Posts Tagged ‘Norman Oklahoma French Drain’

French Drains in Edmond

 

Oklahoma Drainage  405 203 9419 — We provide:

    French Drain Installation, Surface Drain Installation, Drainage System Installation

 

French Drain Running Through Low Areas

French Drain with stepping stones

WHAT SIZE DRAINPIPE FOR FRENCH DRAINS?

French Drains can be decorated with many types of stone

French Drains can be decorated with many types of stone

French Drains can utilize  several types and sizes of French Drainpipe.  An older type that is not commonly used any more is 4 inch PVC Pipe with large half inch holes drilled in the Pipe.  This doesn’t work very well,  Because the holes are too large and the number of holes in the French Drainpipe are too few.  Also there is no filter or “Soc” around this particular French Drainpipe.  If it is used in sandy or loose soil the holes will clog and the pipe will fill up with sand.  PVC French Drainpipe should be avoided.

ADS French Drainpipe

ADS French Drainpipe is much better, the holes are smaller and much more numerous.  It also comes inside a soc that acts as a filter and helps keep sand and debris out of the French Drainpipe.  It works very well.

French Drain in flowerbed

French Drain in flowerbed

For Small business and Residential French Drains, Four inch ADS Perf/Soc French Drainpipe is adequate and the most common.  It is used for the majority of all French Drains installed.  French Drains can be installed using 3 inch ADS Perf/Soc but many times it is too small and can be overwhelmed by a heavy rain or from a bad design.  (Too many gutter down spouts connected directly into the French Drain, For Example) Three Inch French Drainpipe should be avoided if possible.

6 Inch ADS French Drain

Six inch  ADS Perf/Soc French Drainpipe is usually a good idea when possible.  It carries a much larger volume of water.  Six Inch French Drains are rarely overwhelmed.

Installing Gravel on top of a 6 inch French Drain

Installing Gravel on top of a 6 inch French Drain

The Drawbacks to 6 inch French Drain installation are:

 
1.  The Materials Cost is higher for six-inch French Drain Compared to Four Inch Pipe.
                                                                                                                    2.  Many times 6 Inch French Drain Pipe is too large for many applications, Such as going under a fence or sidewalk.  
                                                                                                                   3.  The trench for a 6 inch French Drain must be much larger than a 4 Inch
                                                                                                                   4.  The amount of gravel or limestone or River Rock used to Cover the 6 inch French Drain is Much larger
 
All things being considered, the performance and longevity of a 6 inch French Drain is well worth it if you are trying to protect something of value to you!  If the higher cost and the additional labor and materials are not a problem and 6 inch French Drain pipe is not too big for what you want to do then a 6 inch French Drain would be the best.  
 

Yukon French Drain

 

French Drain Installation In Yukon Oklahoma Drainage : Servicing all of Central and Western Oklahoma since 1993.Standing Water on Your Driveway?  A Surface Drain set in concrete may be what you need. Or maybe you need a French Drain Running alongside your driveway instead.  Handling water problems is what we are good at.  If you need help, Oklahoma Drainage can provide the best solution for your unwanted water problems.

standing water

A good place for a French Drain

Drainage System in Yukon

Drainage System in Yukon We just finished a 4 inch Drainage System in Yukon.  It was a complicated system to install.  It utilized 4 inch French Drain in the flower beds, 12 inch Surface Drains on the side of the house, 6 inch French Drain along the garage foundation with 2 Pop – Up Emitters in the back yard and 3 Curb Fittings in the front.

First we installed 4 inch French Drain in the flowerbeds on both sides of the front door.  We connected 4 inch solid Drain Pipe into the French Drain and ran them underside walk to the curb.  Next we cut the curb with a concrete saw and installed 3 curb outlets for 3 separate French Drains.

12 Inch Drain Basin

Next we installed 4 12 Inch Drain Basins with grates along both sides of the house continuing with Solid Drainpipe to the Pop-Up Emitters on the back fence.

Finally, we completed the Drainage System by installing a long run of 6-inch French Drain down the side of the garage foundation.   Installing the French Drains in the flower beds was the most difficult and took the most time.  Each French Drain took over a ton of crushed limestone to fill the French Drain trench.  The Six inch French Drain took even more limestone.

 Oklahoma Drainage and Sprinkler Repair –

Hey Oklahoma, We are expanding to service all of Western Oklahoma as well as Central Oklahoma.  If you live in Elk City, and need a French Drain, we can help.  If water is standing on your driveway in Clinton, Give us a call.  Duncan, Lawton, and Altus are all new areas of service for us.

Since 1993 Oklahoma Drainage and Sprinkler Repair has solved all types of standing water and drainage issues.  We install Drainage Systems that utilize French Drains, Surface Drains, Channel Drains, and Sump Pumps depending on the customer’s needs.

If you have water in the wrong place, we can help! We also have Decades of experience repairing all types of Lawn Sprinkler Problems.  Fixing broken sprinkler heads, sprinkler valve problems and controller trouble just to name a few things.

French Drains as part of a Drainage System – 

Many times people use the term ” French Drain” as general name for a Drain used in or around your home.  French Drains are designed to move a lot of water over a large, flooded area.  They are also designed to take water in on the surface of the ground or below the surface of the ground.  This is very important if the water coming into the flooded area is moving through the ground or coming up from underneath.  ” Sub Surface Water Movement.”  The picture below is not a French Drain!

 

 

river rock french drain

A French Drain Can Handle Standing Water

A French Drain can take in water in a broad area.  It can move a much larger volume of water compared to a Surface Drain.  Also, it can move sub surface water moving into the area where a Surface Drain won’t move any water at all.

Surface Drains

are designed to move surface water only on a smaller scale in confined areas.

