Repair can help with.  We can design a Drainage System to fit your specific needs. 

We install many types of Drains to solve many types of problems. 

  French Drains, Surface Drains, Channel Drains, Basement Drains, Trench Drains, Basin Drains, and Sump Pumps are utilized.

 

 

4 Inch Drain Pipe Ready to be covered with dirt in Norman.
4 Inch Drainpipe Ready to be covered with dirt in Norman.

 

 

Since 1993 we have gained a lot of experience addressing drainage problems.  Drainage problems can be complicated.  The solution is not always clear to the untrained eye. Oklahoma Drainage has redone or overhauled many drainage systems that were installed by, “weekend warriors, a brother-in-law, or a landscaping company that also installs drains.”  They all can install Drainage Systems, just not very well.

We have over 33 years of experience Diagnosing Drainage Problems.

This ensures that a Drainage System that we install won’t have Drainpipes that are too small, or Surface Drains installed where French Drains Should be placed or Exit Points that allow water to Stand and become stagnant.  The above examples are just three of many “Pit – Falls” that our experienced Drainage System Experts can easily avoid.

Surface Drain installed in Oklahoma City

Surface Drain installed in Oklahoma City

 

We focus on Keeping water off of driveways and Keeping Water from standing on sidewalks every time it rains.  Our Drainage Systems utilize:  French Drains — 3 inch, 4 inch, and 6 inch

Surface Drains, 4 inch, 6 inch, and 12 inch

Channel Drains, 2 inch, and 4 inch

Sump Pumps 3/4 horse to two horse

Servicing Central Oklahoma including Oklahoma City, Norman, Edmond, Yukon, Mustang, Newcastle, Midwest City, Del City, Moore, Blanchard, Choctaw, and all surrounding areas.

Connecting Gutter into French Drain

Connecting Gutter into French Drain

 

 

We install a variety of Drains to solve a variety of Drainage Problems.  Our Drainage Systems can utilize: French Drains, Surface Drains, Channel Drains, Basin Drains, Trench Drains, Basement Drains, and Sump Pumps.

 

 

 

 

Newer Entries