Each solves specific drainage problems.  A Drainage System may use one or both together or even several using many types of drains.

Standing Water

Do you have standing water in a large area in your yard?  Typically, this calls for a French Drain.  A French Drain is a great way to control standing water in a large grassy area.  It can also protect areas from flooding to a certain degree.  As long as the French Drains capacity to move water is not exceeded.

If the French Drains capacity is exceeded, then water will stand in the drainage area until the rain stops and the drain has time to catch up.  A good way to prevent this is to install a bigger French Drain with a larger pipe.  The difference between a 3 inch French Drain and a 6 inch French Drain is huge.

Another way to beef up a French Drain is to connect gutter down spouts in front of the French Drain.  The water coming off the roof causes suction in the French Drain Behind it.  This greatly increases the French Drains ability to move water without increasing the size of the French Drainpipe.

gutter connect to drain

Gutter Downspout Connected to 6 Inch French Drain

French Drain Inside a Courtyard

Recently we installed a French Drain inside the courtyard of a rest home in Norman.  We had several interesting challenges to overcome that were not typical for a French Drain Installation.

The courtyard was in the center of the home and was a secure area for the patrons.  We had to put down painters tarps to run our wheelbarrows over.

Lots of Dirt to Remove

We took out 44 loads of dirt and brought in 52 loads of Crushed one inch limestone for the French Drain.  Each trip was over a hundred yards from the trailer in the parking lot, in the front door, down the hall, making two turns along the way.

Each time we had to be escorted by security.  Needless to say, the installation of this particular drainage system took a while. In the above picture, the French Drain runs along the low area crossing all the areas where water would stand each time it rained.

Rest home french drain

French Drain in Rest Home Courtyard

Big Mistake

When a French Drain is installed, a big mistake that is made by many people is to cover up the gravel with dirt.  This is a big mistake.  Basically it is ” Putting the cork back in the bottle.”  If the French Drain is in full sun and has a type of grass surrounding it that spreads on its own such a ” Tift” or “Bermuda” , Grass will grow over it and the French Drain will eventually disappear.  Grass covering a French Drain is a good thing if it grows across the drain without adding dirt.  The Grass thatch acts a water filter preventing clogging and extending the life of the Drainage System.

Full Shade

When a French Drain is in Full Shade, or the surrounding grass will not spread on its own, such as with Fescue,  other steps must be taken.  One option is to just leave it alone.  If you don’t mind how it looks, it will drain a large amount of water for many years.  Many times a French Drain can be a landscaping focal point.  They can be dressed up with all kinds of Rocks and Stones and Plants.

 

Just what is a “French Drain?”  Many times people incorrectly

French drain installed
A French Drain can protect your foundation!

use the phrase, “French Drain,”  to apply to many different types of Drains that could be used in a Drainage System.  The term is widely used and many times incorrectly connected to “Surface Drains,” or “Channel Drains.”

Surface Drain

A Surface Drain has a grate that sits on top of a basin.  The basin is underground.  A Drainpipe is connected underground to an outlet on the Drain Basin.  Stormwater Drains through the grate into the Drain Basin.  Once in the Drain Basin, water travels out of the basin through a Drainpipe.  The Stormwater continues downhill in an underground Drainpipe to an exit point.

THIS IS NOT A FRENCH DRAIN!

A Surface Drain may come in many different shapes or sizes.  The Drain Grate may be round or square.  Here is a picture of a common Surface Drain.

A Channel Drain is a type of Surface Drain and many times is installed in concrete across sidewalks or driveways.

A French Drain is completely different from a Surface Drain.  A basic French Drain consists of a Perforated Drainpipe in the bottom of a trench.  The Drainpipe should have a neoprene sock around the Perforated Drainpipe.   This is to ensure that the Drainpipe does not become clogged.

The dirt that was taken out to make the trench is hauled away.  It is replaced by some type of small stone or gravel depending on what is desired or available.

Crushed Limestone

I prefer crushed 1 inch limestone.  It is the most economical option in my area.  Pea Gravel or some other type of small stone can work just as well.    The limestone or gravel is placed in the trench on top of the perforated Drainpipe and filled all the way to the surface (ground level).

In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drainpipe, or the Gravel are installed.  This helps maintain the integrity of the trench over time.  It also increases the cost of the French Drain and the amount of time to install it.  I install a trench liner in a French Drain every time.

A French Drain is designed to handle a large volume of water and cover a large area. The Drain is anyplace the trench goes. It has many applications and can be used in many situations.  It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Downspouts connected to it.

French Drain Downfall

The main downfall of a French Drain is that they, for the most part isn’t very pretty.  They don’t look very nice in a yard once they are completed.
Depending on the area the French Drain is installed and the type of grass around the French Drain, will dictate whether grass grows over the limestone.  Grass can grow up and through the gravel in the French Drain over time eventually covering the gravel.  This is Ok.  It won’t have a measurable effect on the performance of the drain.
DONT COVER THE GRAVEL IN THE FRENCH DRAIN WITH DIRT.  THE FRENCH DRAIN WON’T WORK IF THE TRENCH IS CLOGGED WITH DIRT.  DON’T EVEN INSTALL IT IF YOU ARE GOING TO COVER IT UP WITH DIRT.

DECORATIVE STONE CAN BE USED TO COVER A FRENCH DRAIN AND THEY LOOK GREAT AND LAST A LIFETIME

Installing Cement around Curb Fitting for French Drain

Installing Cement around Curb Fitting for French Drain

French Drain Benefits

A French Drain will move large amounts of water from the Drainage Problem Area to the Exit point.

A French Drain Will Drain away water that gets to the Drainage Problem Area in 3 ways.

1.  Water gets to the problem area by falling from the sky.

2.  Water gets to the problem area by flowing downhill over the ground.

3.  Water gets to the problem area by flowing underground. (Sub-Surface water flow)

Underground Water Flow

Number 3, Sub-Surface water flow is the big consideration.  When doing a Drainage Diagnostic, this is the area that is many times missed or not considered by less experienced companies.  Oklahoma Drainage and Sprinkler Repair rely on 33 years of experience.

Many Times, it is cheaper and more effective to install a French Drain over a Surface Drain.  A Surface Drain can’t move as much water as a French Drain, and a Surface Drain can’t Drain away Sub-Surface water.  Surface Drains should be installed in areas where the Drainage Problem area is smaller and is not affected by sub-surface water.

The drawback to a French Drain, is that it is not a pretty as a Surface Drain.

French Drains do a great job running along foundations and driveways.  A French Drain will keep water away from cement and prevent damage to concrete if water should freeze up against it.  A French Drain can keep your foundation Dry.

 

French Drain Installation

French Drain Pipe running to curb outlet in Oklahoma City.

French Drainpipe running to curb outlet in Oklahoma City.

 

 

Drainage System Installation in Norman

Drainage System Installation in Norman

Drainage Problems and Standing Water have a bad effect on many homes and businesses.  Water in the wrong place causes cracks and deterioration in concrete or cement.  This can cause expensive damage to Driveways, Sidewalks, Foundations.  Drainage Problems and Standing Water also damage Trees, Plants, and Grass that are very important to home or business appearance.

 

 

 

 

channel drain6
A Channel Drain Installed by front door.

2.   Drainage Systems — If you have problems with standing water after a hard rain, or on your sidewalk or driveway, or even leaking into your home, give us a call.  We can quickly diagnose your Drainage Problems and design a Drainage System to fit your needs.  Oklahoma Drainage Utilizes: French Drains, Surface Drains, Basement Drains, Channel Drains, Basin Drains, Trench Drains, and Sump Pumps.  WE INSTALL A VARIETY OF DRAINS TO SOLVE A VARIETY OF PROBLEMS!

Get rid of standing water

 

 

4 Inch Drain Pipe Ready to be covered with dirt in Norman.
4 Inch Drainpipe Ready to be covered with dirt in Norman.

 

Oklahoma Drainage –  We install French Drains, Channel Drains, Surface Drains, Sump Pumps and Sod.

If You live in Oklahoma City and water damaging your foundation, We can install a French Drain for you.

If you live in Norman and have water standing on your driveway, We can install a Channel Drain for you.

If you live in Edmond and have water flooding your basement, We can install a Sump Pump for you.

If you live in Moore and have water washing out your flower bed mulch, We can install a Surface Drain for you.

If you live in Yukon and need grass to grow we can install Sod too!

 

Oklahoma Drainage  Services all of Central Oklahoma including: Norman, Moore, Edmond, Yukon, Mustang, Oklahoma City, Midwest City, Del City, Blanchard, Newcastle, Purcell and Chickasha.

Drainage System Installation in Norman

Drainage System Installation in Norman

 

Do you have Drainage Problems?  Every time it rains, Do you have water standing on your driveway?  Do your gutters turn your sidewalk into a moat?  Does the  side of your house turn into a swamp after a thunder-storm?  Standing  water causes several problems such as dead  grass, sidewalk and foundation deterioration and MOLD to name just a  few.  If you have water seeping into your home things can get even  worse.

Oklahoma Drainage and Sprinkler Repair tackles  these types of Drainage Problems and many other with  the installation of:  FRENCH DRAINS,  SURFACE DRAINS, CHANNEL  DRAINS, BASEMENT DRAINS, TRENCH DRAINS,  BASIN DRAINS, GUTTER DOWNSPOUT  CONNECTS, AND SUMP PUMP INSTALLATION.

can diagnose  your drainage problem and design a drainage system just for your specific needs.

 

French Drain Expert

Oklahoma Drainage 405 203 9419 — We provide:

    French Drain Installation, Surface Drain Installation, Drainage System Installation

 

French Drain Running Through Low Areas

French Drain with stepping stones

WHAT SIZE DRAIN PIPE FOR FRENCH DRAINS?

French Drains can be decorated with many types of stone

French Drains can be decorated with many types of stone

French Drains can utilize  several types and sizes of French Drainpipe.  An older type that is not commonly used any more is 4 inch PVC Pipe with large half inch holes drilled in the Pipe.  This doesn’t work very well,   Because the holes are too large and the number of holes in the French Drain Pipe are too few.  Also there is no filter or “Soc” around this particular French Drainpipe.  If it is used in sandy or loose soil the holes will clog and the pipe will fill up with sand.  PVC French Drain Pipe should be avoided.

ADS French Drainpipe is much better, the holes are smaller and much more numerous.  It also comes inside a soc that acts as a filter and helps keep sand and debris out of the French Drainpipe.  It works very well.

For Small business and Residential French Drains, Four inch ADS Perf/Soc French Drainpipe is adequate and the most common.  It is used for the majority of all French Drains installed.  French Drains can be installed using 3 inch ADS Perf/Soc but many times it is too small and can be overwhelmed by a heavy rain or from a bad design.  (Too many gutter down spouts connected directly into the French Drain, For Example) Three Inch French Drainpipe should be avoided if possible.

Six inch ADS Perf/Soc French Drainpipe is usually a good idea when possible.  It carries a much larger volume of water.  Six Inch French Drains are rarely overwhelmed.

Installing Gravel on top of a 6 inch French Drain

Installing Gravel on top of a 6-inch French Drain

The Drawbacks to 6-inch French Drain installation are:  1.  The Materials Cost is higher for six-inch French Drain Compared to Four Inch Pipe.
                                                                                                                    2.  Many times, 6 Inch French Drainpipe is too large for many applications, such as going under a fence or sidewalk.  
                                                                                                                   3.  The trench for a 6-inch French Drain must be much larger than a 4 Inch
                                                                                                                   4.  The amount of gravel or limestone or River Rock used to Cover the 6-inch French Drain is Much larger
 
All things being considered, the performance and longevity of a 6-inch French Drain is well worth it if you are trying to protect something of value to you!  If the higher cost and the additional labor and materials are not a problem and 6 inch French Drainpipe is not too big for what you want to do then a 6 inch French Drain would be the best.  
 
 
 

French Drains can be installed by themselves, or as part of a Drainage System that uses other French Drains, Surface Drains, or other Drain combinations.  Typically a French Drain is used to protect a broad area that has a lot of standing water.  A French Drain might run alongside a home’s foundation, or beside a driveway, or on any Drainage Project where Sub-Surface water is the primary problem.  If water is running toward your home underground (through sandy soil), A French Drain is the only Solution  for draining away water flowing underground.

 

If you live in Oklahoma City and need a French Drain installed in your yard, or along your driveway, or near your foundation, give us a call.  If you live in Edmond or Norman and need a Surface Drain installed in the concrete in your sidewalk or driveway, we can help.  If you live in Mustang or Yukon and would like to protect your trees or flower beds from standing water with a French Drain.

Since 1993 we have gained a lot of experience addressing drainage problems.  Drainage problems can be complicated.  The solution is not always clear to the untrained eye. We have repaired or overhauled many french drains and drainage systems that were installed by, “weekend warriors, a brother-in-law, or a landscaping company that also installs drains.”  They all can install Drainage Systems, Just not very well.  WE have over 28 years of experience Diagnosing Drainage Problems.  This ensures that a Drainage System that we install won’t have Drain Pipes that are too small, or Surface Drains installed where French Drains Should be placed, or Exit Points that allow water to Stand and become stagnant.  The above examples are just three of many “Pit – Falls” that our experienced Drainage System Experts can easily avoid.

Surface Drain installed in Oklahoma City

Surface Drain installed in Oklahoma City

 

Oklahoma Drainage and Sprinkler Repair 405 203 9419 — We provide:

    French Drain Installation, Surface Drain Installation, Drainage System Installation

    Sprinkler Repair for all aspects of Residential Sprinkler Systems

    Emergency Sprinkler Repair Service, AFTER HOURS AND WEEKENDS.

Sump Pump Installation

Sump Pump Installation

French Drain Running Through Low Areas

French Drain with stepping stones

WHAT SIZE DRAIN PIPE FOR FRENCH DRAINS?

French Drains can be decorated with many types of stone

French Drains can be decorated with many types of stone

French Drains can utilize  several types and sizes of French Drain Pipe.  An older type that is not commonly used any more is 4 inch PVC Pipe with large half inch holes drilled in the Pipe.  This doesn’t work very well,   Because the holes are too large and the number of holes in the French Drain Pipe are too few.  Also there is no filter or “Soc” around this particular French Drain Pipe.  If it is used in sandy or loose soil the holes will clog and the pipe will fill up with sand.  PVC French Drain Pipe should be avoided.

ADS French Drain Pipe is much better, the holes are smaller and much more numerous.  It also comes inside a soc that acts as a filter and helps keep sand and debris out of the French Drain Pipe.  It works very well.

French Drain in flowerbed

French Drain in flowerbed

For Small business and Residential French Drains, Four inch ADS Perf/Soc French Drain pipe is adequate and the most common.  It is used for the majority of all French Drains installed.  French Drains can be installed using 3 inch ADS Perf/Soc but many times it is too small and can be overwhelmed by a heavy rain or from a bad design.  (Too many gutter down spouts connected directly into the French Drain, For Example)  Three Inch French Drain Pipe should be avoided if possible.

Six inch  ADS Perf/Soc French Drain Pipe is usually a good idea when possible.  It carries a much larger volume of water.  Six Inch French Drains are rarely overwhelmed.

Installing Gravel on top of a 6 inch French Drain

Installing Gravel on top of a 6 inch French Drain

Oklahoma Drainage  — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps

Servicing all of Central and Western Oklahoma since 1993.

FRENCH DRAIN IN EDMOND OKLAHOMA, 

Oklahoma Drainage – French Drain Installation, Drainage System Design,  Drain Repair 

Recently Oklahoma Drainage installed a large 6 inch French Drain in Edmond.  The customer had water running under his back porch step and into his basement.  We did a Free Drainage Diagnostic and Estimate.  The French Drain design that we proposed would intercept the surface water and subsurface water that was flowing under the steps.  The French Drain design called for a 6 inch French Drain to be installed above and several feet away from the steps.  It would run around the house parallel to the foundation and about 5 feet to the East.  The French Drain would run past the steps to a point where water must cross the French Drain or run up hill to the steps which in this case was not possible.  Once past the steps, the French Drain would transition to Solid 6 inch Drain Pipe and continue on around the house to the Pop-Up Emitter down hill in the side yard.  Along the way we attached several Gutter Down Spouts into the French Drain.

 

 

 

 

Curb Outlet for French Drain in Edmond

Curb Outlet for French Drain in Edmond

French Drain Installation

Oklahoma Drainage and Sprinkler Repair has been diagnosing and solving Drainage Problems since 1993.  Water has the ability to get into places around your home where you really don’t want it to be.  Some drainage problems are easy to solve.  Typically water enters the problem drainage area one way from one source.  The really tricky drainage problems occur when water enters the problem drainage area from multiple directions and from multiple sources.  Sometimes a secondary water source can’t be seen or identified until the primary water problem source is eliminated.

An example of this occurs when water is running into a problem area in an obvious way over the ground where you can see it.

Simple enough.

A drainage system is installed with a surface drain as the “intake” with drainage pipe running to an exit point.  Initially the water drains away and everything looks great.  The next day water is back and is all around the surface drain, but below the edge and it hasn’t rained at all, so no additional water ran over the surface of the ground to flood the area.  The primary water source was solved, ( The surface water run off ) but the secondary water source was not.  Which was sub-surface water, (ground water) running into the area.  A surface drain can’t drain “ground water.”  A French Drain should have initially been installed instead of a Surface Drain.  A French Drain can drain both Surface Water and Ground Water.

 

river rock french drain install

A French Drain Can Handle Standing Water

FRENCH DRAIN IN EDMOND OKLAHOMA, DRAINAGE CONTRACTOR

Oklahoma Drainage and Sprinkler Repair Recently installed a large 6 inch French Drain in Edmond.  The customer had water running under his back porch step and into his basement.  We did a Free Drainage Diagnostic and Estimate.  The French Drain design that we proposed would intercept the surface water and subsurface water that was flowing under the steps.  The French Drain design called for a 6 inch French Drain to be installed above and several feet away from the steps.  It would run around the house parallel to the foundation and about 5 feet to the East.  The French Drain would run past the steps to a point where water must cross the French Drain or run up hill to the steps which in this case was not possible.  Once past the steps, the French Drain would transition to Solid 6 inch Drain Pipe and continue on around the house to the Pop-Up Emitter down hill in the side yard.  Along the way we attached several Gutter Down Spouts into the French Drain.

 

A  French Drain is completely different from a Surface Drain.  A basic French Drain consists of a Perforated Drain

 

We solve residential and commercial drainage problems.

After a thunder storm, do you have water standing on your driveway, sidewalk, on the side of your house, backyard, front yard, or worst of all — seeping into your home? We can help! We can diagnose your problem and design a drainage system specifically for your needs. We install: French Drains, Surface Drains, Channel Drains, Trench Drains, Basin Drains, Basement Drains, and Sump Pumps.

 

Oklahoma City French Drain Installation, Lawton, Edmond, El Reno, Altus

Oklahoma Drainage 405 203 9419 — We provide:

    French Drain Installation, Surface Drain Installation, Drainage System Installation

French Drain Running Through Low Areas

French Drain with stepping stones

WHAT SIZE DRAIN PIPE FOR FRENCH DRAINS?

Fr

French Drains can be decorated with many types of stone

French Drains can be decorated with many types of stone

French Drains can utilize  several types and sizes of Perforated Pipe.  An older type that is not commonly used any more is 4 inch PVC Pipe with large half inch holes drilled in the Pipe.  This doesn’t work very well,   Because the holes are too large and the number of holes in the French Drain Pipe are too few.  Also there is no filter or “Soc” around this particular French Drain Pipe.  If it is used in sandy or loose soil the holes will clog and the pipe will fill up with sand.  PVC French Drain Pipe should be avoided.

ADS French Drain Pipe is much better, the holes are smaller and much more numerous.  It also comes inside a soc that acts as a filter and helps keep sand and debris out of the French Drain Pipe.  It works very well.

French Drain in flowerbed

French Drain in flowerbed

For Small business and Residential French Drains, Four inch ADS Perf/Soc French Drain pipe is adequate and the most common.  It is used for the majority of all French Drains installed.  French Drains can be installed using 3 inch ADS Perf/Soc but many times it is too small and can be overwhelmed by a heavy rain or from a bad design.  (Too many gutter down spouts connected directly into the French Drain, For Example)  Three Inch French Drain Pipe should be avoided if possible.

Six inch  ADS Perf/Soc French Drain Pipe is usually a good idea when possible.  It carries a much larger volume of water.  Six Inch French Drains are rarely overwhelmed.

Installing Gravel on top of a 6 inch French Drain

Installing Gravel on top of a 6 inch French Drain

The Drawbacks to 6 inch French Drain installation are:  1.  The Materials Cost is higher for six-inch French Drain Compared to Four Inch Pipe.
                                                                                                                    2.  Many times 6 Inch French Drain Pipe is too large for many applications, Such as going under a fence or sidewalk.  
                                                                                                                   3.  The trench for a 6 inch French Drain must be much larger than a 4 Inch
                                                                                                                   4.  The amount of gravel or limestone or River Rock used to Cover the 6 inch French Drain is Much larger
 
All things being considered, the performance and longevity of a 6 inch French Drain is well worth it if you are trying to protect something of value to you!  If the higher cost and the additional labor and materials are not a problem and 6 inch French Drain pipe is not too big for what you want to do then a 6 inch French Drain would be the best.  
 
 
 
 

 

Installing Curb Outlet for French Drain in Oklahoma City

Installing Curb Outlet for French Drain in Oklahoma City

 

Do you have water standing in your yard every time it rains? Does storm-water runoff turn your driveway into a pond? Do your gutters dump enough water on your sidewalk to turn it into a moat? Worst of all, do you have water seeping into your home or business through the walls or foundation? Oklahoma Drainage  can help with these and many other Drainage Problems.

 

 

 

Do you have standing water on your sidewalk or on your driveway every time it rains?  Does your backyard turn into a moat after a downpour?

Do your gutters dump water where you really don’t want it?   Worst of all, do you have water seeping into your home or business?

Standing water causes foundations, sidewalks, and driveways to crack and become undermined.   Mold also can become a serious problem.

Oklahoma Drainage and sprinkler repair can diagnose your drainage problem and design a drainage system to fit your specific needs!    We Install: French Drains, Surface Drains, Channel Drains, Trench Drains, Basin Drains, Basement Drains, and Sump Pumps.  Some drainage systems require more than one type of drain.

French Drain walk way

French Drain Installed along and under walk way to pool.

Servicing Central Oklahoma Including: Norman, Oklahoma City, Moore, Edmond, Midwest City, Del City, Yukon, Mustang, Purcell, and Blanchard.

new curb outlet

Curb outlet with more than 6 inches of fall

 

Harsh weather in Oklahoma seems to becoming more common.  In 2013,  Norman Oklahoma had 4 inches of rain in two hours.  That’s the most rain in a short time that I can remember.  Storm-Water runoff can cause damage to all types of property and buildings.  Water getting inside your house is never a good thing.  A Drainage System that utilizes a French Drain can help.

French Drain protects sidewalk

French Drain keeps water off of sidewalk

Drains can protect your home and property from water damage.

Large 6 Inch French Drain Installed in Norman
Large 6 Inch French Drain Installed in Norman

Drainage Systems can be made up of one drain or a combination of many drains.  Drainage  problems can be very complex.   Complex Drainage Problems may require a combination of several different types of drains all inter-connected and working together.  Other times the drainage problem may be simple and straight-forward requiring only one drain or several of the same type of drain connected together.

An example of a complex drainage system would be:  A French Drain in the back yard connected to a Surface Drain near a flower bed connected to several gutter downspouts, which are connected to a Channel Drain going across a driveway, which is connected to additional Surface Drain in the front yard, which runs to a Curb Fitting that lets all the water drain out on to the street.

A simple Drainage System might consist of a Surface Drain that is connected to a second Surface Drain which runs to a Pop-up Emitter which lets water drain over the curb and into the street.

An “Exit Point” is the term used for where all the water leaves the Drainage System.  Determining the Exit Point is very critical.  It is one of the first things we do when diagnosing a Drainage Problem.

Gutter to French Drain

Connecting Gutter to French Drain

Drainage Systems can:

1.  Keep water away from foundations — A French Drain is best because it can move Surface Water and Sub-Surface Water (water moving under ground) away from the foundation.  Many times less experienced companies install Surface Drains to keep water away from foundations.  This can be a big mistake.  A Surface Drain can’t move or drain Sub-Surface Water.   Also A Surface Drain often can’t move enough water fast enough and easily becomes overwhelmed during a heavy rain.  A Surface Drain also can’t cover or protect a broad enough area. Surface Drains should be designed in a Drainage System to be located in smaller Drainage Areas moving moderate amounts of water.  Surface Drains look better than French Drains.  If ,”appearance” is more important than Drainage Capacity, Go with the Surface Drain.  Just know what you are getting into and what your expectations should be. One side of a foundation alone,  can be over 100 feet.  A 4 inch or 6 inch French Drain is best when protecting a large area such as a foundation.

Surface Drain Installed next to sidewalk in Oklahoma City.
Surface Drain Installed next to sidewalk in Oklahoma City.

2.  Keep water away from small or enclosed areas.  This might be a low area just through a gate on the side of a house, or the low area between a flowerbed and the wall of a house, or standing water on or near a sidewalk or driveway.  These types of Drainage Problems are best served with Surface Drains.  A Surface Drain can move water away from a low area that is relatively small.  This can occur in yards, flowerbeds, sidewalks and driveways.  A Surface Drain is designed to move Surface Water away from a problem area to a predetermined exit point.  Surface Drains are available in many sizes.  How quickly they remove standing water is usually determined by the size of the Drain Pipe that is connected to the Drain.

Simply put, a Drainage System is one or a group of underground Drain Pipes that take water away from a place that has water standing on it or flowing across it.  The water that is in the problem area, can be causing damage or may be inconvenient or both.  (Usually Both)  A simple Drainage System is a Drain for the water to enter, a Drain Pipe to move the water away from the Drain, and an Exit Point for the water to be released out of the Drain Pipe.

Drainage Systems quickly can become more complicated.  Considerations must include:

How does the water get to the problem area?  There may be one or many sources.

Water Sources:

1.  It falls from the sky directly

2.  It flows down hill over the surface (surface water)

3.  It flows underground under the surface (sub-surface water)

4.  It flows from the edge of a roof ( There may be many roofs near the problem area, neighbors etc.)

5.  It flows from a gutter downspout

6.  It flows over the edge of a gutter because the gutter is too small is is clogged

7.  It flows up from the ground (seeps and springs are common in Oklahoma)

8.  It flows from a sprinkler system use ( yours or your neighbors)

9.  It flows from a leaking pipe ( water mains, water meters, water lines, sprinkler pipes, sprinkler valves)

There are other reasons for Drainage Problems, the above reasons are just the most common.

Once the number of water sources is determined, a rough estimate of the amount of water that needs to be drained away on average must be estimated.  This can be simplified down to “SMALL, MEDIUM, OR LARGE AMOUNTS OF WATER TO BE DRAINED AWAY.  You don’t have to be an engineer trying to calculate fluid dynamics.  Experience at diagnosing drainage problems helps however.  How much water needs to be moved will help determine the type and size of the Surface Drain or French Drain that needs to be installed.  It also helps to determine the size of Drain Pipe required for the Drainage System.  A good rule to follow is, “If in doubt, install a larger Drain and Drain Pipe.”  Unused Drainage Capacity is better than property damage caused by a Drain that is overwhelmed by too much water.

For home and small business use typical materials used are:

6 inch, 9 inch, and 12 inch Surface Drains –

3 inch, 4 inch, and 6 inch Drain Pipes —

3 inch, 4 inch, and 6 inch French Drains —

French Drains move more water than Surface Drains —

French Drains move Surface Water and Sub-Surface Water

Surface Drains move Surface Water only

Surface Drains look nicer than French Drains in most cases

Once the type and number of drains is determined and what size Drain Pipe will connect them, an exit point must be selected.  (Where is the Drainage System going to take the water to and release it?)

The Drainage Curb Fitting is installed when the desired exit point for the French Drain will release the Drainage Water into the Street.   The Drainage Curb Fitting is rectangular in shape and made to be installed through the curb.  A small section of Curb is cut out with a concrete saw.  The Section is a few inches wider than the Drainage Curb Fitting.  We then install new concrete around the curb fitting.  Once the concrete has dried, the Drain Pipe coming from a French Drain or Surface Drain is connected to the Drainage Curb fitting and then covered with dirt.

The Drainage Pop-Up Emitter is connected to the end of a Drain Pipe.  It is downhill from a French Drain or a Surface Drain.  It is a small release basin with a green pop-up lid.  When releasing water, it pops up about an inch to release the water from the French Drain or Surface Drain.  When the Storm Water has moved through the Drainage System and out of the Pop-Up Emitter, the green lid closes back to its original closed position.  The emitter is designed to release water out into a yard or down a hill or other desirable Drainage Exit Point where there is no curb.

Popup Emitter to release water from a Drainage System in Yukon.
Popup Emitter to release water from a Drainage System in Yukon.

Drainage System installation and design is a big part of our business.  Does your sidewalk turn into a moat after a hard rain?  Does part of your yard look like a pond after a thunderstorm?  Worst of all, are you experiencing concrete deterioration to your foundation, sidewalk, or driveway.  Oklahoma Drainage can design a Drainage System to solve your Drainage Problems.  Our Drainage Systems can be simple or complex.  We utilize, French Drains, Surface Drains, Channel Drains, Basin Drains, Basement Drains, Trench Drains, and Sump Pumps.  Estimates are free

 

 

Oklahoma City Channel Drain Repair

If you have trouble with your channel drain, we can help.

 

 

Oklahoma City French Drain, Edmond, Moore, Norman, Yukon

French Drain Installation Or Do You Need A Surface Drain?

Many Folks don’t know the difference.   Actually there are many differences and a few similarities.  One difference is, a French Drain takes in a larger amount of water into the drain Pipe than a Surface Drain.  There are advantages to Surface Drains as well.

 

A French Drain Is a Perforated Drain Pipe in a Trench with Gravel or Limestone covering the trench with the pipe.  Many times there is a “Sock” around the pipe to act as a filter.

Oklahoma Drainage  — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps

Servicing all of Central and Western Oklahoma since 1993.

French Drains as part of a Drainage System – 

Many times people use the term ” French Drain” as general name for a Drain used in or around your home.  French Drains are designed to move a lot of water over a large flooded area.  They are also designed to take water in on the surface of the ground or below the surface of the ground.  This is very important if the water coming into the flooded area is moving through the ground or coming up from underneath.  ” Sub Surface Water Movement.”  The picture below is not a French Drain!

A French Drain looks like this

A French Drain Can Handle Standing Water

A French Drain can take in water in a broad area.  It can move a much larger volume of water compared to a Surface Drain.  Also, it can move sub surface water moving into the area where a Surface Drain won’t move any water at all.

Surface Drains are designed to move surface water only on a smaller scale in confined areas.

Each solves specific drainage problems.  A Drainage System may use one or both together or even several using many types of drains.

Do you have standing water in a large area in your yard?  Typically this calls for a French Drain.  A French Drain is a great way to control standing water in a large grassy area.  It can also protect areas from flooding to a certain degree.  As long as the French Drains capacity to move water is not exceeded.  If the French Drains capacity is exceeded then water will stand in the drainage area until the rain stops and the drain has time to catch up.  A good way to prevent this is to install a bigger French Drain with a larger pipe.  The difference between a 3 inch French Drain and a 6 inch French Drain is huge.

Another way to beef up a French Drain is to connect gutter down spouts in front of the French Drain.  The water coming off the roof causes suction in the French Drain Behind it.  This greatly increases the French Drains ability to move water without increasing the size of the French Drain Pipe.

Gutter Downspout Connected to 6 Inch French Drain

 

Oklahoma Drainage  recently diagnosed a Drainage Problem in  South Oklahoma City.  The Home owner had a sump Pump in their basement that was fed from a French Drain outside the Basement Wall.  The French Drain was 14 feet down along the Stem wall of the house.  The French Drain Pipe was cheap and had collapsed.  We brought in a Mini Excavator and dug up the pipe and replaced it with Durable ADS 4 inch perf/soc French Drain pipe.  In the end, we were able to dig up the pipe and Replace it.

New Trench for French Drain

Next we installed a new exit for the water by installing a curb fitting.

No more flooding in the customers basement.  A few weeks later our customer was able to lay carpet in the basement with no problems.

Large 6 Inch French Drain Installed in Norman
Large 6 Inch French Drain Installed in Norman

Drainage Systems can be made up of one drain or a combination of many drains.  Drainage  problems can be very complex.   Complex Drainage Problems may require a combination of several different types of drains all inter-connected and working together.  Other times the drainage problem may be simple and straight-forward requiring only one drain or several of the same type of drain connected together.

An example of a complex drainage system would be:  A French Drain in the back yard connected to a Surface Drain near a flower bed connected to several gutter downspouts, which are connected to a Channel Drain going across a driveway, which is connected to additional Surface Drain in the front yard, which runs to a Curb Fitting that lets all the water drain out on to the street.

A simple Drainage System might consist of a Surface Drain that is connected to a second Surface Drain which runs to a Pop-up Emitter which lets water drain over the curb and into the street.

An “Exit Point” is the term used for where all the water leaves the Drainage System.  Determining the Exit Point is very critical.  It is one of the first things we do when diagnosing a Drainage Problem.

Drainage Systems can:

1.  Keep water away from foundations — A French Drain is best because it can move Surface Water and Sub-Surface Water (water moving under ground) away from the foundation.  Many times less experienced companies install Surface Drains to keep water away from foundations.  This can be a big mistake.  A Surface Drain can’t move or drain Sub-Surface Water.   Also A Surface Drain often can’t move enough water fast enough and easily becomes overwhelmed during a heavy rain.  A Surface Drain also can’t cover or protect a broad enough area. Surface Drains should be designed in a Drainage System to be located in smaller Drainage Areas moving moderate amounts of water.  Surface Drains look better than French Drains.  If ,”appearance” is more important than Drainage Capacity, Go with the Surface Drain.  Just know what you are getting into and what your expectations should be. One side of a foundation alone,  can be over 100 feet.  A 4 inch or 6 inch French Drain is best when protecting a large area such as a foundation.

Surface Drain Installed next to sidewalk in Oklahoma City.
Surface Drain Installed next to sidewalk in Oklahoma City.

2.  Keep water away from small or enclosed areas.  This might be a low area just through a gate on the side of a house, or the low area between a flowerbed and the wall of a house, or standing water on or near a sidewalk or driveway.  These types of Drainage Problems are best served with Surface Drains.  A Surface Drain can move water away from a low area that is relatively small.  This can occur in yards, flowerbeds, sidewalks and driveways.  A Surface Drain is designed to move Surface Water away from a problem area to a predetermined exit point.  Surface Drains are available in many sizes.  How quickly they remove standing water is usually determined by the size of the Drain Pipe that is connected to the Drain.

Simply put, a Drainage System is one or a group of underground Drain Pipes that take water away from a place that has water standing on it or flowing across it.  The water that is in the problem area, can be causing damage or may be inconvenient or both.  (Usually Both)  A simple Drainage System is a Drain for the water to enter, a Drain Pipe to move the water away from the Drain, and an Exit Point for the water to be released out of the Drain Pipe.

Drainage Systems quickly can become more complicated.  Considerations must include:

How does the water get to the problem area?  There may be one or many sources.

Water Sources:

1.  It falls from the sky directly

2.  It flows down hill over the surface (surface water)

3.  It flows underground under the surface (sub-surface water)

4.  It flows from the edge of a roof ( There may be many roofs near the problem area, neighbors etc.)

5.  It flows from a gutter downspout

6.  It flows over the edge of a gutter because the gutter is too small is is clogged

7.  It flows up from the ground (seeps and springs are common in Oklahoma)

8.  It flows from a sprinkler system use ( yours or your neighbors)

9.  It flows from a leaking pipe ( water mains, water meters, water lines, sprinkler pipes, sprinkler valves)

There are other reasons for Drainage Problems, the above reasons are just the most common.

Once the number of water sources is determined, a rough estimate of the amount of water that needs to be drained away on average must be estimated.  This can be simplified down to “SMALL, MEDIUM, OR LARGE AMOUNTS OF WATER TO BE DRAINED AWAY.  You don’t have to be an engineer trying to calculate fluid dynamics.  Experience at diagnosing drainage problems helps however.  How much water needs to be moved will help determine the type and size of the Surface Drain or French Drain that needs to be installed.  It also helps to determine the size of Drain Pipe required for the Drainage System.  A good rule to follow is, “If in doubt, install a larger Drain and Drain Pipe.”  Unused Drainage Capacity is better than property damage caused by a Drain that is overwhelmed by too much water.

For home and small business use typical materials used are:

6 inch, 9 inch, and 12 inch Surface Drains –

3 inch, 4 inch, and 6 inch Drain Pipes —

3 inch, 4 inch, and 6 inch French Drains —

French Drains move more water than Surface Drains —

French Drains move Surface Water and Sub-Surface Water

Surface Drains move Surface Water only

Surface Drains look nicer than French Drains in most cases

Once the type and number of drains is determined and what size Drain Pipe will connect them, an exit point must be selected.  (Where is the Drainage System going to take the water to and release it?)

The Drainage Curb Fitting is installed when the desired exit point for the French Drain will release the Drainage Water into the Street.   The Drainage Curb Fitting is rectangular in shape and made to be installed through the curb.  A small section of Curb is cut out with a concrete saw.  The Section is a few inches wider than the Drainage Curb Fitting.  We then install new concrete around the curb fitting.  Once the concrete has dried, the Drain Pipe coming from a French Drain or Surface Drain is connected to the Drainage Curb fitting and then covered with dirt.

The Drainage Pop-Up Emitter is connected to the end of a Drain Pipe.  It is downhill from a French Drain or a Surface Drain.  It is a small release basin with a green pop-up lid.  When releasing water, it pops up about an inch to release the water from the French Drain or Surface Drain.  When the Storm Water has moved through the Drainage System and out of the Pop-Up Emitter, the green lid closes back to its original closed position.  The emitter is designed to release water out into a yard or down a hill or other desirable Drainage Exit Point where there is no curb.

Popup Emitter to release water from a Drainage System in Yukon.
Popup Emitter to release water from a Drainage System in Yukon.

Drainage System installation and design is a big part of our business.  Does your sidewalk turn into a moat after a hard rain?  Does part of your yard look like a pond after a thunderstorm?  Worst of all, are you experiencing concrete deterioration to your foundation, sidewalk, or driveway.